• 한국항공우주학회지
• /
• 제31권7호
• /
• pp.63-68
• /
• 2003

쇼트피닝 가공은 금속부품의 피로특성 향상을 위해 대부분 널리 이용되고 있는 방법이다. 쇼트피닝 가공에 있어 재현성이 있고 신뢰할 수 있는 최적화된 피로특성 증가를 위해 가장 중요한 점이 쇼트피닝 변수 조절이다. 본 논문에서는 최적 피닝강도(알멘강도) 조건에 대한 실험적인 연구가 수행되었다. 피로 특성에 관한 최적피닝의 효과를 검토하기 위하여 회전굽힘피로시험법을 채택하였다. 실험 결과 피로강도와 피로수명이 최적피닝 조건에 의해 크게 증가하였으나 언더피닝 및 오버피닝의 경우에는 감소함을 보였다.

• 한국작물학회지
• /
• 제54권4호
• /
• pp.416-421
• /
• 2009

This experiment was conducted to find out optimum priming treatment conditions to the sesame seed as a preliminary study for enhancing sesame germination properties. Effective priming agents and concentrations for sesame seed were $K_3PO_4$, 200 mM and PEG6000, -1.0 MPa respectively. Optimum priming temperature and duration were $15^{\circ}C$, 4 days in view of germination speed and germination percentage. PEG6000 with -1.0 MPa was selected as an efficient priming treatment condition at $15^{\circ}C$, 4 days. This study suggested that priming treatment to sesame seed would be an effective technique enhancing sesame seed germination and shortening time to the $T_{50}$ at the field condition, but the efficiency of priming treatments to the sesame seed would be strongly dependent on individual or integrated conditions of priming agent, concentration, temperature and duration etc.

• Elastomers and Composites
• /
• 제50권1호
• /
• pp.30-34
• /
• 2015

Thermo-mechanical treatment process of a compressed open-cell rigid polyurethane foam (OC-RPUF), which was fabricated for the vacuum insulation panel (VIP), was studied to obtain an optimum condition for the dimensional stability by the relaxation of compressive stress. Thermo-mechanical deformation of the sample OC-RPUF was shown to occur from about $120^{\circ}C$. Yield stress of 0.36 MPa was shown at about 10% yield strain. And, densification of the foam started to occur from 75% compressive strain and could be continued up to max. 90%. Compression set of the sample restored after initial compression to 90% at room temperature was ca. 82%. Though the expansion occurred to about twice of the originally compressed thickness in case of temperature rise to $130^{\circ}C$, it could be overcome and the dimensional stability could be maintained if the constant load of 0.3 MPa was applied. As the result, a thermo-mechanical treatment process, i.e, annealing process at temperature of $130{\sim}140^{\circ}C$ for about 20 min as is the maximum compressed state at room temperature, should be required for dimensional stability as an optimum condition for the use of VIP core material.

• Journal of the Korean Wood Science and Technology
• /
• 제28권3호
• /
• pp.9-13
• /
• 2000

본 연구는 해마다 100만 톤 이상이 생산되는 국내산 왕겨를 이용하여 왕겨보드를 제조함에 있어, 무처리 왕겨로 제조한 왕겨보드의 기계적 성질의 단점을 보완하기 위하여 왕겨를 전처리함으로써 그 물리 기계적 성질을 개선하기 위해 실시되었다. 연구결과를 요약하면, 무처리, 증자처리 및 가성소다로 알칼리처리한 왕겨보드보다 폭쇄처리한 왕겨보드가 휨강도 및 박리강도가 더 높았으며, 이때 적정 폭쇄처리 조건은 압력 20kgf/$cm^2$, 시간 1분과 압력 25kgf/$cm^2$, 1분이었다. 무처리 왕겨보드의 경우 휨강도, 박리강도 모두 KS를 만족시키지 못한 반면, 폭쇄처리 왕겨 보드의 경우 KS PB 18.0형의 기준을 모두 만족시켰으며, PB 대조구와 비교할 때 동등한 강도를 보였다. 기타 왕겨 전처리의 경우에 있어서도 가성소다처리보다는 증자처리가 왕겨보드의 강도를 향상시키는 것으로 나타났다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.803-808
• /
• 2000

This thesis studied whether friction welding of SPSS, localized torsion bar material could be accomplished or not. And then optimum welding conditions were examined and leaded through tensile, impact, torsion and hardness test after postweld heat treatment of the actual field condition. Obtained results were as follows; Linear relationship was existed between heating time and total upset, and a quadratic equation model could be made between tensile strength and heating time. Optimum welding conditions with fine structure were as follows in case total upset(U)=8.5mm; the number of rotations(n)=2,000 rpm, heating pressure($p_1$)=80MPa, upset pressure($p_2$)=200MPa, heating time($t_1$)=4sec, upset time($t_2$)=3 sec.

• 한국약용작물학회지
• /
• 제18권1호
• /
• pp.9-14
• /
• 2010

Several presowing seed treatments have been used to facilitate the seed germination and seedling emergence. The study was performed to design a model of presowing seed treatments in Taraxacum platycarpum. Germination and seedling growth responses to temperature, drying, chilling, $GA_3$ and priming were investigated to know the optimum germination conditions and presowing treatment. The optimum temperature condition for germination and seedling growth were $15{\sim}20^{\circ}C$ at dark condition. The seeds exposed to infra red light, however, did not germinate. The moisture content of seeds dried at $35^{\circ}C$ for 3.5 hours was returned to the level of unimbibed seeds. The germination of seeds dried under dark condition was better than those dried under infra red light. Prechilling treatment imposed for 6 weeks showed higher germination rate than $GA_3$ treatment or priming. In field test, the highest field emergence was observed in the seeds dried after prechilled for 6 weeks and followed by drying followed by $GA_3$ > low temperature > $KNO_3$ priming. Imbibition with 0.1 mM $GA_3$ solution for 2 hours then drying at 35 for 3.5 hour under dark condition was effective to the practical presowing treatment for Taraxacum seeds.

• 기술사
• /
• 제31권5호
• /
• pp.110-120
• /
• 1998

The effect of heat treatment and the order of antioxidants treatment toward the thermally oxidized palm oil which has been stored at 60 $^{\circ}C$ was studied. The summerized results of this study are as follows; 1. In the accelerated autoxidation condition, tocopherol showed no distinct effect on the changes of peroxide of value between added tocopherol samples pre-and post treatment by heating. But, rosemary extract showed opposite result. It was supposed that rosemary extract had lower thermostability then tocopherol, because rosemary extract lost it's antioxidative activity during heating process. 2. The changes of acid value and anisidine value were more affected by heat treatment than the order of antioxidant treatment. 3. The oxidative stability measured by OSI showed same tendency as peroxide value. That is, the antioxidative activity of tocopherol in palm oil was more dependent on addition of antioxidants than heat treatment, but the rosemary extract had opposite character for antioxidative action in palm oil.

• 한국표면공학회지
• /
• 제16권3호
• /
• pp.98-107
• /
• 1983

A study on the improvement of wear resistance of brasses by electroplating and diffusion treatment of tin was carried out. The optimum condition of the treatment obtained was as follows. Plating thickness of tin : 5 - 9 $\mu\textrm{m}$ Condition of diffusion treatment : atmosphere ; fused nitrate bath (KNO3 + NaNO3) temperature and time ; 1st step 320$^{\circ}C$, 60min. and 450$^{\circ}C$, 30min. During the diffusion treatment, internetallic compounds of Cu-Sn were formed and these compounds were identified as η, $\varepsilon$ and $\delta$ phase from the outer tin layer. It was considered that the improvement of wear resistance of brasses by the treatment is because of the formation of intemetallic compounds particalarly $\varepsilon$phase which is very hard, between soft tin layer brass.

• 열처리공학회지
• /
• 제11권2호
• /
• pp.121-130
• /
• 1998

The effects of alloying elements(Mo, Cu, Ni) and austempering temperature conditions on the microstructural morphologies and mechanical properties in austempered ductile cast iron has been investigated. The austempering at $350^{\circ}C$ for 2hrs after austenitizing at $900^{\circ}C$ for 2hrs in all specimens with various alloying elements was optimum because the good combination of tensile and yield strength, hardness and impact value was obtained. The microstructures of these ADIs treated by a forementioned austempering condition are nearly a mixture type of needle and feathery bainite. Among those alloys, Mo-Cu alloyed DCI had the best optimum mechanical properties of hardness and toughness for automobile parts by austempering treatment for 2hrs at $900^{\circ}C$ followed by $350^{\circ}C$ for 2hrs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1534-1536
• /
• 2007

ZnS-based orange-emitting phosphors were synthesized by two-step firing process: above $1000^{\circ}C$ to obtain hexagonal phase, and at $750^{\circ}C$ for cubic phase. The effect of heat treatment condition on the optical properties was investigated to fine an optimum condition for high-performance ZnS:Mn,Cu,Cl phosphor.