• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.122-130
• /
• 1992

To improve the physical properties and the dyeing properties of silk, the silk fabric was treated with urea resin and reactive dyeing. The effects of urea resin concentration, pH of padding bath and curing condition were investigated in order to find optimum condition and the following results are obtained The optimum condition for the crease recovery of silk fabric was urea resin concentration of 80 g/ι, pH of 7, the curings temperature of about 135$^{\circ}C$, and the curing time of 3 minutes. The crease recovery and the thermal insulation ratio of silk fabric were increased by the above treatment. K/S increased as the adding amount of Na$_2$SO$_4$ increased, K/S, however was not affected by the adding amount of Na$_2$CO$_3$. Co1or fastness of the dyed fabrics treated with urea resin were improved slightly compared with untreated ones.

• Journal of the Korean Society of Tobacco Science
• /
• v.5 no.1
• /
• pp.25-33
• /
• 1983

This study was carried out to investigate the transplanting time, optimum fertilization and harvesting method, chemical contents and physical properties of burley tobacco in paddy field. The results obtained as follows. 1. It is recommendable to transplant after March. 29 to escape the frost injury. By reducing compound fertilizer and whole plant stalk curing, advanced the. last priming date by 5-8 days. 2. Total alkaloid, total nitrogen and phosphorus contents of cured leaf was comparable to those of upland-produce(1 tobacco, but potassium and chloride contents some what high. 3. Filling power and combustibility was also comparable to upland, and filling power was increased by reducing fertilizer and whole plant stalk curing. 4. In the 20o reducing fertilizer-5 Primings volt. the yield was some what decreased, but visual quality and value per 10a were high. 5. The total raw income of tobacco and rice cropping was increased 124~170% than that of rice cropping.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1465-1467
• /
• 2004

In this paper, deduced manufacturing condition of glass/glass curtain wall module and metal curtain wall module. From the results. lamination condition of glass/glass curtain wall module deduced optimum in pumping $time-120^{\circ}C$ 23min, slow $press-120^{\circ}C$. 300mmHg. 3min. standard $press-120^{\circ}C$. 200mmHg. 0.5min. fast $press-120^{\circ}C$. 100mmHg. 0.3min and $curing-140^{\circ}C$, 6min, and lamination condition of metal curtain wall module deduced optimum in pumping $time-120^{\circ}C$. 8min, slow $press-120^{\circ}C$, 700mmHg. 0.5min, standard $press-120^{\circ}C$, 600mmHg, 0.5min. fast $press-120^{\circ}C$, 100mmHg. 1.5min and $curing-140^{\circ}C$. 6min. This time. power uniformity of glass/glass curtain wall module and metal curtain wall module showed each ${\pm}2.7\%,\;{\pm}2.12\%$.

• 한국도로학회:학술대회논문집
• /
• 2011.03a
• /
• pp.175-181
• /
• 2011

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.160-160
• /
• 2016

In this study, we applied the low temperature curing Ag paste to replace PVD System. The electrode formation of low temperature curing Ag paste for silicon Hetero-junction solar cells is important for improving device characteristics such as adhesion, contact resistance, fill factor and conversion efficiency. The low temperature curing Ag paste is composed various additives such as solvent, various organic materials, polymer, and binder. it depends on the curing temperature conditions. The adhesion of the low temperature curing Ag paste was decided by scratch test. The specific contact resistance was measured using the transmission line method. All of the Ag electrodes were experimented at various curing temperatures within the temperature range of $160^{\circ}C-240^{\circ}C$, at $20^{\circ}C$ intervals. The curing time was also changed by varying the conditions of 10-50min. In the optimum curing temperature $200^{\circ}C$ and for 20 min, the measured contact resistance is $19.61m{\Omega}cm^2$. Over temperature $240^{\circ}C$, confirmed bad contact characteristic. We obtained photovoltaic parameter of the industrial size such as Fill Factor (FF), current density (Jsc), open-circuit voltage (Voc) and convert efficiency of up to 76.2%, 38.1 mA/cm2, 646 mV and 18.3%, respectively.

• Computers and Concrete
• /
• v.31 no.6
• /
• pp.501-511
• /
• 2023

The strengthening efficiency of biopolymer treated soil depends on biopolymer type, concentration ratio, soil type, initial water content, curing time and mixing method. In this study, the physical and mechanical properties of xanthan gum (XG) treated kaolinite were investigated through compaction test, Atterberg limit test, triaxial test and unconfined compression test. The results indicated that the optimum water content (OWC) increased from 30.3% of untreated clay to 33.5% of 5% XG treated clay, while the maximum dry density has a slight increase from 13.96 kg/m³ to 14 kg/m³ of 0.2% XG treated clay and decrease to 2.7 kg/m³ of 5% XG treated clay. Meanwhile, the plastic limit of XG treated clay increased with the increase of XG concentration, while 0.5% XG treated clay can be observed the maximum liquid limit with 79.5%. Moreover, there are the ideal water content about 1.3-1.5 times of the optimum water content achieving the maximum dry density and curing time to obtain the maximum compressive strength for different XG contents, which the UCS is 1.52 and 2.07 times of the maximum UCS of untreated soil for 0.5% and 1% XG treated clay, respectively. In addition, hot-dry mixing can achieve highest UCS than other mixing methods (e.g., dry mixing, wet mixing and hot-wet mixing).

• Structural Engineering and Mechanics
• /
• v.84 no.4
• /
• pp.465-477
• /
• 2022

The formation of biopolymer-soil matrices mainly depends on biopolymer type and concentration, soil type, pore fluid and phase transfer to influence its strengthening efficiency. In this study, the physical and mechanical properties of sodium alginate (SA) treated kaolinite are investigated through compaction test, thread rolling teat, fall cone test and unconfined compression test with considering biopolymer concentration, curing time, initial water content, mixing method. The results show that the liquid limit slightly decreases from 69.9% to 68.3% at 0.2% SA and then gradually increases to 98.3% at 5% SA. At hydrated condition, the unconfined compressive strength (UCS) of SA treated clay at 0.5%, 1%, 2% and 3% concentrations is 2.57, 4.5, 7.1 and 5.48 times of untreated clay (15.7 kPa) at the same initial water content. In addition, the optimum biopolymer concentration, curing time, mixing method and initial water content can be regarded as 2%, 28 days, room temperature water-dry mixing (RD), 50%-55% to achieve the maximum unconfined compressive strength, which corresponds to the UCS increment of 593%, compared to the maximum UCS of untreated clay (780 kPa).

• Elastomers and Composites
• /
• v.33 no.3
• /
• pp.193-200
• /
• 1998

It is well known that EPDM(ethylene propylene diene monomer) rubber has inherently excellent resistance to the weathering, ozone, heat, cold and moisture, whereas crosslinked IIR (isobutylene isoprene divlnyl benzene terpolymer) shows proper resistance to the water and gas permeation. Various characteristics of EPDM blend with crosslinked IIR such as curing characteristics, mechanical properties, dispersion of minor component and gas impermeability were explored. The optimum curing time $(t_{90})$ examined with peroxide was decreased by adding small amount of crosslinked IIR to the EPDM rubber. Mechanical properties of blends such as tensile strength, hardness and elongation at break were enhanced by increasing EPDM content. These results might be explained with the affinity of carbon black to the EPDM rubber. On the other hand, the physical properties were not changed significantly after aging, and the increase of crosslinked IIR fraction caused the decrease of compression set to small rate. EPDM rubber shows different behavior with crosslinked IIR in oxygen permeability. By adding 30wt.% crosslinked IIR to the EPDM rubber, the resistance to the oxygen permeation was improved up to three times than that of pure EPDM rubber. Conclusively, EPDM blend containing 30wt.% crosslinked IIR might be commercially applied to the o-ring and electric parts because of its proper resistance to the weathering, ozone and oxygen permeability.

• Fashion & Textile Research Journal
• /
• v.3 no.3
• /
• pp.283-289
• /
• 2001

Shrink resist finishing of wool fabric was carried out with Monoethanol aminesulphite (MONAMIN BTN) shrink resist agent after chlorination with Dichloro isocyanuric acid (DCCA). The purpose of this study is to investigate the effect of treating conditions, such as concentrations of DCCA and MONAMIN BTN, pH of treating bath, dyeing times, curing times and temperatures, on dyeing property of wool fabrics. K/S values and fastness properties of dyed wool fabrics were measured. The K/S values of dyed fabrics were increased gradually with increasing concentration, and decreased with increasing curing time. The optimum dyeing time and curing temperature were 60 min and $140^{\circ}C$, respectively. Also it seems likely that the shrink resist finishing carried out at 3% (o.w.f.) of MONAMIN BTN and pH 7 of resin treating bath is effective in increasing K/S values. Light fastness of fabric dyed was very poor and the fastness of fabric dyed was not influenced by the treatment conditions.

• Elastomers and Composites
• /
• v.56 no.1
• /
• pp.6-11
• /
• 2021

In order to develop an ultra-high-density elastomeric material for substitution of steel dynamic dampers, a new curing system and technique for high-loading of the filler were examined in this study. Mechanochemical modification of chloroprene rubber (MAH-g-CR) using an internal mixer was carried out with maleic anhydride (MAH) as a reactive monomer. The optimum amount of MAH was 10 phr and the efficient grafting of MAH on CR could be achieved at a mixing temperature of 100℃. After preparing MAH-g-CR, 50 mol% epoxidized natural rubber (ENR 50) was blended with MAH-g-CR to develop a "self-curable rubber blend system" via reaction between the functional groups of the elastomeric matrices without the curing agent and additives. The content of ENR 50 was fixed at 30 wt.% throughout evaluation of the curing behavior of the MAH-g-CR/ENR blend. Tungsten powder was added to the MAH-g-CR/ENR matrix up to 60 vol.% to obtain ultra-high-density, and the maximum density obtained was 7.57 g/㎤. Stable ts2 (scorch time) and t90 (90% cure time) could be obtained even when tungsten powder was incorporated up to 60 vol.%. In addition, the tensile strength and damping properties of MAH-g-CR/ENR containing 60 vol.% of tungsten were better than those of CR containing 60 vol.% of tungsten.