• 대한산업공학회지
• /
• 제26권3호
• /
• pp.200-205
• /
• 2000

An economic process monitoring procedure is presented using a surrogate variable for the case where performance variable is dichotomous. Every item is inspected with a surrogate variable and determined whether it should be accepted or rejected. When an item is rejected, the previous number of consecutively accepted items is compared with a predetermined number r to decide whether there is a shift in fraction nonconforming or not. The conditional distribution of the surrogate variable given the performance variable is assumed to be normal. A cost model is constructed which includes costs of inspection, misclassification, illegal signal, undetected out-of-control state, and correction. Methods of finding the optimum number r and screening limit are provided. Numerical studies on the effects of cost coefficients are also performed.

• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.62-67
• /
• 2010

Exhausting fossil fuel and increasing concern of air pollution have brought on the change of the focus of developing new vehicles from performance to fuel economy and emission. The gasoline engines adopting the naturally aspirated way use the throttle-body for engine load control. Therefore, its pumping loss increases more than that of the diesel engine, and also mostly operating in a partial load condition has bad influence on fuel economy and emission. In these days, the continuous variable valve timing system and variable induction system are adopted in order to improve fuel consumption and emission. In this study, we optimize the runner length and operate region of variable induction system to simulataneously improve the performance, fuel economy, and emission of gasoline engine with employing GT-Power as a CAE tool for engine analysis and PIAnO as PIDO tool for process integration and design optimization.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.786-790
• /
• 2002

In this study, structural optimum design was applied to the girder of magnet over head crane. The optimization was carried out using ANSYS Code for the deadweight of girder, especially focused on the thickness of its upper, lower, side and reinforced plates. The weight could be reduced up to around 15% with constraints of its deformation, stress, natural frequency and buckling strength. The structural safety was also verified by the buckling analysis of its panel structure. It might be thought to be very useful to design the conventional structures for the weight save through the structural optimization. The objective function and restricted function were estimated by the orthogonal array, and the sensitivity analysis of design variable fur that was operated.

• 전기학회논문지
• /
• 제65권12호
• /
• pp.2183-2188
• /
• 2016

This paper deals with the design process for an outer-rotor-type surface-mounted permanent magnet synchronous motor (SPMSM) used in continuous variable valve timing (CVVT) systems in automobiles with internal combustion engines. When the same size, outer-rotor-type SPMSMs generate larger torque and more stable than inner-rotor-type SPMSMs. For the initial design, space harmonic analysis (SHA) is used. In order to minimize the cogging torque, an optimization was conducted using Response Surface Methodology (RSM). At the end of the paper, Finite Element Analysis (FEA) is performed to verify the performance of the optimum model.

• 한국공간구조학회논문집
• /
• 제24권1호
• /
• pp.57-64
• /
• 2024

This study numerically compares optimum solutions generated by element- and node-wise topology optimization designs for free vibration structures, where element-and node-wise denote the use of element and nodal densities as design parameters, respectively. For static problems optimal solution comparisons of the two types for topology optimization designs have already been introduced by the author and many other researchers, and the static structural design is very common. In dynamic topology optimization problems the objective is in general related to maximum Eigenfrequency optimization subject to a given material limit since structures with a high fundamental frequency tend to be reasonable stiff for static loads. Numerical applications topologically maximizing the first natural Eigenfrequency verify the difference of solutions between element-and node-wise topology optimum designs.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.135-147
• /
• 2000

Section design of vehicle structure has been developed by two methods. One is the section property method which uses section property as a design variable. This method shows the tendency of an optimum section approximately. The other method is the section shape method which utilizes geometric parameter of section as a design variable. Practical solutions are obtained by this method. However, it is very expensive for large-scale problems due to the large number of geometric parameters. These two methods are compared through several sample problems. The finite element method is used for the structural and sensitivity analyses. The results are analyzed based on the number of function evaluations, the quality of cost function, the complexity of programing, and etc. The applications of both methods are also discussed.

• 한국강구조학회 논문집
• /
• 제24권6호
• /
• pp.671-682
• /
• 2012

박스형 거더나 박공형 철골조 프레임에서 주름웨브보의 사용은 최근 많이 늘어가고 있다. 그 이유는 얇은 주름웨브보를 사용함으로서 압연형강이나 용접을 이용한 조립보에 비해 중량을 크게 줄일 수 있으며, 박판의 좌굴은 주름이 막아줄 수 있기 때문이다. 자동생산기술의 향상으로 인해 주름웨브를 가진 단위 부재를 양산할 수 있게 되어 적용분야가 확장되고 있으며, 주름웨브보의 부재 제원을 고려한 최적설계의 구현이 필요하게 된다. 이를 위해 본 논문에서는 주름웨브보의 생산부재 데이터를 고려한 이산화 최적구조설계 프로그램을 개발하여 집중하중과 등분포하중을 받는 주름웨브 단순보에 대해 적용하였다. 최소중량을 목적함수로, 세장비, 응력 및 처짐을 제약조건으로 채택하고, 전역최소값을 탐색하기 위해서 유전자 알고리즘을 채택하였으며, 생산부재의 번호를 불연속설계변수로 이용하였다. 최종적으로 해석설계의 검증을 위해서 이산화 최적설계 결과를 연속일 때의 결과와 비교하였으며, 최적단면 특성에 대해 분석하였다.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.860-869
• /
• 2003

Design optimization of the heat sink with 7${\times}$7 square pin-fins is performed numerically using the Computational Fluid Dynamics (CFD) and the Computer Aided Optimization (CAO). In the pin-fins heat sink, the optimum design variables for fin height (h), fin width (w), and fan-to-heat sink distance (c) can be achieved when the thermal resistance ($\theta$$_{j}$) at the junction and the overall pressure drop ($\Delta$p) are minimized simultaneously. To complete the optimization, the finite volume method for calculating the objective functions, the BFGS method for solving the unconstrained non-linear optimization problem, and the weighting method for predicting the multi-objective problem are used. The results show that the optimum design variable for the weighting coefficient of 0.5 are as follows: w=4.653 mm, h=59.215 mm, and c=2.667 mm. In this case, the objective functions are predicted as 0.56K/W of thermal resistance and 6.91 Pa of pressure drop. The Pareto optimal solutions are also presented.re also presented.d.

• 대한토목학회논문집
• /
• 제5권4호
• /
• pp.9-14
• /
• 1985

본 연구에서는 평면 변형도상태 하에서 정수압을 받는 2차원 탄성 콘크리트 댐의 단면 모양을 최적화함으로써 댐의 질량을 최소화하였다. 최적화 문제의 목적함수로는 댐의 단면적이, 제약조건으로는 주응력 제약조건과 두께 제약조건들이, 설계변수로는 모델 경계의 모양이 채택되었다. 모델 영역의 변화에 따른 설계감도해석을 위해 최적화 문제를 범함수 형태로 변환한 후 연속체 역학의 물질미분 개념과 Adjoint Variable Technique 을 활용하였고, 최적화를 위해서는 Gradient Projection Method 를 사용하였다. 연구 결과 본 연구에 적용된 이론이 효율적이고 실제 탄성구조물 설계에 광범위하게 응용될 수 있음이 밝혀졌다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.209-214
• /
• 2003

This study presents the analysis of ball end milling machinability and its application to the determination of the optimum feedrate in the CNC machining process of sculptured surface. The methods which estimate the cutting force system is approached experimentally. The estimation strategy, named technological processor, was applied to the machining process of sculptured surface for finding optimum variable feedrate. From the result of practical implementation for the test model, it is ascertain that the technological processor have brought the dispersion of force profiles. As compared with conventional imposing of cutting conditions, the machining time has reduced by more than 60%.