• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.581-593
• /
• 2022

As energy depletion and environmental pollution problems are intensified, research has been conducted actively on alternative energy sources, an eco-friendly and continuous available energy conversion system. So has been organic solar cells whose efficiency is improved to 18.32%. The photoactive layer inside the solar cell is composed of a donor and a acceptor, and the combination of materials capable of effectively exchanging electrons greatly affects the efficiency of the organic solar cell. Accordingly, various researches have been conducted to improve the efficiency, and the maximum efficiency could be achieved by a solar cell with high carrier generation and low charge recombination characteristics through the introduction of a non-fullerene acceptor and material reconstruction. Organic solar cells are still difficult to commercialize due to their efficiency limitations and light stability, but if a photoactive layer consisting of a donor capable of efficiently absorbing long-wavelength light and an acceptor capable of forming an appropriate energy level is designed, the efficiency of the organic solar cell will reach 20%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.792-796
• /
• 2002

In this work, porous silicon(PS) layer is used as a sensing material to detect organic gases. To do this, PS sensors with membrane structure are fabricated. The sensors were made by applying the technologies of membrane formation by anisotropic etching of silicon, and PS layer formation by anodization in HF solution. From fabricated sensors, current-voltage (I-V) curves were measured against ethanol (called alcohol), methanol and acetone gases evaporated from 0.1 to 0.5% solution concentrations at $36^{\circ}C$. As the result, all curves showed rectifying behavior due to a diode structure between Si and PS, and the conductance of sensor devices increased largely with the organic solution concentration at high voltage of 5V.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.3
• /
• pp.142-148
• /
• 2002

Considerable progress has been made in organic photorefractive materials, since the first observation of photorefractive phenomena from organic materials. Within recent years, a large number of organic photorefractive materials, especially amorphous materials, have been developed based on polymeric composites, fully functional polymers and the multi-functional chromophore approach. Among these organic photorefractive materials, some of them containing carbazole components as a charge transporting function have been demonstrated to exhibit high performance photorefractive effects. The carbazole building blocks with charge transporting function or multifunctions play a very important role in photorefraction. In this paper, it confirmed that acceptor-substituted carbazoles show the multifunctionality both of photoconductivity and electro-optic(EO) activity and photorefractive materials newly can be developed with acceptor-substituted carbazoles.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.214-217
• /
• 2002

The internal quantum efficiency of organic light emitting devices(OLEDs) using fluorescent organic materials is limited within 25% because of the triplet excitons which can hardly emit light. So there has been considerable interest in finding ways to obtain light emission from triplet excitons. One approach has been to add phosphorescent compounds to one of the layers in OLEDs. Then triplet excitons can transfer to these phosphorescent molecules and emit light. In this study, multilayer OLEDs with phosphorescent emitter, Iridium complexes were prepared. The devices with a structure of ITO/TPD/Ir complex doped in the host material/Alq3/Li:Al/Al were fabricated, and its electrical and optical characteristics were studied. Using various Ir complexes and the host materials, we fabricated several devices and investigated the device characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.177-180
• /
• 2002

The purpose of this thesis is to develope buffer materials by the plasma polymerization method. In this article the buffer materials, plasma poly thiophene(PPTh) is used to study the interface of eter/organic in organic light emitting diodes(OLED). The interface of meter/organic materials is the important and critical objectives in development of OLED. The hole transport layer was N,N'-dipheneyl-N, N'bis-(3-methypheneyl)-1,1'dipheneyl-4,4'-diamine (TPD); the host material of mission layer was 8-tris-hydroxyquinoline aluminium (Alq3). When PPTh was inserted between ITO and TPD, emission efficiency increased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.1038-1042
• /
• 2005

We have investigated dielectric properties depending on bias voltage in organic light-emitting diodes using 8-hydroxyquinoline aluminum $(Alq_3)$ as an electron transport and emissive material. We analyzed the dielectric properties of organic light-emitting diodes using impedance of characteristics. Impedance characteristics was measured complex impedance Z and phase $\theta$ in the frequency range of 40 Hz to $10^8$ Hz. We obtained complex electrical conductivity, dielectric constant, and loss tangent $(tan\delta)$ of the device at room temperature. From these analyses, we are able to interpret a conduction mechanism and dielectric properties contributed by an interfacial and orientational polarization.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.897-902
• /
• 1998

We prepared Organic LED with a two layer structure by vacuum evaporation. The diode consisted of hole transfer layer (thickness of 30, 50, 70 nm) and electron transfer layer (thickness of 70, 50, 30 nm) material, which was N, N'-diphenyl- N, N'-bis-(3-methyl phenyl)-1,1'-diphenyl-4,4'-diamine)(TPD) and tris(8-hydroxy quinoline) aluminum(Alq3), respectively. We investigated EL properties of the LED with various thickness and cathode electrode. The best results were obtained when thickness of the electron layer is equal to that of emission layer and when AlLi alloy was used as a cathode. The EL intensity, luminance and efficiency of organic LED with equal of layer thick were improved seven, three and two times, respectively. Alq3 was ionized by carrier injection from cathode and could produce exitons. After electron-hole pairs were formed by combination of the electrons and holes at the emission layer, Alq3 layer emitted light.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.1
• /
• pp.35-40
• /
• 2008

In OLED vacuum evaporation process, the essential requirements include good uniformity of the film thickness over a glass substrate. And, it is commercially significant to improve the consuming efficiency of material of the evaporant which is deposited on the substrate because of high price of organic materials. In this paper, to achieve the better thickness uniformity and the better organic material consuming rate, a process optimization algorithm was developed by understanding vacuum evaporation process parameters that affect the material consuming efficiency and the uniformity of film thickness. Based on the method developed in this study, the vacuum evaporation process of OLED was successfully controlled. The developed method allowed the manufacture of high quality OLED displays with cheaper fabrication cost.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.4
• /
• pp.99-107
• /
• 2003

Normally coating is used a method for protecting reinforced concrete. For this purpose, organic as well as inorganic coatings are used. The advantages of inorganic coatings are lower absorption of UV, non-burning etc. On the other hand, organic coatings have the advantage of low permeability of $CO_2$, $SO_2$ and water. Organic coatings provide better protection for reinforced concrete. However, in organic coatings such as epoxy, urethane and acryl, long-term adhesive strength is reduced and the formed membrane of those is blistered by various causes. Also when organic coatings are applied to the wet surface of concrete, they have a problem with adhesion. So, we developed coating material, WGS-Eco which was hybridized with polymer and cement based material to protect concrete structures and solve problems of organic coatings. This study was conducted an comparative evaluation on physical and durable performance of developed coating material and previously used coating materials. As a result, the performance of developed coating material was not inferior to organic coating materials. So, the developed coating material was considered as a suitable coating material which had advantages of inorganic and organic coatings for protecting concrete.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.497-499
• /
• 2005

A portable terminal assistant market grows rapidly every year and it requires many change in research on display devices. Among many newly developing methods, OLED(Organic Light Emitting Diode) is considered an advanced flat display device because its excellent characteristics, including high speed response, full color performance, low power consumption and flux of panel. However changes in the market of display shows that the market will require 3-dimensional images, but it is hard for existing 2-dimensional displays to make 3-dimensional images. Therefore we will try to find various methods such as holograms. In this paper, we will show existing flat displays can make 3-dimensional images by applying Lenticular Screen printing techniques on the organic semiconductor display device.