• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.75-83
• /
• 2001

This paper presents the evaluation of combustion characteristics of sing-hole plasma jet ignitions in comparison with conventional spark ignition for variable of swirl velocity. Plasma jet plugs are three types according to ejecting directions : center of chamber, positive and negative swirl flow direction. Experiments are carried out for equivalent ratio 1.0 of LPG-air mixture in a constant volume cylindrical vessel. Not only the flame propagation is photographed at intervals, but the pressure variation in the combustion chamber is also recorded throughout the entire combustion process. The results show that the plasma jet ignitions and spark ignition enhance the overall combustion rate by increasing the swirl velocity. The dependence of the combustion rate swirl velocity leade to the conclusion that the placma jet plug, which ejects plasma jet to the cwnter of combustion chamber is the most desirable ignitor than other plugs.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.16-21
• /
• 2003

Natural gas is one of the promising alternative fuels because of the abundant deposits and the cleanness of emission gas. It can be used in conventional gasoline engine without major modification. Natural gas has some advantages than gasoline i.e. the high octane number, good mixing condition because of gas and wide inflamable limit. In the present study, a $1.8{\ell}$ conventional gasoline engine is modified for using the CNG as a fuel instead of gasoline. Performance and emission characteristics are compared between gasoline and CNG with 4 cylinder SI Engine which is controlled by programable ECU. Parameters of experimentation are equivalence ratio, spark timing and fuels. We analyzed the combustion characteristics of the engine using the cylinder pressure i.e. ignition delay, combustion duration and cycle variation. As a result, CNG engine shows lower exhaust emissions but brake torque is slightly reduced compared to gasoline engine. Overall combustion duration is longer than that of gasoline because of lower burning speed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2001.11a
• /
• pp.50-53
• /
• 2001

Flame propagation during the initial stages of ignition in a non-premixed swirl, having some of characteristics of the primary zone of an aero gas turbine combustor, has been investigated. Nd:YAG laser was adopted as the principal ignition source to allow arbitrary placing of the ignition site i subsequent flame development was monitored using a natural light high speed filming technique for many ignition site at two different swirl ratios and an overall equivalence ratio of 0.9. For ignition offset from the burner centreline, buoyancy force associated with radial pressure gradient produced a strong inward movement of the flame kernel. At the burner exit. flame kernels invariably developed into cylindrical form and a 'radial confinement /axia expansion' (RCAE) process was observed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.6
• /
• pp.1417-1431
• /
• 1994

In this study, shear strength characteristics of the Nak-Dong river sand in Taegu area are investigated by triaxial compression test, considering shear strain control velocity, relative density, and confining pressure. The results from Lade model and Modified Lade model are compared with the measured value in the laboratory test. The results by the change of shear strain control velocity, relative density, and confining pressure are as follows; 1) The stress limit, which can be Coulomb's law about the Nak-Dong river sand, have ranged 120~200 kpa at 0.08%/min and 120~150 kpa at 0.5%/min. These limits are smaller than that of the calcareous sand and the well-graded, quartz sand. 2) The parameters needed to Lade model and Modified Lade model are much affected by the strain control velocity and the relative density. Consequently, in the field, it is important to use parameters aptly after accurately understanding both the loading condition and subsoil condition. 3) Overall, the principal stress ratio obtained from constitutive model equations is not affected by the control velocity, but both the relative density and confining pressure affect the result of constitutive model equations. Consequently, the study on the various conditions about the relative density and confining pressure is needed to accurately predict the stress-strain behavior on the Nak-Dong river sand. 4) For the range of the used confining pressure in the study, the Lade model shows better agreements with the measured value than the Modified Lade model, comparing the measured value with the principal stress ratio at failure and the internal friction angle of failure envelope obtained from the Lade model and Modified Lade model.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.1 s.6
• /
• pp.43-50
• /
• 2000

Upgrade development of a high pressure ratio centrifugal compressor in marine engine turbochargers is presented. A new matched operating point at increased speed of rotation was determined through system cycle analysis using the exisitng test data of turbine performance. Under some severe restrictions for geometric parameters, the state-of-the-art methods of both aerodynamic design and CFD analysis were applied, in which only an impeller, a vaned diffusor and some part of casing wall were modified. Prototype hardware was fabricated and assembled for system performance tests. Excellent performance in pressure ratio and efficiency was obtained over whole speed region. Reduced surge and choke margin was, however, observed at design speed of rotation.

• Journal of ILASS-Korea
• /
• v.10 no.2
• /
• pp.1-9
• /
• 2005

An experimental study was carried out to obtain the fundamental data about the effects of radical ignition on premixture combustion. A CVC(constant volume combustor) divided into the sub-chamber and the main chamber was used. Numerous narrow passage holes are arranged between the main chamber and the sub-chamber. The products including radicals generated by spark ignition in tile sub-chamber derives the simultaneous multi-point ignition in the main chamber. We have examined the effects of the sub-chamber volume, the diameter and number of passage holes, and the equivalence $ratio({\Phi})$ on the combustion characteristics by means of burning pressure measurement and flame visualization. In a CVC, the overall burning time including the ignition delay became very short and the maximum burning pressure was slightly increased by the radical ignition(RI) method in comparison with those by the conventional spark ignition(SI) method. Combustible lean limit by RI method is extended by ${\Phi}=0.25$ compared with that by SI method. Also, In cases of charging the number and the diameter for the fixed total cross section of the passage holes, combustion period increased significantly at a sub-chamber with a single hole, but those of the other conditions had almost a similar tendency in the sub-chamber with 4 or more holes. regardless of equivalence ratio. Therefore, it was Proved that a critical cross section exists with the number of passage holes.

• Fashion & Textile Research Journal
• /
• v.21 no.3
• /
• pp.336-345
• /
• 2019

This study evaluated the preference and wearing characteristics of existing fitness compression wear for elderly women and identified the problems and improvements of existing fitness apparel. Preference and wearing characteristics for 6 types (A-F) of upper and lower fitness compression wear were evaluated. Photos and drawings as well as the preferred designs and details were investigated after presenting the evaluation clothing. Evaluations were made on a 5 point Likert scale for the fitness, allowance, pressure, ease of movement, fabric material, and overall satisfaction after wearing. The design preference indicated that B type (26.6%) and C type (23.4%) were preferred in the top with C, E and F type preferred to the same ratio of 19.4% in the slacks. The fitness and allowance amount of the top B type were the most appropriate (${\geq}4$), the C type was in close contact (2.86), and the F type was inadequate in the neck circumference (1.77). The feeling of pressure was high in the waist, abdomen, thighs, and knees. The area where the elderly people want to improve their strength was the legs; in addition, a pattern design was needed to strengthen leg muscles when designing fitness compression wear. However, a design with excessive adhesion due to a muscle support band was shown to be not preferred. Therefore, depending on the activity, it is necessary to develop a fitness compression wear that applies an optimum stretching ratio of fabric based on body surface area changes.

• Fisheries and Aquatic Sciences
• /
• v.25 no.2
• /
• pp.101-116
• /
• 2022

The harvesting season of lompa fish, Thryssa baelama, through sasi, indigenous knowledge in resources management, in Haruku Village has become a socio-cultural event that attracts many people. The sasi of lompa fish has been conducted for hundreds of years. Information on the bioecology aspect of lompa fish is limited, while this information is crucial for lompa fish sustainability through the sasi approach. This study aimed to investigate some population parameters of lompa fish, its sustainability status, and proposed a sustainable management strategy for the lompa fishery of Haruku Village. Fish population parameter covers length-weight relationship, growth pattern, size distribution, sex ratio, and the body condition index. The sustainability status was assessed following the Rapfish approach. Fisheries management strategy was performed using a conceptual model framework based on Driver Pressure State Impact Response. The research shows that the total length varies between 9.2-14.3 cm. A high relationship was found between total length and weight, and the growth pattern was an allometric negative. There was a difference in sex ratio between males and females, with females dominant. The body condition index varies over time, probably due to reproductive status. The overall sustainability status was at fair condition (61.60%), with the ecological domain having the highest sustainable status (71.07%) and considered sustain. In comparison, the technological domain had the lowest sustainability status (52.58%) and was considered fair sustain. There were seven management strategies proposed for sustainable management for the lompa fishery.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.524-531
• /
• 2004

To investigate relevance of the definition of the reference stress to estimate J and $C^{*}$ for surface crack problems, this paper compares FE J and $C^{*}$ results for surface cracked pipes with those estimated according to the reference stress approach using various definitions of the reference stress. Pipes with part circumferential inner surface crack and finite internal axial crack are considered, subject to internal pressure and global bending. The crack depth and aspect ratio are systematically varied. The reference stress is defined in four different ways using (i) the local limit load, (ii) the global limit load, (iii) the global limit load determined from the FE limit analysis, and (iv) the optimized reference load. It is found that the reference stress based on the local limit load gives overall excessively conservative estimates of J and $^{*}$. Use of the global limit load clearly reduces the conservatism, compared to that of the local limit load, although it can provide sometimes non-conservative estimates of J and $^{*}$. The use of the FE global limit load gives overall non-conservative estimates of J and $^{*}$. The reference stress based on the optimised reference load gives overall accurate estimates of J and $^{*}$, compared to other definitions of the reference stress. Based on the present finding, general guidance on the choice of the reference stress for surface crack problems is given.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.759-767
• /
• 2003

This paper presents the simplified but more rational analysis method for the prediction of additional internal forces induced in integral abutment bridges. These internal forces depend upon the degree of restraint provided tc the deck by the backfill soil adjacent to the abutments and piles. In addition, effect of the relative flexural stiffness ratio among pile foundations, abutment, and superstructure on the structural behavior is also an important factor. The first part of the paper develops the stiffness matrices, written in terms of the soil stiffness, for the lateral and rotational restraints provided by the backfill soil adjacent to the abutment. The finite difference analysis is conducted and it is confirmed that the results are agreed well with the predictions obtained by the proposed method. The simplified spring model is used in the parametric study on the behavior of simple span and multi-span continuous integral abutment PSC beam bridges in which the abutment height and the flexural rigidity of piles are varied. These results are compared with those obtained by loading Rankine passive earth pressure according to the conventional method. From the results of parametric study, it was shown that the abutment height, the relative flexural rigidity of superstructure and piles, and the earth pressure induced by temperature change greatly affect the overall structural response of the bridge system. It may be possible to obtain more rational and economical designs for integral abutment bridges by the proposed method.