채굴적에 의한 지표에서의 지반침하발생 위치를 추정함에 있어, 절리군은 필수적으로 고려되어야하는 요소 중의 하나인 바, 각 절리군의 역학적 특성과 이들이 채굴적 상부 암반에 분포하는 양상은 지반침하발생을 가속시킬 수 있다. 따라서 본 연구에서는 침하발생 범위의 추정에 관한 선행연구의 근거자료로 이용된 자료 중 절리군의 방향성에 대한 조사정보의 신뢰성이 비교적 양호한 자료들을 선별하여 절리군의 방향성을 중심으로 지반침하 발생위치와의 상관관계를 재검토하였으며, 추정각과 침하 지역에 분포하는 주절리군 $J_1$의 경사각을 비교하여 주절리군 $J_1$이 침하에 미치는 영향을 분석하였다.
본 논문은 절리암반 터널의 안정성 해석을 위한 2차원 개별요소모델링방법에 대한 개선방안을 제안하였다. 먼저, 절리군과 터널의 상대방위를 고려하여 터널단면상에서 불연속거동이 가능한 절리군을 구별하는 기준을 제시하였다. 이 기준에 따라 불연속거동이 가능한 절리군은 개별요소(암석블록)의 변이 되도록 하고 그 외 절리군은 암석블록의 탄성특성을 보정하는 방법을 제시하였다. 또한, 주어진 절리의 기하학적 특성에 대해서 절리의 방위편차와 유한길이를 고려한 복잡한 모델과 절리의 평균방위와 무한길이를 고려한 단순한 모델의 특성을 분석하였다. 그 결과, 후자의 모델이 일관성 있는 터널의 국부적 파괴양상과 명료한 암반의 불연속거동을 보여줌으로써 터널설계목적에 적절함을 확인하였다.
암반구조물 설계를 위한 지반조사에서 지하 암반에 분포된 불연속면들의 방향성 파악은 시추공 내부에 대한 영상촬영 기법에 전적으로 의존되어 왔다. 그러나, 공내 영상촬영은 고가의 장비가 요구되며 시추작업 완료 후 측정작업이 추가로 소요되어 극히 제한적으로 수행되고 있다. 본 연구에서는 시추조사시 간편하게 불연속면의 방향을 측정하여 신뢰성 있는 지반정보 자료를 제공할 수 있는 Discontinuity Orientation Measurement (DOM) 시추장비 및 불연속면 분포해석 모델 RoSA-DOM을 개발하였다. DOM 시추 장비에서 기 설정된 방향성을 지시하는 기준선이 표시된 시추 코어가 회수되면 코어 상의 절리 단면에서 측정된 3개 지점의 자표를 이용하여 절리면의 경사방향 및 경사각을 산정한다. 또한 코어 축이 절리면을 관통하는 지점의 좌표를 산정하여 절리 위치를 설정한다. 절리군 형성은 clustering algerian을 활용하여 분석한다. 코어 축을 조사선으로 설정하여 전체 절리 간격 및 군 간격을 해석한다. 전체 시추구간 및 특정 구역에서의 RQD를 산정하여 암반의 공학적 활용도 고찰을 위한 기본 자료를 도출한다.
Stereographic method is a general and basic method to analyse sliding failure potential of rock slope. Region of failure analysis using stereographic method extend to curved slope from straight slope in this paper, Curved slope is defined as the multi-face slope with free surface more than two face and has different characteristics from straight single face slope. Individual daylight envelopes of free surfaces are combined into total daylight envelope of multi-face slope. So, sliding envelope of multi-face slope is the daylight envelope except friction cone. Specially, If only single joint set is developed in the slope, single plane sliding(or plane failure) is impossible in the single-face straight slope, but possible in the multi-face slope. In the multi-face slope with only one joint set, single plane sliding occurs when orientation of sliding plane is between two side slope orientation in the sliding envelope.
This paper presents some proposed methods for discontinuum analysis with rock discontinuities data acquisited in tunnel design stage. The limit equilibrium method for rock block sliding and falling proposed in this paper can consider the tunnel excavation and support stage, and, to the extent, the standard deviations and means of joint set orientation. Simple Distinct Elemet modelling methods are recommended in estimating the stability of tunnels in jointed rock masses. Because, the simple models are likely to show more consistent and clear than very complex model with finite joint length and joint deviation parameters.
터널이나 사면과 같은 암반 구조물의 거동은 불연속면에 의해 지배적인 영향을 받는다. 따라서 암반내 존재하는 불연속면 자료의 조사 및 분석은 암반구조물 설계 및 시공에 있어서 상당히 큰 중요성을 가진다. 이러한 불연속면의 조사 및 분석 작업 중에서 반드시 거처야 할 작업 중 하나가 절리군을 분별하는 것이다. 기존의 절리군 분석 작업은 대부분 시각적인 방법으로 행해지고 있다. 이 경우 분석자의 주관에 따라 차이를 보일 수 있으며 절리의 방향 정보 외의 다른 추가적인 정보들은 사용하기 힘든 단점이 있다. 본 연구에서는 절리군 분석을 돕기 위하여 퍼지 클러스터링 기법을 이용한 프로그램을 개발하였으며 이를 두 가지 형태의 절리 자료에 대한 절리군 분석에 적용하였다. 적용 결과 퍼지 클러스터링 기법이 다수의 절리 자료에 대한 절리군 분석, 평균방향 및 밀집도 추정에 효과적이며 타당한 방법임을 확인하였다.
A robotic sapatial augmented reality (RSAR) system, which combines robotic components with projector-based AR technique, is unique in its ability to expand the user interaction area by dynamically changing the position and orientation of a projector-camera unit (PCU). For a moving PCU mounted on a conventional robotic device, we can compute its extrinsic parameters using a robot kinematics method assuming a link and joint geometry is available. In a RSAR system based on user-created robot (UCR), however, it is difficult to calibrate or measure the geometric configuration, which limits to apply a conventional kinematics method. In this paper, we propose a data-driven kinematics control method for a UCR-based RSAR system. The proposed method utilized a pre-sampled data set of camera calibration acquired at sufficient instances of kinematics configurations in fixed joint domains. Then, the sampled set is compactly represented as a set of B-spline surfaces. The proposed method have merits in two folds. First, it does not require any kinematics model such as a link length or joint orientation. Secondly, the computation is simple since it just evaluates a several polynomials rather than relying on Jacobian computation. We describe the proposed method and demonstrates the results for an experimental RSAR system with a PCU on a simple pan-tilt arm.
Determination of the mechanical behaviour of jointed rock masses has been a challenge for rock engineers for decades. This problem is more pronounced for non-persistent jointed rock masses due to complicated interaction of rock bridges on the overall behaviour. This paper aims to study the effect of a non-persistent joint set configuration on the mechanical behaviour of rock materials under both uniaxial and biaxial compression tests using a discrete element code. The numerical simulation of biaxial compressive strength of rock masses has been challenging in the past due to shortcomings of bonded particle models in reproducing the failure envelope of rock materials. This problem was resolved in this study by employing the flat-joint contact model. The validity of the numerical model was investigated through a comprehensive comparative study against physical uniaxial and biaxial compression experiments. Good agreement was found between numerical and experimental tests in terms of the recorded peak strength and the failure mode in both loading conditions. Studies on the effect of joint orientation on the failure mode showed that four zones of intact, transition to block rotation, block rotation and transition to intact failure occurs when the joint dip angle varies from 0° to 90°. It was found that the applied confining stress can significantly alter the range of these zones. It was observed that the minimum strength occurs at the joint dip angle of around 45 degrees under different confining stresses. It was also found that the joint orientation can alter the post peak behaviour and the lowest brittleness was observed at the block rotation zone.
시추공 텔레뷰어에 의해 획득된 시추공벽 영상을 이용하여 암반내 절리 구조 특성을 해석하고자 하였다. 절리구조의 특성으로서 발달된 절리군의 방향성 및 거칠기의 산정은 영상분석을 통한 절리궤적의 추적에 의하였으며, 산정된 절리군의 JRC 값과 추정된 역학적 상수들로부터 Barton-Bandis 모델에 의해 절리강성을 추정하고 자료들을 종합하여 암반 수치해석 모델링용 절리구조도를 작성하였다. 시추공벽 절리궤적의 추적 효율성을 높이기 위하여 영상 분석기에 내장된 함수를 이용한 최적의 매크로 프로그램과 걸칠기 산정 프로그램, 절리구조도 작성용 프로그램을 완성하였다.
암반 불연속면의 조사 및 분석 과정에서 거쳐야할 필수적인 단계 중 하나는 방대한 불연속면 자료로부터 군을 판별하는 것이다. 불연속면 군 분류는 암반분류, 키블록 해석. 개별요소해석 및 불연속연결망 생성과 같은 암반공학적 업무에 있어서 필수적이다. 일반적으로 등고선도를 이용한 수작업 군 분류가 적용되었으나 이 방법은 수작업에 의존한 주관적인 결과를 제공한다는 단점이 있다. 본 연구에서는 유전자알고리즘을 이용한 불연속면 군 분석기법을 도입하였으며 방향성 자료에 적용하기 위해 기본적인 유전자알고리즘을 변경하였다. 최종적으로 이러한 이론을 적용한 FORTRAN 프로그램 GAC를 개발하였으며 두 가지 형태의 불연속면 자료의 군 분석에 적용하였다. 적용 결과 GAC를 적용한 군 분류는 빠르고 효율적인 군 분석방법임을 확인하였으며 최적의 불연속면 군 수를 결정하는 데 있어서 분산에 근거한 적합도 함수가 Davis-Bouldin 지수에 근거한 적합도 함수보다 효율적인 것으로 나타났다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.