• 제목/요약/키워드: Organic Coatings

검색결과 147건 처리시간 0.028초

B2O3-Bi2O3-ZnO계 유리를 이용한 백색 LED용 색변환 렌즈의 광 특성 (Optical Properties of Color Conversion Lens for White LED Using B2O3-Bi2O3-ZnO Glass)

  • 채유진;이미재;김진호;황종희;임태영;정희석;이영식;김득중
    • 한국전기전자재료학회논문지
    • /
    • 제26권8호
    • /
    • pp.614-619
    • /
    • 2013
  • Recently, remote phosphor is reported for white LED enhancing of phosphor efficiency compared with conventional phosphor-based W-LED. In this study, Remote phosphor was produced by screen printing coating on glass substrate with phosphor contents rated paste and heat treatment. The paste consists of phosphor, lowest softening glass frit and organic binders. Remote phosphor can be well controlled by varying the phosphor content rated paste. After mounting remote phosphor on top of blue LED chip, CCT, CRI, and luminance efficiency were measured. The measurement results showed that CCT, CRI, and luminance efficiency were 6,645, 68, and 1,16l m/W in phosphor 80 wt.% remote phosphor sintered at $600^{\circ}C$.

반응성 스프레이방법으로 제작한 티타늄 알루미나이드/탄화물 복합박막의 미세조직과 경도 (Microstructure and Hardness of Titanium Aluminide/Carbide Composite Coatings Prepared by Reactive Spray Method)

  • 한창석;진성윤
    • 한국재료학회지
    • /
    • 제30권7호
    • /
    • pp.350-358
    • /
    • 2020
  • A variety of composite powders having different aluminum and carbon contents are prepared using various organic solvents having different amounts of carbon atoms in unit volume as ball milling agents for titanium and aluminum ball milling. The effects of substrate temperature and post-heat treatment on the texture and hardness of the coating are investigated by spraying with this reduced pressure plasma spray. The aluminum part of the composite powder evaporates during spraying, so that the film aluminum content is 30.9 mass%~37.4 mass% and the carbon content is 0.64 mass%~1.69 mass%. The main constituent phase of the coating formed on the water-cooled substrate is a non-planar α2 phase, obtained by supersaturated carbon regardless of the alloy composition. When these films are heat-treated at 1123 K, the main constituent phase becomes γ phase, and fine Ti2AlC precipitates to increase the film hardness. However, when heat treatment is performed at a higher temperature, the hardness is lowered. The main constitutional phase of the coating formed on the preheated substrate is an equilibrium gamma phase, and fine Ti2AlC precipitates. The hardness of this coating is much higher than the hardness of the coating in the sprayed state formed on the water-cooled substrate. When hot pressing is applied to the coating, the porosity decreases but hardness also decreases because Ti2AlC grows. The amount of Ti2AlC in the hot-pressed film is 4.9 vol% to 15.3 vol%, depending on the carbon content of the film.

고종횡비를 갖는 용액기반 원통형 마이크로렌즈 제조 (Fabrication of Solution-Based Cylindrical Microlens with High Aspect Ratio)

  • 전경준;이진영;박종운
    • 반도체디스플레이기술학회지
    • /
    • 제20권1호
    • /
    • pp.70-76
    • /
    • 2021
  • A cylindrical microlens (CML) has been widely used as an optical element for organic light-emitting diodes (OLEDs), light diffusers, image sensors, 3D imaging, etc. To fabricate high-performance optoelectronic devices, the CML with high aspect ratio is demanded. In this work, we report on facile solution-based processes (i.e., slot-die and needle coatings) to fabricate the CML using poly(methyl methacrylate) (PMMA). It is found that compared with needle coating, slot-die coating provides the CML with lower aspect ratio due to the wide spread of solution along the hydrophilic head lip. Although needle coating provides the CML with high aspect ratio, it requires a high precision needle array module. To demonstrate that the aspect ratio of CML can be enhanced using slot-die coating, we have varied the molecular weight of PMMA. We can achieve the CML with higher aspect ratio using PMMA with lower molecular weight at a fixed viscosity because of the higher concentration of PMMA solute in the solution. We have also shown that the aspect ratio of CML can be further boosted by coating it repeatedly. With this scheme, we have fabricated the CML with the width of 252 ㎛ and the thickness of 5.95 ㎛ (aspect ratio=0.024). To visualize its light diffusion property, we have irradiated a laser beam to the CML and observed that the laser beam spreads widely in the vertical direction of the CML.

Corrosion visualization under organic coating using laser ultrasonic propagation imaging

  • Shi, Anseob;Park, Jinhwan;Lee, Heesoo;Choi, Yunshil;Lee, Jung-Ryul
    • Smart Structures and Systems
    • /
    • 제29권2호
    • /
    • pp.301-309
    • /
    • 2022
  • Protective coatings are most widely used anticorrosive structures for steel structures. The corrosion under the coating damages the host material, but this damage is completely hidden. Therefore, a field-applicable under-coating-corrosion visualization method has been desired for a long time. Laser ultrasonic technology has been studied in various fields as an in situ nondestructive inspection method. In this study, a comparative analysis was carried out between a guided-wave ultrasonic propagation imager (UPI) and pulse-echo UPI, which have the potential to be used in the field of under-coating-corrosion management. Both guided-wave UPI and pulse-echo UPI were able to successfully visualize the corrosion. Regarding the field application, the guided-wave UPI performing Q-switch laser scanning and piezoelectric sensing by magnetic attachment exhibited advantages owing to the larger distance and incident angle in the laser measurement than those of the pulse-echo UPI. Regarding the corrosion visualization methods, the combination of adjacent wave subtraction and variable time window amplitude mapping (VTWAM) provided acceptable results for the guided-wave UPI, while VTWAM was sufficient for the pule-echo UPI. In addition, the capability of multiple sensing in a single channel of the guided-wave UPI could improve the field applicability as well as the relatively smaller size of the system. Thus, we propose a guided-wave UPI as a tool for under-coating-corrosion management.

LC50 Determination of tert-Butyl Acetate using a Nose Only Inhalation Exposure in Rats

  • Yang, Young-Su;Lee, Jin-Soo;Kwon, Soon-Jin;Seo, Heung-Sik;Choi, Seong-Jin;Yu, Hee-Jin;Song, Jeong-Ah;Lee, Kyu-Hong;Lee, Byoung-Seok;Heo, Jeong-Doo;Cho, Kyu-Hyuk;Song, Chang-Woo
    • Toxicological Research
    • /
    • 제26권4호
    • /
    • pp.293-300
    • /
    • 2010
  • tert-Butyl acetate (TBAc) is an organic solvent, which is commonly used in architectural coatings and industrial solvents. It has recently been exempted from the definition of a volatile organic compound (VOC) by the Air Resources Board (ARB). Since the use of TBAc as a substitute for other VOCs has increased, thus its potential risk in humans has also increased. However, its inhalation toxicity data in the literature are very limited. Hence, inhalation exposure to TBAc was carried out to investigate its toxic effects in this study. Adult male rats were exposed to TBAc for 4 h for 1 day by using a nose-only inhalation exposure chamber (low dose, $2370\;mg/m^3$ (500 ppm); high dose, $9482\;mg/m^3$ (2000 ppm)). Shamtreated control rats were exposed to clean air in the inhalation chamber for the same period. The animals were killed at 2, 7, and 15 days after exposure. At each time point, body weight measurement, bronchoalveolar lavage fluid (BALF) analysis, histopathological examination, and biochemical assay were performed. No treatment-related abnormal effects were observed in any group according to time course. Based on those findings, the median lethal concentration ($LC_{50}$) of TBAc was over $9482\;mg/m^3$ in this study. According to the MSDS, the 4 h $LC_{50}$ for TBAc for rats is over $2230\;mg/m^3$. We suggested that this value is changed and these findings may be applied in the risk assessment of TBAc which could be beneficial in a sub-acute study.

Ormocer 계열 수복재의 물성에 관한 연구 (SELECTED MECHANICAL PROPERTIES OF ORMOCER RESTORATIVE MATERIALS)

  • 이동수;정태성;김신
    • 대한소아치과학회지
    • /
    • 제29권3호
    • /
    • pp.362-370
    • /
    • 2002
  • 최근 20년간 다양한 종류의 심미 수복재가 개발되었고, 특히 지난 5년 동안에는 그 수에 있어서 극적인 증가추세를 보였다. 최근 들어, ormocer라는 새로운 종류의 광중합형 수복재료가 소개되었는데, 화학 분야에서는 이미 오래 전부터 알려져 있던 성분으로, 광학렌즈 등의 표면경화제로 이용되어 오다가 최근 치과용 수복재에 도입되었다. 'Ormocer' 란 'Organically Modified Ceramics'의 약자로 'Ormosils' (Organically Modified Silicates)로도 알려져 있다. 그러나, 이 새로운 수복재에 대한 연구는 아직 미흡한 실정이다. 본 연구에서는 서로 다른 계통의 광중합형 수복재들(Z-100, Surefil, Tetric Ceram, Dyract AP)과 ormocer(Admira)를 압축강도와 굴곡강도 측면에서 비교 평가하고, 구강내 환경과 유사한 조건에서 수분흡수가 그 물성에 미치는 영향을 평가할 목적으로 시도되어 다음과 같은 결과를 얻었다. 1. 1일 후에 측정한 Admira의 압축강도는 Surefil보다는 낮았으나, 다른 재료들과는 유의한 차이를 나타내지 않았다(p>0.05). 2. 1일 후에 측정한 Admira의 굴곡강도는 다른 4종의 재료에 비해서 낮았다(p<0.05). 2일부터는 3종의 복합레진에 비해서 낮았다(p<0.05). 3. 실험기간(30일) 중 hybrid composite resin군(Z-100, Tetric Ceram)과 packable resin(Surefil)군 간에는 압축강도와 굴곡강도에서 유의한 차이가 없었다(p>0.05). 4. 실험에 사용된 5종의 수복재 모두 압축강도와 굴곡강도가 2일까지 증가하다가 7일부터 감소하였다(p<0.05). 5. 각 재료의 시간에 따른 압축강도와 굴곡강도의 변화양상은 통계적으로 유사하였다(p>0.05).

  • PDF

유-무기 하이브리드 화합물과 Particle-Binder 공정을 이용한 소수성 코팅막 제조 (Preparation of Hydrophobic Coating Layers Using Organic-Inorganic Hybrid Compounds Through Particle-to-Binder Process)

  • 황승희;김효원;김주영
    • 접착 및 계면
    • /
    • 제21권4호
    • /
    • pp.143-155
    • /
    • 2020
  • Sol-Gel 공정을 통해서 제조되는 유-무기 하이브리드 화합물들은 방청 코팅, 방빙 코팅(Anticing), 자가 세정 코팅, 반사 방지 코팅 등과 같은 기능성 코팅 재료로 널리 사용되어져 왔다. 특히 소수성 코팅 표면을 제조하기 위해서는 코팅표면의 표면에너지가 낮고 코팅 표면의 조도를 제어가 요구된다. 표면에너지와 표면 조도를 조절하는 전형적인 공정은 in-situ fabrication 공정, 'Pre-fluorinating/Post-roughening', 'Pre-roughening/ Post-fluorinating이다. 본 연구에서는 in-situ fabrication 공정인 Particle-Binder 공정을 이용해서 소수성 코팅표면을 제조하였다. 3관능기 유기실란화합물과 불소 함유 유기실란 화합물과의 가수분해 및 축합반응을 통해 제조된 불소함유 유-무기 하이브리드를 바인더로 사용하여서 무기물 나노입자와 혼합하여 소수성 코팅액을 제조하고 유리 기재 위에 스핀코팅 후 열건조하여서 코팅막을 제조하였다. 바인더인 유-무기 하이브리드 화합물의 불소 함유 실란화합물의 첨가량, 첨가순서, 무기물 나노입자 첨가량에 따른 코팅막의 물성 변화를 조사하였다. 분석결과 불소 함량이 10 wt%인 유-무기 하이브리드 화합물(GPTi-HF10)을 바인더로 사용하여서 제조된 코팅막이 가장 소수성이 우수하였으며 수접촉각은 (107.52 ± 1.6°), 이 바인더와 무기물 나노입자의 무게비가 1:3인 경우(GPTi-HF10-MS 3.0)에 가장 높은 수접촉각(130.84±1.99°)을 나타내었다.

접착제에서 발생하는 휘발성유기화합물(VOCs)에 대한 안정성 연구 (The Studies of Stability for Volatile Organic Compounds(VOCs) Generated from the Adhesives)

  • 이현경;위광철
    • 보존과학회지
    • /
    • 제31권3호
    • /
    • pp.243-254
    • /
    • 2015
  • 본 연구에서는 각종 재료에 의한 잠재적인 손상 검증 실험인 Oddy Test를 통해 금속유물 보존처리 과정에서 사용되는 접착제 및 코팅제를 선정하여 부식반응이 관찰된 시편으로 손상 원인을 확인하고자 한다. 6종의 접착제와 Fe, Pb, Cu, Ag 4종의 금속 시편을 사용하였다. 연구 결과, 중량 변화는 Cellulose계 접착제에 노출된 Fe시편이 29.87%로 높은 증가를 보였으며, Pb, Cu, Ag시편 순으로 증가율을 보였다. 색도 측정 결과는 Cellulose계 접착제의 변화값이 높게 나타났다. 접착제에서 발생하는 VOCs를 GC-MS로 분석한 결과, 접착제 6종 모두 Acetic acid가 검출되었다. 그 중 Cellulose계 접착제에서 다른 5종의 접착제와 비교하였을 때 1mg당 VOCs농도가 900배 이상 함량이 높았고, 소량의 Formic acid가 검출되었다. 이는 산성 불순물과 빛에 의해 촉진되기 때문으로 추측된다. 이 반응이 분자량 감소와 질소산화물과 다량의 산을 생성하는 결과가 되며 황변화 등 부식 촉진의 요인이 된다고 판단된다.

랫드에서 초산 제3부틸의 최기형성 시험 (Teratogenicity Study of tert-Butyl Acetate in Rats)

  • 안태환;양영수;이종찬;강성수;배춘식;김성호;김종춘;김현영;정용현
    • Toxicological Research
    • /
    • 제23권2호
    • /
    • pp.151-158
    • /
    • 2007
  • tert-Butyl acetate is an organic solvent used for coatings, industrial cleaning, and surface treatment applications. This study investigated the potential adverse effects of tert-butyl acetate on pregnant dams and embryo-fetal development after maternal exposure on gestational days 6 through 19 in rats. The test chemical was administered to pregnant rats by gavage at dose levels of 0, 500, 1,000, 1,500, and 2,000 mg/kg/day. All dams were subjected to a caesarean section on day 20 of gestation and their fetuses were examined for any external, visceral, and skeletal abnormalities. At 2,000 mg/kg, treatment-related clinical signs, including piloerection, abnormal gait, decreased locomotor activity, loss of fur, reddish tear, anorexia, nasal discharge, vocalization and coma, were observed in a dose-dependent manner. All dams died between the 2nd day and 5th day of treatment due to a severe systemic toxicity. At 1,500 mg/kg, minimal maternal toxicity including an increase in the incidence of decreased locomotor activity and loss of fur, and an increase in the weights of adrenal glands and liver was observed. On the contrary, no significant adverse effect on the embryo-fetal development was detected. There were no adverse effects on either pregnant dams or embryo-fetal development at <1,000 mg/kg. These results show that a 14-day repeated oral dose of tert-butyl acetate in rats caused a minimal maternal toxicity including increases in the incidence of clinical signs and the weights of adrenal glands and liver, but no embryotoxicity and teratogenicity at 1,500 mg/kg/day. Under these experimental conditions, the no-observed-adverse-effect level (NOAEL) of tert-butyl acetate is estimated to be 1,000 mg/kg per day for dams and 1,500 mg/kg per day for embryo-fetal development.

Taguchi법을 이용한 Ti/TiO2/IrO2-RuO2전극의 부식특성 최적화 (Optimization of Corrosion Properties of Ti/TiO2/IrO2-RuO2 Electrodes via Taguchi Method)

  • 이득용;채경선;최형기;예경환;안중홍;송요승
    • 한국세라믹학회지
    • /
    • 제39권6호
    • /
    • pp.582-588
    • /
    • 2002
  • Ti 기판에 TiO$_2$ 중간층을 플라즈마 용사법으로 증착 후 IrO$_2$-RuO$_2$ 박막을 졸-겔과 dip coating법으로 제조하였다. 코팅 층의 접착력을 향상시키기 위하여 유기화합물과 glass brit을 첨가하였다. Taguchi법의 망대특성과 Lls(2$^1$$\times$3$^{7}$ )의 직교배열표를 이용하여 IrO$_2$-RuO$_2$ 박막의 최적조건인 인자와 수준 조합의 최적화를 전류밀도를 측정 분산분석하였다. 최적의 코팅조건은 각각 ethyl cellulose의 점도는 100cp, 건조온도 및 시간은 17$0^{\circ}C$ 20분, 열처리온도 및 시간은 75$0^{\circ}C$ 10분, 전도성 분말과 glass frit의 무게비는 99:5, 최종열처리시간은 120분, 주입산소량은 5sccm이었다. 분산분석결과, 유의수준이 $\alpha$=0.1인 통계적으로 90%신뢰공정이었다.