• Journal of the Korea Institute of Building Construction
• /
• v.21 no.1
• /
• pp.1-10
• /
• 2021

The purpose of this study is to evaluate the improvement of flow, compressive and flexural strengths of polymer cement mortar(PCM) using SBR latex mixed with blast-furnace slag and fly ash. The test specimens were prepared with SBR polymer dispersion, two types of admixture (blast-furnace slag and fly ash), five polymer-cement ratios (P/C; 0, 5, 10, 15 and 20%), and six admixture contents (0, 3, 5, 10, 15 and 20%), plain cement mortar was also made for comparison. From the test results, the flow of PCM was significantly improved compared to ordinary cement mortar, but the flow was slightly reduced when mixed with blast-furnace slag, and the flow was similar to PCM when mixed with fly ash. In addition, the compressive strength of PCM mixed with admixtures was significantly improved, but the flexural strength did not improve except for some mortars. It can be stated that the optimum mix proportions of PCM using SBR with admixture contents 10 to 15% and P/C 10% for the compressive strength improvement, and P/C 20% for flexural strength improvement are recommended respectively in this study.

• Clean Technology
• /
• v.20 no.3
• /
• pp.232-240
• /
• 2014

The significance of thermoplastic polyolefin polypropylene (PP) lies in its potential to replace polyvinyl chloride (PVC), the most widely used material for automobile interiors (door trim, dash board), which discharges harmful compounds in certain conditions. Another benefit of PP (0.855 amorphous - 0.946 crystalline $g/cm^3$) is its low density compared to that of PVC ($1.1-1.45g/cm^3$), which reduces vehicle weight. Market demand for eco-friendly water-based adhesive/coating material is rising significantly as a substitute for solvent-based adhesive/coating material which emits VOC and causes harmful working conditions. Under such context, in this study, a series of eco-friendly waterborne polyurethane-urea primer (a paint product that allows finishing paint to adhere much better than if it were used alone) for hydrophobic PP were prepared from different mix of DMPA content, NCO/OH molar ratio, various wt% of silicone diol and various soft segment content, among which DMPA of 21 mole %, NCO/OH molar ratio of 1.2, modified silicone diol of 5 wt% and soft segment content of 73 wt% led to good adhesion strength. Additionally, the incorporation of optimum content of additives (0.5 wt% dispersing agent, 0.5 wt% levelling agent, 1.5 wt% antifoaming agent, 3.0 wt% matting agent) into the optimum waterborne polyurethane-urea also enabled good stability, levelling, antifoaming and non-glossy.

• Horticultural Science & Technology
• /
• v.33 no.3
• /
• pp.303-308
• /
• 2015

The consumption of leaf vegetables has been steadily increasing in Korea. Leaf vegetables are used for "Ssam (vegetable wrap-up), eaf vegetables has been steadily increasing in Korea. Leaf vegetables are used for asoned condiments inside several layers of young vegetable leaves. This study investigated the effect of air temperature on the growth and phytochemical contents of beet (Beta vulgaris L.) and Ssamchoo (Brassica lee L. ssp. namai) grown in a closed-type plant factory system where fluorescent lamps were used as an artificial light source. Seeds of beet and Ssamchoo were sown in a peat-lite germination mix. The roots of 20-day-old seedlings were washed, and the seedlings were planted on a styrofoam board and grown in hydroponic beds for 25 days under fluorescent light. Plants were exposed to one of three different air temperature regimes (20, 25 and $30^{\circ}C$ during the day combined with $18^{\circ}C$ during the night), which were monitored with a sensor at 30 cm above the plant canopy. Increased plant height and leaf area were observed in beet at $25^{\circ}C$ and $30^{\circ}C$ compared to $20^{\circ}C$. For Ssamchoo, the greatest plant height, leaf area, fresh weight and dry weight were obtained at $20^{\circ}C$. Ascorbic acid content of beet and Ssamchoo leaves were highest at $30^{\circ}C$. In beet, total polyphenol and flavonoid contents were higher at $20^{\circ}C$ (42.4, $197.0mg{\cdot}g^{-1}DW$) and $25^{\circ}C$ (46.9, $217.0mg{\cdot}g^{-1}DW$) than $30^{\circ}C$ (22.4, $88.0mg{\cdot}g^{-1}DW$). In Ssamchoo, total polyphenol and flavonoid contents were also higher at $20^{\circ}C$ (79.2, $268.2mg{\cdot}g^{-1}DW$) and $25^{\circ}C$ (66.3, $258.3mg{\cdot}g^{-1}DW$), respectively, than $30^{\circ}C$ (53.7, $134.7mg{\cdot}g^{-1}DW$). Hence, the optimum temperature appears to be $20^{\circ}C$ for growing both beet and Ssamchoo in a closed-type plant factory system with fluorescent light.

• 한국유가공학회:학술대회논문집
• /
• 2002.04a
• /
• pp.59-60
• /
• 2002

Edible films such as wax coatings, sugar and chocolate covers, and sausage casings, have been used in food applications for years$^{(1)}$ However, interest in edible films and biodegradable polymers has been renewed due to concerns about the environment, a need to reduce the quantity of disposable packaging, and demand by the consumer for higher quality food products. Edible films can function as secondary packaging materials to enhance food quality and reduce the amount of traditional packaging needed. For example, edible films can serve to enhance food quality by acting as moisture and gas barriers, thus, providing protection to a food product after the primary packaging is opened. Edible films are not meant to replace synthetic packaging materials; instead, they provide the potential as food packagings where traditional synthetic or biodegradable plastics cannot function. For instance, edible films can be used as convenient soluble pouches containing single-servings for products such as instant noodles and soup/seasoning combination. In the food industry, they can be used as ingredient delivery systems for delivering pre-measured ingredients during processing. Edible films also can provide the food processors with a variety of new opportunities for product development and processing. Depends on materials of edible films, they also can be sources of nutritional supplements. Especially, whey proteins have excellent amino acid balance while some edible films resources lack adequate amount of certain amino acids, for example, soy protein is low in methionine and wheat flour is low in lysine$^{(2)}$. Whey proteins have a surplus of the essential amino acid lysine, threonine, methionine and isoleucine. Thus, the idea of using whey protein-based films to individually pack cereal products, which often deficient in these amino acids, become very attractive$^{(3)}$. Whey is a by-product of cheese manufacturing and much of annual production is not utilized$^{(4)}$. Development of edible films from whey protein is one of the ways to recover whey from dairy industry waste. Whey proteins as raw materials of film production can be obtained at inexpensive cost. I hypothesize that it is possible to make whey protein-based edible films with improved moisture barrier properties without significantly altering other properties by producing whey protein/lipid emulsion films and these films will be suitable far food applications. The fellowing are the specific otjectives of this research: 1. Develop whey protein/lipid emulsion edible films and determine their microstructures, barrier (moisture and oxygen) and mechanical (tensile strength and elongation) properties. 2. Study the nature of interactions involved in the formation and stability of the films. 3. Investigate thermal properties, heat sealability, and sealing properties of the films. 4. Demonstrate suitability of their application in foods as packaging materials. Methodologies were developed to produce edible films from whey protein isolate (WPI) and concentrate (WPC), and film-forming procedure was optimized. Lipids, butter fat (BF) and candelilla wax (CW), were added into film-forming solutions to produce whey protein/lipid emulsion edible films. Significant reduction in water vapor and oxygen permeabilities of the films could be achieved upon addition of BF and CW. Mechanical properties were also influenced by the lipid type. Microstructures of the films accounted for the differences in their barrier and mechanical properties. Studies with bond-dissociating agents indicated that disulfide and hydrogen bonds, cooperatively, were the primary forces involved in the formation and stability of whey protein/lipid emulsion films. Contribution of hydrophobic interactions was secondary. Thermal properties of the films were studied using differential scanning calorimetry, and the results were used to optimize heat-sealing conditions for the films. Electron spectroscopy for chemical analysis (ESCA) was used to study the nature of the interfacial interaction of sealed films. All films were heat sealable and showed good seal strengths while the plasticizer type influenced optimum heat-sealing temperatures of the films, 130$^{\circ}$C for sorbitol-plasticized WPI films and 110$^{\circ}$C for glycerol-plasticized WPI films. ESCA spectra showed that the main interactions responsible for the heat-sealed joint of whey protein-based edible films were hydrogen bonds and covalent bonds involving C-0-H and N-C components. Finally, solubility in water, moisture contents, moisture sorption isotherms and sensory attributes (using a trained sensory panel) of the films were determined. Solubility was influenced primarily by the plasticizer in the films, and the higher the plasticizer content, the greater was the solubility of the films in water. Moisture contents of the films showed a strong relationship with moisture sorption isotherm properties of the films. Lower moisture content of the films resulted in lower equilibrium moisture contents at all aw levels. Sensory evaluation of the films revealed that no distinctive odor existed in WPI films. All films tested showed slight sweetness and adhesiveness. Films with lipids were scored as being opaque while films without lipids were scored to be clear. Whey protein/lipid emulsion edible films may be suitable for packaging of powder mix and should be suitable for packaging of non-hygroscopic foods$^{(5,6,7,8,)}$.

• Korean journal of applied entomology
• /
• v.57 no.2
• /
• pp.57-64
• /
• 2018

The fungus gnat, Bradysia difformis, has been recognized as an important pest of greenhouse crops. There is a need for research on the control of the fungus gnat. However, it is difficult to obtain many generations of the fungus gnat for several kinds of research. Indoor propagation is a very useful method for obtaining enough individuals in cases where the need is for larvae in soil. This study was conducted to determine the optimum growing media and temperature conditions for rearing the fungus gnat in the laboratory. Under experimental temperature conditions, hatching, pupation, and eclosion rates were the highest at $20^{\circ}C$. The developmental period of the fungus gnat was shortened with higher temperatures. The greatest number of eggs was an average of 144 at $20^{\circ}C$. Using different types of larvae growth media, the highest hatching rates were 84.7 and 84.4% in water agar and potato disks, respectively. The larval period was the shortest, at 14.7 days, when grown on potato disks. The highest pupation and eclosion rates were 85.2 and 82.6% on potato disks, respectively. The highest number of eggs was an average of 125.6 on potato disks. Regarding the effects of different growth media on the eclosion rate of B. difformis, the highest eclosion rate was 88.4% on the soil mix, and was 50% on oatmeal, 25% on shredded potato. The results of four different inoculation levels of larvae on eclosion rate of B. difformis showed that the highest eclosion rate was 84.7% for 1,000 larvae. The eclosion rate was shortened with a higher number of larvae inoculated/cage. In the growth medium used, 3,000 eggs were better for the initial level of inoculation, showing a relatively high emergence rate and short developmental period. Mass rearing procedures were explained in detail.

• Korean journal of food and cookery science
• /
• v.17 no.4
• /
• pp.412-420
• /
• 2001

This study was conducted to identify the optimum cooking method and the ideal composition of Wax gourd Jung Kwa for the purpose of wide distribution. Wax gourd Jung Kwa was made by peeling off the wax gourd, digging out the stuff, slicing, soaking the pieces in ash water, and boiling slightly, then boiling down in honey, grain syrup. sugar, etc. As a result of sensory evaluation, the best color of Jung Kwa was observed in the recipe of pretreated wax gourd 300g, water 1 litre and grain syrup 495$m\ell$; for the flavor, hardness and chewiness, Pretreated wax gourd 300g, water 1 litre, corn syrup 475$m\ell$ and sugar 70g; for the adhesiveness, pretreated wax gourd 300g, water 1 litre and corn syrup 515$m\ell$; for the sweetness, pretreated wax gourd 300g, water 600$m\ell$ and sugar 90g and honey 120g. Overall Qualify was the highest in the recipe of pretreated wax gourd 300g, water 1 litre, com syrup 475$m\ell$ and sugar 70g, of which the sweetness was 74%. There were significant differences in all items (P＜0.05). For mechanical characteristics, the maximum cutting force was the highest in the samples with the recipe of pretreated wax gourd 300g, water 1 litre, corn syrup 475$m\ell$ and sugar 70g, and there were significant differences among all items (P<0.05). The highest moisture content, 45.54%, was observed in the recipe of pretreated wax gourd 300g. water 1 litre and corn syrup 475$m\ell$. There were significant differences among all items (P＜0.05). The L value(lightness) was the highest in the recipe of pretreated wax gourd 300g, water 1 litre, corn syrup 475 $m\ell$ and sugar 50g. The a value(redness) was the highest in the case of pretreated wax gourd 300g, water 1 litre, com syrup 475$m\ell$ and sugar 70g, which was almost red; and the b value(yellowness), wax gourd 300g, water 1 litre and corn syrup 475g, which gave almost Yellow color. Taking consideration of the above results, the most desirable recipe for wax gourd Jung Kwa was to mix the 300g of pretreated wax gourd with 20g of ash powder, boil them slightly for 2 min, soak them in cold water for 1 hour, and boil them down with 475$m\ell$ of com syrup, 70g of sugar, and 1 litre of water for 5 hours, resulting in the sweetness of 74%. The samples with above recipe were the best in flavor, chewiness and hardness in sensory evaluation, and showed the highest maximum cutting force and nearest red color in the mechanical test.