• Composites Research
• /
• 제14권2호
• /
• pp.33-42
• /
• 2001

DSC(differential scanning calorimetry)를 이용하여 S2-유리섬유/폴리에스터 프리프레그 복합재료의 경화반응식을 구성하였다. 구성된 경화식과 블리더의 수지 함침에 의한 열전달 조건의 변화를 고려하여, 두꺼운 복합재료의 두께 방향 위치에 따른 온도분포를 계산하였다. 유래섬유 복합재료의 경화중 온도과승을 줄이기 위한 방법으로 냉각 및 재가열 구간을 도입하여 경화 사이클을 개선하였다. 냉각-재가열 구간이 없는 기존의 경화 사이클과 개선된 경화 사이클로 두꺼운 복합재료를 각각 제조하여 short beam shear 시험 및 Barcol 경도시험을 실시하고, 그 결과를 비교하였다.

• 한국화재소방학회논문지
• /
• 제22권5호
• /
• pp.61-66
• /
• 2008

본 연구에서는 특정물질의 과열로 인한 이상 상태를 조기에 감지하여 화재 및 폭발로의 전이 위험성을 사전에 예방할 수 있는 방법 중 하나로 열변색 색소를 유효성분으로 한 겔성형체를 제조하여 그 특성을 평가하였다. 또한 과열감지용 대상물에 대한 적용성을 확대하기 위하여 성형체는 원료물질의 종류와 함량, 그리고 제조방법에 따라 점탄성형과 도포형의 2가지로 제조하였다. 변색성 시험, 점도 특성, 변색 개시시간, FT-IR 분석을 수행한 결과 이상 조건을 효과적으로 감지하여 변색 기능을 나타낼 수 있는 물질이 제조되어 다양한 응용이 가능할 것으로 사료된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.233-236
• /
• 2001

Parallel operation scheme to several transformers is adopted because of the load increase, economic problem, or load shedding. For the transformer's parallel operation, loads proportional to each transformer's capacity must be allotted, and circulation currents must be limited as much as without causing any problem in a real operation. But, both transformers in parallel operation can be tripped when either faults at lower voltage side of a transformer or faults in a bus occurs. Therefore, parallel operation scheme to distribution transformers in Korea is not adopted in a normal state but only when loaded or load-shedded. These are due to the insufficiency of the construction in communication network and AVR scheme. Besides that, those are because bus bar protection scheme to lower voltage side of a transformer is not applied. In spite of enormous initial investment costs, advanced countries take so much account of power system reliability and stable supply that they adopt the parallel operation scheme in a normal state. One of the problems in parallel operation is the overheat of transformers due to the excessive circulation currents. This paper presents the scheme that controls voltages between both transformers using circulation currents that occurs in parallel operation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1039-1040
• /
• 2006

The resonant converters cause the high voltage stress according to the input voltage, which increases the conduction loss in converter power switches. The topology of LLC half bridge resonant converter provides ZVS characteristic and also the stress of voltage and current is not higher than that of the general resonant converters. So we can expect the higher efficiency. In this paper, the LLC resonant converter is designed for the notebook computer adapter. In the adapter design, we should consider the weight, the size and overheat of the adapter. Thus the higher efficiency is an essential particular. First of all, the optimal design of transformer is the most important facts. Some parameters should be considered in order to get the highest efficiency. The adapter is designed through the considering of these parameters including the PFC circuit of the pre-regulator. It converts AC line input into about $400V_{DC}$ Link voltage of the LLC converter input and the converter has $16V_{DC}/90W$ ratings. The efficiency measured is about up to 92%.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.169-170
• /
• 2006

대형화, 고압화되고 있는 전력설비는 사고가 발생할 경우 그에 수반되는 산업, 경제, 사회적인 손실의 규모가 매우 커지는 경향을 가진다. 특히 적정온도 이상에서의 운전은 전력설비의 오동작을 일으키는 주요한 원인 중 하나이므로 비정상적인 온도상승을 조기에 감지하여 사고의 가능성을 감소시키는 시스템의 개발은 안정적인 전력설비 운용에 반드시 필요한 요소기술이다. 기존의 감시 시스템은 대부분 여러 위치의 정보를 동시에 얻기 위하여 여러 개의 개별 센서를 배열하여야하므로 대형중량화가 불가피하다는 단점을 갖고 있다. 그러나 광섬유 FBG 온도센서는 전자기 간섭의 영향을 받지 않고, 여러 개의 센서를 하나의 광섬유 라인에 설치하여 동시에 여러 부위의 온도를 측정할 수 있는 준분배형 온도센서 구현이 가능하다는 장점으로 과열감시 시스템에 적합한 센서로 인식된다. 본 연구에서는 광섬유 FBG 온도센서를 이용하여 변압기 단락시험을 통해 변압기의 온도 변화를 T-type thermocouple(이하 TC)과 동일한 지점에서 측정하고, 그 데이터를 비교분석함으로써 광섬유 FBG 온도센서 시스템의 신뢰성을 검증하였고, 이를 전력용 변압기 과열감시 시스템으로 적용할 수 있음을 제시하였다.

• 설비공학논문집
• /
• 제23권8호
• /
• pp.562-570
• /
• 2011

In this research, an experimental study is performed to investigate the effects of system operating variables on the cooling and heating characteristics of heat pump system using geothermal heat source and carbon dioxide as a refrigerant. System variables analyzed include compressor frequency, electronic expansion valve opening, refrigerant charge, secondary fluid temperature and flow rate. Results show that optimum refrigerant charge and electronic expansion valve opening position exist at the maximum point of COP curve, and both cooling and heating capacity increase but COPs decrease with the increase of compressor frequency. The change of a secondary fluid temperature leads to variation of overheat area and enthalpy difference in the evaporator and gas cooler. which again results in considerable variations of cooling and heating capacity and COP. In the case of effects of secondary water fluid flow rate, both cooling capacity and COP increase with the increase of secondary flow in evaporator or gas cooler, whereas heating capacity and COP decrease with the increase of flow rate in gas cooler.

• 설비공학논문집
• /
• 제20권11호
• /
• pp.711-717
• /
• 2008

Despite the fact that UFAD(Under Floor Air Distribution) systems have many benefits and are being applied in the field in increasing numbers, there is a strong need for an improved fundamental understanding of several key performance features of these systems. This study numerically investigates the effect of supplied air temperature and supplied flow rate on the performance of UFAD, especially focused on thermal comfort. Also this study has compared UFAD with conventional overhead air distribution system. In contrast to the well-mixed room air conditions of the conventional overheat system, UFAD system produces an overall floor-to-ceiling airflow pattern that takes advantage of the natural buoyancy produced by heat sources in the occupied zone and more efficiently removes heat loads and contaminants from the space. Thermal comfort parameters were evaluated by CFD approach and then PMV was computed to detect the occupants' thermal sensation. Results show that radiative mean temperature plays crucial role on the evaluating PMV. Until now, the radiative temperature has been the missing link between CFD and thermal comfort, but the present study paves the way for overcoming this weakness.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.484-492
• /
• 2012

The TMS(Thermal Management System) heater in a fuel cell vehicle has been developed to prevent a decline of fuel cell durability and cold start durability. Main functions of the COD(Cathode Oxygen Depletion) heater are depletion of oxygen in a cathode as heat energy and consumption of electric power for rapid warming up of a fuel cell stack. This paper covers subjects including the design specification of a heater, heater controller for detection of overheat and reliability assessment including coolant pressure cycle test of a heater. To verify the design concept, burst pressure and deformation analysis of plastic housing were carried out. Also, temperature distribution analysis of heater surface and coolant inside of housing were carried out to verify the design concept. By designing the plastic housing instead of a steel housing, the 30% weight lightening and 50% cost reduction were attained. A module-based design of a TMS system including a heater or reducing the watt density of a heater is a problem to be solved in the near future work.

• 한국환경복원기술학회지
• /
• 제15권1호
• /
• pp.63-71
• /
• 2012

To investigate the air temperature difference between windward and leeward side at high-rise building area, the air temperature and relative humidity data were observed for 10 minute interval from July 9, 2011 to November 30, 2011. The observed data were compared, analyzed and examined to illustrate air temperature between windward side (H Apartment) and Leeward side (W Apartment). The diurnal and seasonal variation of air temperature difference between windward and leeward site were also investigated. After the analysis, the overheat of windward side by $0.4^{\circ}C$ irrespective short distance of two observation positions. It was also lower than those of surrounding air temperature observing stations. It is mainly due to the air temperature decreasing effects of leeward side of high rise buildings.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.621-622
• /
• 2012

The thermal over-current relay or electronic motor protection relay is mostly used as the open-phase detection device of the three-phase motor or load. When the over-current or overheat of electric line is generated, it detects and operates circuit breaker, but there is the defect that the sensing speed is slow, the operation can be sometimes failed, and the precision is decreased. In order to improve these problems, this paper is proposed a new control circuit topology for open-phase protection using semiconductor devices. Therefore, the proposed open-phase protection device enhances the sensing speed and precision, and has the advantage of simple fitting in the three-phase motor control panel in the field, as it manufactures into small size and light weight.