• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6A
• /
• pp.853-859
• /
• 2008

As a new system of steel pipe pile cap reinforcement, the application of perforated flat bar bolted to the steel pipe pile head was suggested for the improvement of structural performance of footing structure. This study investigates the structural characteristics of perforated flat bar shear connectors according to shape and diameter of hole, number of rebars passing through the hole and the depth of settlement. The result shows several requirements to ensure sufficient pull-out resistance and ductility such as that the hole diameter excluding diameter of rebar should exceed the size of aggregates; the hole should be perforated with diameter as the half of plate height; and the adequate depth of settlement should be ensured for the optimal performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.920-928
• /
• 2003

The objective of the present study was to investigate the characteristics of flow and wall shear stress under steady and pulsatile flow in the aneurysm. The numerical simulation using the software were carried out for the diameter ratios ranging from 1.5 to 3.0, Reynolds number ranging from 900 to 1800 and Womersley number, 15.47. For steady flow, it was shown that a recirculating vortex occupied the entire bulge with its core located closer to the distal end of the bulge and the strength of vortex increased with increase of the Reynolds number and diameter ratio. The position of a maximum wall shear stress was the distal end of the aneurysm regardless of the Reynolds number and diameter ratios. For the pulsatile flow, a recirculating flow at the bulge was developed and disappeared for one period and the strength of vortex increased with the diameter ratio. The maximum values of the wall shear stress increased in proportion to the diameter ratio. However, the position of a maximum wall shear stress was the distal end of the aneurysm regardless of the diameter ratios.

• Korean Journal of Medicinal Crop Science
• /
• v.17 no.6
• /
• pp.452-457
• /
• 2009

This study was carried out to investigate the correlation between root diameter and ginsenoside composition of Panax ginseng C. A. Meyer cultivar Yunpoong. Dry matter ratio of main root was a little higher than that of lateral root and fine root, and that was higher by the increase of root diameter in the same root parts. Total ginsenosides composition of main and lateral roots increased by the decrease of root diameter, especially in lateral root. Similar resulted in fine root, but there was no significant difference where root diameter was below 2.5 mm. Except for ginsenoside-$Rg_1$, other ginsenosides component, PDs, PTs and total ginsenosides had highly negative correlation with the root diameter within whole root, main root+lateral root and lateral root+fine root, while $Rg_1$ had positive correlation with the root diameter.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.171-178
• /
• 2006

The sonication mettled is widely used with surfactants to suspend individual single-walled carbon nanotubes in solution, and it is well known that sonication-induced tube cutting occurs. Recently, it is found out that ultrasonicated nanotubes yield simultaneous separation by tube length and diameter. Nanotubes that have been cut shortest possess the greatest enrichments of large-diameter species. In this study, single-walled carbon nanotubes are cut using a ball milling method. Similar fracture behavior is observed fur the ball milled nanotubes: i.e., large diameter tubes are cut shorter. The ability to separate carbon nanotubes by diameter and length will contribute to tile development of nanotube-based applications.

• Journal of the Korea Furniture Society
• /
• v.17 no.4
• /
• pp.109-114
• /
• 2006

An investigation was carried out for the annual ring width, longitudinal tracheid diameter and wall thickness in different tree heights for Pinus koraiensis Sieb. et. Zucc. The annual ring width increased along with the tree height, however the tracheid diameter and wall thickness decreased with the tree height. Tracheid wall thickness was found the thickest at 2.0m from the above ground samples and it increased gradually from pith to bark. Radial tracheid diameter was found to be larger than that of tangential tracheid diameter in earlywood. But, it was found to be the opposite in latewood. In earlywood, the average values of tracheid wall thickness was found the range of $2.1-3.0{\mu}m$, whereas, in latewood, it was $2.4-4.2{\mu}m$.

• Journal of Korean Society of Forest Science
• /
• v.3 no.1
• /
• pp.15-17
• /
• 1963

1) An experiment was made at the newly constructed glass house of Chun chan Agriculture callege to find out facts about the late-raising of Cortinellus edodes (Berk) Ido et Imai during the winter season. 2) The host timbers used in this experiment were Quercus Serrata Thumb and Quercus crispulo BI.; 5 years old each, the diameter ranging from 6cm to 17cm, dividing them into 12 diameter groups with 10 timbers in each group. The total number of timbess was 240 in two blocks. 3) As the pre-treatment of host timber, the autumn generation in 1962 was inhibited, and before being put into the glass-house, they were stimulated of generation for 3 days after 3 days, water-soaking. 4) The temperature control was made by using two coal stoves and the humidity control by spraying and two full water tanks. During cloudy weather and night, the green house was covered to preserue constant temperature of $5^{\circ}C{\sim}10^{\circ}C$. 5) The result; Quercus Serrata Thumb. with lesser diameter than 9cm showed no generation either in as big timber as one with diameter 11 cm. On the other hand, too big timbers showed low rate of generation; the reason, at a guess, is the too short period of cultivation and insufficient water soaking and inappropriate temperature. 6) The most standard size of host timber was found out be those with diameter 12cm~15cm in Quercus serrata Thumb, and those with diameter 14cm~17cm in Quercus crispula BI. Quercus crispula seemed to have slightly greater efficiency of generation than Quercus Serrata Thumb., but it could not be concluded as "decisive". Lastly, the host timber used in this experiment were old and the rate of generation was low as a whole.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.560-565
• /
• 2001

The objective of the present study is to investigate the characteristics for flow and wall shear stress in the aneurysm which is a local dilatation of the blood vessel. The numerical simulation using the commercial software for the laminar and steady flow were carried out over the diameter ratios(ratio of maximum diameter of aneurysm to the diameter of blood vessel) ranging from 1.5 to 2.5 and Reynolds number ranging from 900 to 1800. It was shown that a recirculating vortex occupied the entire bulge with its core located closer to the distal end of the bulge and the strength of vortex increased with increase of the Reynolds number and diameter ratio. Especially, for the Reynolds number of 1800 and diameter ratio of 2.5, the very weak secondary recirculating flow was produced at the left upper of the aneurysm. The position of a maximum wall shear stress was the distal end of the aneurysm(z=18mm) regardless of the Reynolds number and diameter ratios. But the maximum values of the wall shear stress increased in proportion to the increase of Reynolds number and diameter ratio.

• Journal of the Korea Furniture Society
• /
• v.22 no.1
• /
• pp.18-25
• /
• 2011

This experiment was carried out to investigate the effects of nail diameter, driving distance from end on the nail check length, and the effects of nail diameter, prehole for nail driving, and nail driving slope on the nail withdrawal resistance, by the static test of universal testing machine. The test specimen were Japanese cedar (Cryptomeria japonica D. Don.) boards grown in southern district of Korea, and the nails for test were 2.02～4.82 mm in diameter. After nail driving, the back face checks of test boards were longer than the surface checks. The optimum nail diameter without checks or loss of nail withdrawal resistance were below 10% of board width and the optimum driving distance from end of boards were ten multiple of nail diameter. The relation between nail diameter (x) and withdrawal resistance (y) was linear and the regression formulae for Japanese cedar board was y = 8.66x + 7.6 ($R^2=0.978$). As both of the prehole diameter and driving slope were increased, the withdrawal resistances were significantly decreased.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.944-955
• /
• 2009

In this thesis the model tests were performed to the pull-out characteristics of a suction pile subjected to a pull-out in sands. For this model tests, three different soil conditions ($D_r$=45, 65, 82%), three pile diameters (D=100, 150, 200mm) and three pile lengths (L=100, 150, 200mm), were changed. And the experimental results were also compared with those by the theoretical methods. The results by the experimental and theoretical analysis are as follows. The ultimate pull-out resistances increased as the relative density of sands, pile diameter, length and the ratio of pile length to diameter increased. The ultimate pull-out resistance by Meyerhof method(1973) overestimated that by the model test, but the results using the soil-pile friction angle suggested by Aas(1966) in the Meyerhof(1973) method were in good agreement with the experimental results.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.55-62
• /
• 2004

This paper addresses the method for figuring out the hole diameter on the mask containing the information about machining depth. With this mask e micro machining is carried out with a simple 2D movement of the mask. Based on e suggested method excimer laser ablation processes are modeled and determination of the optimal laser ablation conditions such as hole diameter, step size, mask movement velocity, etc. is completed. The excimer laser ablation simulation for creating 3D micro lens is carried out by employing determined ablation conditions to prove verification of the method. The results from simulation illustrated the average error of 140nm and e relative error of 2％.