• 한국정밀공학회지
• /
• 제15권12호
• /
• pp.97-105
• /
• 1998

The fiber oriented condition inside fiber reinforced composite material is a basic factor of mechanical properties of composite materials. It is very important to meausure the fiber orientation angle for the determination of molding conditions, mechanical characteristics, and the design of composite materials. In the work, the fiber orientation distribution of simulation figure plotted by PC is measured using image processing in order to examine the accuracy of intersection counting method. The fiber orientation function measured by intersection counting method using image processing is compared with the calculated fiber orientation function. The results show that the measured value of fiber orientation function using intersection counting method is lower than the calculated value, because the number of intersection between the scanning line and the fiber with smaller fiber aspect ratio is counted less than with larger fiber aspect ratio.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 1988년도 학술발표초록집
• /
• pp.35-37
• /
• 1988

This paper shows the possibility of the application of the orientation density function of fibers to the mechanics of fibrous assembly. As an example, the orientation density function of a single yarn was theoretically derived in consideration of the idealized helical yarn. And the theoretical derivation of the tensile modulus of the fibrous assembly was performed in view of the fiber orientation. Application of this orientation density function to the obtained tensile modulus and to the contraction factor of the yarn was also performed so that the theoretical equations of the tensile modulus and the contraction factor of the yarn were obtained. Close agreement was shown between the theoretical and the existing equations. Consequently it was confirmed that the application of the orientation density function to the mechanics of the fibrous assembly is sufficiently possible.

• 한국정밀공학회지
• /
• 제13권6호
• /
• pp.34-44
• /
• 1996

In order to examine the accuracy of the intensity method, the fiber orientation-angle distribution of fiber-reinforced polymeric composites is measured using image processing. The fiber orientation function is calculated from the fiber orientation measured by the soft X-ray photograph. Theoretical and experimental results of fiber orientation function are compared for the composites with different fiber contents and fiber orientations. The intensity method is used for the experimental investigation and the measured fiber orientation function is compared to the calculated one. The relations between the measured and the simulated fiber orientation functions $J{\small{M}}$ and $J{\small{S}}$ respectively are identified. For the fiber length of 1.000mm and 2.000mm, it shows that $J{\small{M}}=0.83J{\small{M}}$. However. in general. the value of $J{\small{M}}$ decreases as the fiber length increases. For GFRP composites the relations between $J{\small{M}}$ and theoretical value J show that $J{\small{M}}$=0.73J for short fiber and $J{\small{M}}$=0.81J for long fiber.

• 한국정밀공학회지
• /
• 제10권2호
• /
• pp.104-113
• /
• 1993

Characteristics of fiber-reinforced thermoplastic sheet depend on the quantity and shape of fibers. During a molding process of composites, the fiber-maxtrix separation and fober orientation are caused by the flow during the molding process. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation-orientation and molding conditions. The correlation between the separation and the orientation have to be clarified for designing the fiber structure. In this paper, the degree of nonhomogeneity which is a measure of the separation is obtained using one-dimensional rectangular shaped part compression molding. And the orientation function is defined and measured by the image processing using soft X-rayed photograph and image scammer. Correlation between the degree of nonhomogeneity and the orientation function is discussed.

• International journal of advanced smart convergence
• /
• 제7권2호
• /
• pp.1-6
• /
• 2018

In this paper, we propose an automatic left ventricle segmentation method in computed tomography angiography (CTA) using separating energy function. First, we smooth the images by applying anisotropic diffusion filter to remove noise. Secondly, the volume of interest (VOI) is detected by using k-means clustering. Thirdly, we divide the left and right heart with split energy function. Finally, we extract only left ventricle from left and right heart with optimizing cost function including orientation term.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.953-959
• /
• 1998

To investigate accuracy of intensity method for measurement of the fiber orientation distribution, fiber orientation function is calculated by drawing simulation figures for the fiber orientation as varying fiber aspect ratio, fiber area ratio, and fiber orientation state, respectively. The values of fiber orientation function measured by intensity method are compared with the calculated values of fiber orientation function. The results show that measurement accuracy of the fiber orientation angle distribution by intensity method is affected by the fiber aspect ratio when the total length of oriented fiber is same. The average gradient of fiber orientation function is 0.94 for 1000mm of the total fiber length and is 0.93 for 2000 mm when the fiber aspect ratio is over 50. Measurement accuracy by intensity method is about 94% and the reliable data can be obtained by intensity method.

• 한국해양공학회지
• /
• 제9권2호
• /
• pp.123-132
• /
• 1995

During compression molding of fiber-reinforced polymeric composites, microstructural changes such as the fiber-matrix separation and the fiber orientation are occurred by the flow of composite materials. Since the nonhomogeneity and anisotropy of composites are caused by the separation and orientation of fibers. On the other hand, the separation and the orientation of fibers are inseparably related to each other. In this paper the degree of nonhomogeneity which is a measure of the separation is obtained using one-dimensional rectangular shaped part compression molding. And the orientation function is measured by the image processing using soft X-rayed photograph and image scanner. We study effects of the mold temperature on the degree of nonhomogeneity and the orientation function.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.659-663
• /
• 1995

The fiber oriented conditied inside fiber reinforced composite material is a basic factor of mechanical properties of composite materials. It is very important to measure the fiber orientation angel for the determination of molding conditions, mechanical charactistics, and the design of composite materials. In the work, the fiber orientation distribution of simulation figure plotted by PC is measured using image processing in order to examine thr accuracy of intersection counting method. The fiber orientation function measured by intersection countingmethod using image processing is compared with the calculated fiber orientation function. The results show that the measured value of fiber orientation function using intersection counting method is lower than the calculated value, because the number of intersection between the secant line and the fiber with smaller fiber aspect ratio is counted less than with larger fiber aspect ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.186-191
• /
• 2004

we can say that the increasing range of the value of GMT Sheet's tensile strength in the direction of fiber orientation is getting wider as the fiber content increases. It shows that the value of GMT Sheet's tensile strength in the direction of fiber orientation 90 is similar with the value of pp's intensity when fiber orientation function is J= 0.7, regardless of the fiber content. Tensile strength of GMT Sheet is affected by the fiber orientation distribution more than by the fiber content.

• 가정과삶의질연구
• /
• 제20권6호
• /
• pp.69-79
• /
• 2002

The deteriorated apartments make a social problem in now a days. After all, a new alternative plan for deteriorated apartments such as the remodelling concept must be considered. This study aims to survey the perception levels among residents in deteriorated apartments relating to remodelling. It might be provide the basic data which could be used for the analysis of consumers in the future implementation of deteriorated remodelling projects. The analytical methods adopted in this study were factor analysis, 1-test, one-way ANOVA, post-hoc estimation(Scheffe test) by the SPSS 10.1 for Windows program. Through the factor analysis for the perception types regarding remodelling, the factors were named ‘function improvement orientation’ , ‘property value orientation’, ‘individual-household improvement orientation’, and ‘negative attitude to remodelling’. The analysis of the perception types regarding remodelling, by the family characteristics, socio-economic characteristics, residence characteristics, apartment block variables, resident's value orientation, and resident's satisfaction level, indicated that the perception degree of the ‘property value orientation’was the highest, followed by the ‘function improvement orientation’.