• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.376-385
• /
• 1991

For manufacturing trimming-free plates which have rectangular shaped edges and straight edges in as-rolled state, it is necessary to investigate rolling characteristics of overlap, bulge and width deviation etc. in a standardized plate rolling process. The present wok is for preventing edge overlap as the first approach to develop trimming-free plate rolling technique. An experimental study on overlap control was done with plasticine material in order to examine influence factors and find a control method by use of a laboratory mill scaled down to one tenth of actual production mill. It was found that edge overlapping was increased with the increase of slab thickness and of broadside rolling ratio, but decreased with the increase of chamfered amount on slab edges. In the simulated rolling experiment with edge chamfered slabs of various chamfered angles, the chamfered angle of 60.deg. was the most effective one for reducing overlapping irrespective of slab thickness and of broadside rolling ratio.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.129-133
• /
• 2007

Focused Ion Beam(FIB) systems is a useful tool for the fabrication of micro-nano scale structures. In this study, the effects of FIB etching on the Au microstructure are systematically investigated. As the fabrication parameters, ion dose, dwell time and beam overlap ratio are studied. First, the increases of Ga ion dose makes the milling yield higher and the sidewall of milling profile steeper. Dwell time is found to have little effects on the milling profile due to the relatively large milling area of $1\times1{\mu}m^2$ used in this study. However, beam overlap significantly affects not only milling rate but also milling profile. As the beam overlap ratio changes from positive to negative, the development of regular cross-stripe patterns at the bottom with low milling rate is observed.

• Journal of Communications and Networks
• /
• v.1 no.3
• /
• pp.158-165
• /
• 1999

This paper studies interconnection of DCS1800 and GSM900 dual-band networks. Two types of interconnection config-urations for GSM services, non-overlap and overlap, are described. We propose analytic and simulation models to investigate the ben-efit of the overlap configuration. Our results explain how the radio channel capacities, the inter-system handoff failure rate, the origi-nating call traffic ratio and the offered loads affect the system per-formance. This study indicates that with appropriate overlap con-figuration, the GSM dual-band network can significantly improve the quality of cellular service.

• Journal of Welding and Joining
• /
• v.22 no.1
• /
• pp.58-64
• /
• 2004

The control of the weld bead shape is important in laser welding of the small parts. The effects of laser welding parameters on the weld bead shape in the pulsed Nd:YAG laser welding of STS 304L material were investigated. Shielding gas type, flow rate, pumping voltage, pulse frequency, pulse width, focal position and overlap distance were selected as laser welding parameters. Experiments were designed and conducted using the Taguchi method which was a statistical experimental method. The weld bead width, penetration, area and aspect ratio were measured and analysed as the weld bead shape properties and the welding parameters were optimized to maximize the weld aspect ratio. Weld aspect ratio were greatly affected by the pulse width, pumping voltage and pulse frequency, and somewhat by the overlap distance, and little by the shielding gas type, flow rate and focal position. A confirmation experiment were conducted using the optimized welding parameters.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.1
• /
• pp.33-41
• /
• 2014

In a supersonic turbine, A rotor overlap technique reduced the chance of chocking in the rotor passage, and made the design pressure ratio satisfied. However, the technique also made additional losses, like a pumping loss, expansion loss, etc. Therefore, an approximate optimization technique was appled to find the optimal shape of overlap which maximizes the improvement of the turbine performance. The design variables were shape factors of a rotor overlap. An optimal design for rotor overlap reduces leakage mass flow rate at tip clearance by about 50% and increases about 4% of total-static efficiency compared with the base model. It was found that the most effective design variable is the tip overlap and that the hub overlap size is the lowest.

• Journal of Powder Materials
• /
• v.24 no.3
• /
• pp.210-215
• /
• 2017

In this study, STS316L powders prepared by gas atomization are used to manufacture bulk structures with dimensions of $10{\times}10{\times}10mm^3$ using selective laser melting (SLM). The microstructures and hardness of the fabricated 316L stainless steel has been investigated with the laser beam overlap varied from 10% to 70%. The microstructures of the fabricated STS316L samples show a decrease in the balling and satellite of powders introducing defect in the bulk samples and the porosity caused by the gap between the molten metal pools disappearing as the overlap ratio increases, whereas a low overlap ratio results in significant balling and a large amount of isolated powders due to the increased gap between the melt pools. Furthermore, the highest value in Vickers hardness is obtained for the sample fabricated by 30% overlapped laser beams. These results show that the overlap ratio of laser beams in the SLM process should be considered as an important process parameter.

• Journal of Korean Society for Geospatial Information Science
• /
• v.21 no.2
• /
• pp.117-123
• /
• 2013

This study focuses on the determination of optimal photographing angle and overlapping ratio for automatic image stitching system using a non-metric camera module with motorized head. Photographing overlap was calculated considering the angle of view on different kinds of lenses and moving angle of motorized head per each option, and optimal photographing angle and overlapping ratio could be determined through the experimental result using the operating time, data volume and performance of image stitching. Through this experiment, we could find that it was effective to take a picture with $36^{\circ}$ of interval(33.82% of overlap) in vertical direction and $24^{\circ}$ or $30^{\circ}$ of interval(36.51% or 20.63% of overlap) in horizontal direction using 35mm lens for automatic image stitching system.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.325-330
• /
• 2011

A rotor overlap technique was adapted to improve the performance of a axial turbine. The technique secured sufficient flow passage by additional height at the rotor tip and hub. especially in a supersonic turbine, the technique reduced the chance of chocking in the rotor passage, and made to be satisfied the design pressure ratio. However, the technique also made additional losses, like a pumping loss, expansion loss, etc. Therefore, a optimization technique was appled to maximize the improvement of the turbine performance. An approximate optimization method was used for the investigation to secure the computational efficiency. The design variables was shape factors of a rotor overlap. Results indicated that a significant improvement in turbine performance can be achieved through the optimization of the rotor overlap.

• Smart Structures and Systems
• /
• v.22 no.2
• /
• pp.139-150
• /
• 2018

A variable electromotive-force generator (VEG), which is a modified generator with an adjustable overlap between the rotor and the stator, is proposed to expand the operational range of a regular generator through a simple and robust active control strategy. It has a broad range of applications in hybrid vehicles, wind turbines, water turbines, and similar technologies. A mathematical model of the VEG is developed, and a novel prototype is designed and fabricated. The performance of the VEG with an active control system, which adjusts the overlap ratio based on the desired output power at different rotor speeds for a specific application, is theoretically and experimentally studied. The results show that reducing the overlap between the rotor and the stator of the generator results in reduced torque loss of the generator and an increased rotational speed of the generator rotor. A VEG can improve the fuel efficiency of hybrid vehicles; it can also expand operational ranges of wind turbines and water turbines and harness more power.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2020.05a
• /
• pp.595-598
• /
• 2020

IoU (Intersection over Union) is the most commonly used index in target detection. The core requirement of target detection is what is in the image and where. Based on these two problems, classification training and positional regression training are needed. However, in the process of position regression, the most commonly used method is to obtain the IoU of the predicted bounding box and ground-truth bounding box. Calculating bounding box regression losses should take into account three important geometric measures, namely the overlap area, the distance, and the aspect ratio. Although GIoU (Generalized Intersection over Union) improves the calculation function of image overlap degree, it still can't represent the distance and aspect ratio of the graph well. As a result of technological progress, Bounding-Box is no longer represented by coordinates x,y,w and h of four positions. Therefore, the IoU can be further optimized with the center point and aspect ratio of Bounding-Box.