• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.143-150
• /
• 1998

The evaluation of joint fatigue strength of light weight materials for electrical vehicle body has been performed through single lap joint tests with the design parameters such as joint style, adherend, bonding overlap length and bonding thickness. Fatigue strength was evaluated through 5-Hz, tension-tension, load controlled test with the stress ratio zero value. It is experimentally observed that fatigue strength of joint increases for the increase of overlap length. The combinations of Al-Al and Al-FRP adherends show that fatigue strength of joint is hardly changed for the increase of bonding thickness, but FRP-FRP adherend specimen shows that fatigue strength of joint increases after decreases for the increase of bonding thickness. Al-Al adherend specimen has much higher fatigue length than Al-FRP and FRP-FRP adherend specimens. Riveting at adgesive bonded joint gives little effect on fatigue strength.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.59-61
• /
• 2006

The $CO_2$ laser cladding was conducted on an AC2B alloy with feeding Fe-based powders. A powder feeding rate (PFR) and a travel velocity were related with the cracks adjacent to the Fe/Al interface. Preheating temperature was varied to study the interface crack. Preheating to $250^{\circ}C$ during the laser cladding suppressed the interface crack ratio (ICR). The ICR was limited for the single pass clad and the reciprocating test for the slide wear was conducted on an overlay cladding experiment. Comparing with no overlap overlay, the overlay clad with 50% overlap showed better wear resistance.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.39-44
• /
• 2004

A heat and room temperature construction method of asphalt have been mainly applying to rooftop waterproofing in concrete structure, and the rest construction method are sheet, membrane and mortar waterproofing construction method. In particular, joint method in sheet waterproof method is as overlap joint which on being reinforced with fiber and tape, have been applying for job site to mechanical fix using protection disk and anchorage and metal ironwork on the end of sheet. These construction method cause cutting off joint of sheet as behavior of structure according to repairs of sheet itself and thermal conduct, outdoor air environment. In conclusion, we analyzed and examined the application of various sheets and piece ashes about superior 'I' joint which divide from one and the other sheet and progressed about joint construction method of fixing method for overlap.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.825-829
• /
• 2009

In this paper, we examine the fundamental performance of image coding schemes based on multipulse model. First, we introduce several kinds of pulse search methods (i.e., correlation method, pulse overlap search method and pulse amplitude optimization method) for the model. These pulse search methods are derived from auto-correlation function of impulse responses and cross-correlation function between host signals and impulse responses. Next, we explain the basic procedure of multipulse image coding scheme, which uses the above pulse search methods in order to encode the high frequency component of an original image. Finally, by means of computer simulation for some test images, we examine the PSNR(Peak Signal-to-Noise Ratio) and computational complexity of these methods.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.27-34
• /
• 1997

The effects of the intake and exhaust valve timing to improve the engine performance in a spark ignition 3-cylinder LPG engine with a closed loop fuel supply system were studied. The engine torque and power have been measured using the 75kW EC-dynamometer while adjusting the optimal fuel consumption ratio with a solen- oid driver. As the results from this experiment, when intake valve opening is $12^{\circ}$ BTDC, intake valve closing is $36^{\circ}$ ABDC, exhaust valve opening is $12^{\circ}$ ATDC, and exhaust valve closing is $36^{\circ}$ BBDC respectively, the best torque characteristics in low and high speeds for a gives engine were obtained. And also we could find that the torque characteristics in low speeds were affected by the timing of exhaust valve open. An increased valve overlap by the EVC delay was ineffectual to the torque characte- ristics improvement in high speeds.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.409-410
• /
• 2007

In this paper, we propose a new method for overlap and add synthesis using phase shaping factor in a sinusoidal synthesis method of speech signal, which improves continuity and SNR(Signal Noise Ratio) efficiency of synthesized speech.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.19 no.40
• /
• pp.329-339
• /
• 1996

This study presents the eigen ethnic function and mathematical processing method of human information. Human information can be definded as the overlap area taking the superposition property composed of intuition and sensory in stimulus/response (S/R) model, In S/R model, the intuition and sensory eigen ethnic function acts on the forming of perception. Perception process by the superposition property of intuition and sensory analogy to the basic neural network model. This analogy model extends to the analysis method. As an analysis method, optimal ratio number induced to the golden section ratio. Golden section ratio drived out by diverse source and implicated to the sensory and intuitive context such as beauty, harmony, optimality etc. This numerical orders can be applied to analysing the Perception process and extended to pursue the Potential human behavior, On the basic of proposed applying method, an illustrative mathematical examples are presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1001-1010
• /
• 1999

Thermo-mechanical behavior of discontinuous shape memory alloy(SMA) reinforced polymeric composite has been studied using modified shear lag theory and finite element(FE) analysis with 2-D multi-fiber model. The aligned and staggered models of short-fiber arrangement are employed. The effects of fiber overlap and aspect ratio on the thermomechanical responses such as the thermal expansion coefficient are investigated. It is found that the increase of both tensile stress(resistance stress) in SMA fiber and compressive stress in polymer matrix with increasing aspect ratio is the main cause of low thermal deformation of the composite.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.436-439
• /
• 2007

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.848-853
• /
• 2001

Electrostatic actuation was adopted for ease of fabrication. We proposed a new driving scheme that uses the vector sum of force generated by comb-finger and by parallel plate. The moving and fixed electrodes are arranged to maximize the driving force. In this paper, an electrostatic field analysis is performed by Maxwell analysis tool for micro actuators. From the analysis, a comb-parallel type micro-actuator with 4${\mu}{\textrm}{m}$ width, 6${\mu}{\textrm}{m}$ overlap and 45${\mu}{\textrm}{m}$ height could be designed. In order to compare the new type of actuator with the conventional comb type of actuator, we arranged that both types have the same area and the same number of actuators. To make a high aspect ratio structure, we are developing fabrication process using SU-8 and electro-plating.