• 전력전자학회논문지
• /
• 제22권4호
• /
• pp.369-372
• /
• 2017

This paper presents a control scheme for three-level NPC inverters using small DC-link capacitors. To reduce the inverter system volume, the film capacitor with small capacitance is a promising candidate for the DC-link. When small capacitors are applied in a three level inverter, however, the AC ripple component increases in the DC-link NPV (neutral point voltage). In addition, the three-phase input grid currents are distorted when the DC-link capacitors are fed by diode rectifier. In this paper, the additional circuit is applied to compensate for small capacitor systems defect, and the offset voltage injection method is presented for the stabilization in NPV. These two proposed processes evidently ensure the quality improvement of the input grid currents and output load currents. The feasibility of the proposed method is verified by experimental results.

• 한국통신학회논문지
• /
• 제34권7A호
• /
• pp.568-573
• /
• 2009

본 논문에서 0.13um CMOS 공정으로 설계된 배터리 기반 휴대용 통신 시스템 구동용의 온칩 시동회로를 갖는 스텝다운 CMOS DC-DC 변환기를 제안하였다. 1MHz의 스위칭 주파수를 기반으로 설계된 벅 변환기에는 온칩 시동회로와 커패시터 멀티플라이어 기법을 이용한 보상회로를 포함시켰다. 칩 측정 결과 2.5V ${\sim}$3.3V의 입력 전압을 1.2V로 강압시키는데 최대 87.2%의 효율을 갖는다. 최대 부하 전류, 출력 전류 리플 및 전압 리플은 각각 500mA, 25mA, 24mV 이다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1297-1300
• /
• 2008

A conventional linear accelerator system requires a flat-topped pulse with less than ${\pm}$ 0.5% ripple to meet the beam energy spread requirements and to improve pulse efficiency of RF systems. A pulse transformer is one of main determinants on the output pulse voltage shape. The pulse transformer was investigated and analyzed with the pulse response characteristics using a simplified equivalent circuit model. The damping factor ${\sigma}$ must be >0.86 to limit the overshoot to less than 0.5% during the flat-top phase. The low leakage inductance and distributed capacitance are often limiting factors to obtain a fast rise time. These parameters are largely controlled by the physical geometry and winding configuration of the transformer. A rise time can be improved by reducing the number of turns, but it produces larger pulse droop and requires a larger core size. By tradeoffs among these parameters, the high-voltage pulse transformer with a pulse width of 10 ${\mu}s$, a rise time of 0.84 ${\mu}s$, and a pulse droop of 2.9% has been designed and fabricated to drive a klystron which has an output voltage of 284 kV, 30-MW peak and 60-kW average RF output power. This paper describes design optimization of a high-voltage pulse transformer for high-power pulsed applications. The experimental results were analyzed and compared with the design. The design and optimal tuning parameter of the system was identified using the model simulation.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 추계학술대회
• /
• pp.398-401
• /
• 2011

본 논문에서는 고효율의 CMOS PWM DC-DC 벅 변환기를 설계하였다. 설계된 CMOS PWM DC-DC 벅 변환기는 입력전압(3.4-3.9V)로부터 일정한 출력전압(1-2.8V)을 생성한다. Inductor-based 방식을 택하였고, 제어 대상은 전류이며, Pulse Width Modulation(PWM) 모드로 동작한다. 회로 구성은 Power Switch, Pulse Width Generation, Buffer, Zero Current Sensing, Current Sensing Circuit, Clock & Ramp generation, V-I Converter, Soft Start, Compensator, Modulator 등 이다. 제안된 CMOS PWM DC-DC 벅 컨버터는 Switching Frequency가 약 1MHz이고, 부하 전류가 약 40mA이상부터 CCM동작을 하며 100mA일 때 98.71%의 최대 효율을 갖는다. 또한, 출력전압 리플은 0.98mV이다(입력전압 3.5V, 출력전압 2.5V 기준). 제안된 회로의 검증을 위해 CMOS $0.18{\mu}m$ 공정을 이용하여 시뮬레이션을 수행하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1041-1044
• /
• 1992

A solar cell should be operated at the maximum output point on the I-V characteristic curve with constant current and constant voltage in order that the solar energy be fully utilized. According to, in this paper, we describes a controller which can track the maximum power point of a solar arry using current and voltage ripple variation of step up chopper system. The control circuit is desinged such that actual current and voltage are sensed directly from the solar cell array. These two signal are then holded sampling and multiplies by a single chip multiplier.

• 전력전자학회논문지
• /
• 제20권3호
• /
• pp.280-289
• /
• 2015

A high-efficiency full-bridge DC-DC converter with a current-doubler rectifier and an asymmetric pulse-width modulation is proposed. Through the asymmetric pulse-width modulation, the proposed converter achieves zero-voltage switching of power switches without the circulating currents. The proposed converter reduces the output current ripple through the current-doubler rectifier. A control strategy is suggested for the proposed converter to charge battery banks. A constant current and constant voltage charging is performed. The proposed converter achieved a higher efficiency compared with the conventional full-bridge DC-DC converter with a phase-shift modulation. The performance of the proposed converter is evaluated by the experimental results for a 1.0 kW prototype circuit.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.42-44
• /
• 2005

The motor research of pre-existing attaches importance about one and three motor of reduce torque ripple and speed control. 3-Phase PMSM Motor, which is generally used, has limited usage in high speed, due to pulsation torque and variable speed. To solve this problem it is necessary to increase invariable, pole number or the number of slots. In this paper 7-Phase PMSM Motor of Steady state analysis of Torque and Output Voltage characteristic.7-Phase modulation method with Space Voltage Vector is studied for ideal operation of controller.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.31-35
• /
• 2003

This paper presents a microprocessor controlled digital ballast for HID lamps, which gives intelligent features such as a precise power control, optimum ignition voltage and detection of end of life. Average current mode PFC is employed for reducing EMI and a universal input. Direct spread spectrum is done by applying 1 KHz triangular wave for removing acoustic resonance. This frequency modulation of 1 KHz gives also low EMI level and no ripple on lamp current. The microprocessor controls the voltage of DC-bus, the voltage of ignition pulses, the power of output and the bandwidth of spread spectrum. A 250W digital ballast is implemented with an efficiency of 93％ and a maximum EMI level of 55 ㏈${\mu}$V.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.191-192
• /
• 2014

Multiple output converters (MOCs) are widely used for applications which require various levels of the output voltages due to their benefits in cost, volume, and efficiency. However, most of the MOCs developed so far can regulate only one output tightly and require as many secondary windings in the transformer as the number of the outputs. In this paper, a novel Time Division Multiple Control (TDMC) method to regulate all the outputs in high precision is proposed and applied for the multiple output battery charger based on the phase shift full bridge topology to charge a multiple number of batteries at one time. The proposed converter can charge three different kinds of batteries or same kind of batteries in different state of charges (SOCs) by using constant current/constant voltage (CC/CV) charge mode independently. At the same time it can provide an even degree of tight regulation for each output to satisfy the strict ripple requirement of the battery. The validity and feasibility of the proposed method are verified through the experiments.

• Journal of Electrical Engineering and Technology
• /
• 제11권6호
• /
• pp.1634-1644
• /
• 2016

In this paper, a current-fed two-inductor bi-directional DC/DC converter using resonance (CF-TIBCR) and its design method are proposed. The CF-TIBCR has characteristics of low current ripple and a high current rating because of two separated inductors. Also, it achieves zero voltage switching for all switches and zero current switching for switches of a low voltage stage by using the resonant tank. Besides, a voltage spike problem in conventional current-fed converters is solved without the need for an additional snubber or clamping circuits. As a result, the CF-TIBCR features high step-up and high efficiency. Since the proposed converter has difficulty achieving the soft-switching condition when the converter requires the low voltage transfer ratio, a method that varies the number of resonant cycles is adopted to extend the output voltage range with satisfying the soft-switching condition. The principles of the operation characteristics are presented with a theoretical analysis, and the proposed converter is verified through results of an experiment using a laboratory prototype.