• Journal of Pharmaceutical Investigation
• /
• 제27권2호
• /
• pp.139-143
• /
• 1997

Epidermal growth factor (EGF) is a mitogen which activate the proliferation of basal cells in skin, which implicate the wound healing in severe skin damage such as burn. To carry out the preclinical test for the pharmacological action of EGF, EGF in transdermal delivery system must be stable. Since EGF is a protein susceptible to proteolysis and unstable in aqueous solution, in vitro stabilization of EGF is prerequisite for the formulation. In this study, effect of additives on the stability of EGF is investigated in vitro. The stability of EGF in aqueous solution was enhanced with the various water-soluble polysaccharides such as HPMC, sorbitol, mannitol and dextrin. EGF was successfully extracted from the ointment with 5% HPMC solution, and EGF in aqueous solution and ointment was also successfully stabilized with 5% HPMC. The ointments prepared with different amount of EGF were applied on the damaged dorsal skin of rats for the determination of optimal concentration of EGF. The ointment with EGF $(10\;{\mu}g/g)$ showed good wound healing action on the damaged skin of rats.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.183-190
• /
• 2002

In order to reduce NOx emissions in the 20kw class microturbines under development, the low NOx characteristics, as being an application to the lean premixed combustion technology, have been investigated. The study has been conducted at the conditions of high temperature and pressure. Air from a compressor with the temperature of 500K to 650K and the pressure of 0.3bar gauge to 0.7bar gauge, was supplied to the combustor through an air preheat-treatment. Sampling exhaust gases were measured at the immediate exit of the combustor. for the effect of temperature on NO and CO emissions. though NOx was increased, CO was decreased with increasing inlet air temperature. With increasing inlet air pressure, NOx and CO were increased also. NOx was decreased, but CO was increased with increasing inlet air mass flow rate. The test has been performed on the equivalent ratios of 0.10 to 0.25 in a lean region. NOx was increased with increasing equivalent ratios, but CO was decreased as an influence of flame temperature. In the very lean region of the equivalent ratio below 0.12, CO was increased suddenly, due to instability. As the results of this study, NOx and CO are found to be reduced to the similar level at the same time when operated at optimal conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제8권2호
• /
• pp.51-66
• /
• 1984

The cost percentage of engine part in the total building cost of a ship is about 30-40% and the main engine occupies about 50% of the engine part cost. For certain ships the fuel bill can be as high as about 60-70% of the total operating cost after two oil shocks and its amount for one year is nearly equivalent to her main engine price. This fact has further increased the pressure on the engine builders to develop engines of higher efficiency and better possibilities to burn further deteriorated fuel qualities. But the energy-saving plants are ordinarily more expensive and their available amount of exhaust gas energy is less and therefore, they are not always profitable and optimum systems. This paper is prepared to decide the most economical and efficient engine systems by presenting reasonable selecting and economical evaluation methods of the main engine, which is the largest single unit and the most expensive, and its auxiliaries. In order to demonstrate the application of investigated methods in a practical case, a 46, 000 DWT class bulk carrier is selected as a model ship and her main engine and its auxiliaries are selected and evaluated. The result shows that the optimum determined has one year three months POP, 0.903 IRR at a year, 4, 116, 000 dollars PW in 15 years (for 5% escalation rate of fuel cost) and 9.522 BCR for same condition, when the engine plant of a same existing ship is taken as the basis.

• Journal of Trauma and Injury
• /
• 제36권4호
• /
• pp.425-430
• /
• 2023

Axillary defects need pliable, vascular tissue to cover the critical structures traversing the axilla and to allow near-normal range of motion in the shoulder. Although local flaps are the first choice, free tissue transfer is a good option when local tissues are injured or scarred. Herein, we report two cases of axillary defects that were reconstructed using anterolateral thigh free flaps. One was a post-electric burn axillary defect for which a thoracoacromial pedicle was used as the recipient, and the other was a posttraumatic axillary defect with the transverse cervical vessels as the recipient. In both patients, the flap survived well with no complications and resulted in adequate functional recovery. In large defects of the axilla with a scarcity of local tissues, free flaps can yield optimal results. The proper selection of recipient vessels and a donor flap with adequate pedicle length impact the outcomes of such reconstruction.

• 한국정밀공학회지
• /
• 제30권1호
• /
• pp.113-119
• /
• 2013

To develop a new nuclear fuel, it needs to make a test fuel rod and carry out burn-up test in the test loop of a research reactor to check the irradiation characteristics of the nuclear fuel. At that time, several sensors such as thermocouples, LVDTs and SPNDs are needed to be attached in and out of the fuel rod and connect them with instrumentation cables. Then, the instrumentation cables deliver the signals measured by the sensors to the measuring device located outside of the reactor pool. In particular, to install a thermocouple in a fuel rod, it needs to drill off holes on the alumina blocks and sintered $UO_2$ pellets. However, because the hardness of a sintered $UO_2$ pellet is 700 Hv (or HRC 61) and that of an alumina block is 1480 Hv, a special drilling machine which adapts a diamond coated drill bit had developed. In this study, several case experiments have been carried out to find an optimal drilling condition of the drilling machine. And, using the optimal drilling condition, minimum numbers of the holes that a drill bit can drill off are verified.

• 한국수소및신에너지학회논문집
• /
• 제33권5호
• /
• pp.598-606
• /
• 2022

With the advancement of industry, the use of various sustainable energy sources and solutions to problems affecting the environment are being actively requested. From this point of view, it is intended to directly burn unused biogas to use it as energy and to solve environmental problems such as greenhouse gases. In this study, a new type of cavity matrix combustor capable of low-emission complete combustion without complex facilities such as separation or purification of biogas produced in small and medium-sized facilities was proposed, and CFD numerical calculation was performed to understand the performance characteristics of this combustor. The cavity matrix combustor consists of a burner with a rectangular porous microwave receptor at the center inside a 3D cavity that maintains a rectangular parallelepiped shape composed of a porous plate that can store heat in the combustor chamber. As a result of numerical calculation, the biogas supplied to the inlet of the combustor is converted to CO and H₂, which are intermediate products, on the surface of the 3D matrix porous burner. And then the optimal combustion process was achieved through complete combustion into CO₂ and H₂O due to increased combustibility by receiving heat energy from the microwave heating receptor.

• 한국정밀공학회지
• /
• 제32권8호
• /
• pp.681-685
• /
• 2015

Hastelloy C-276 composed of Cr, Mo, and Ni is a versatile, corrosion-resistant alloy with numerous industrial applications including its use in nuclear reactors, general chemical plants, and as a superconducting base material. Of especial significance, it can be used as a thin-sheet type whereby lap-joint welding is occasionally necessary. The main welding problems for thin-sheet metals are deformation and burn-through from an excessive heat input. Laser welding can minimize these problems because it has a high energy density and low heat effect on the base material. In this study, the laser-welding characteristics of lap-joint Hastelloy C-276 sheet metal were determined. The criteria of the laser-welding variables were chosen using a heat-conduction analysis, and the optimal welding parameters were selected by experimenting with an Nd:YAG laser.

• Advances in nano research
• /
• 제16권2호
• /
• pp.127-140
• /
• 2024

Upon direct/indirect exposure to flame or heat, composite structures may burn or thermally buckle. This issue becomes more important in the natural fiber-based composite structures with higher flammability and lower mechanical properties. The main goal of the present study was to obtain an optimal eco-friendly composite system with low flammability and high thermal buckling resistance. The studied composite consisted of polypropylene (PP) and short abaca fiber (AF) with eggshell powder (ESP) and halloysite clay nanotubes (HNTs) additives. An optimal base composite, consisting of 30 wt.% AF and 70 wt.% PP, abbreviated as OAP, was initially introduced based on burning rate (BR) and the Young's modulus determined by horizontal burning test (HBT) and tensile test, respectively. The effects of adding ESP to the base composite were then investigated with the same experimental tests. The results indicated that though the BR significantly decreased with the increase of ESP content up to 6 wt.%, it had a very destructive influence on the stiffness of the composite. To compensate for the damaging effect of ESP, small amount of HNT was used. The performance of OAP composite with 6 wt.% ESP and 3 wt.% HNT (OAPEH) was explored by conducting HBT, cone calorimeter test (CCT) and tensile test. The experimental results indicated a 9~23 % reduction in almost all flammability parameters such as heat release rate (HRR), total heat released (THR), maximum average rate of heat emission (MARHE), total smoke released (TSR), total smoke production (TSP), and mass loss (ML) during combustion. Furthermore, the combination of 6 wt.% ESP and 3 wt.% HNT reduced the stiffness of OAP to an insignificant amount by maximum 3%. Moreover, the char residue analysis revealed the distinct differences in the formation of char between AF/PP and AF/PP/ESP/HNT composites. Afterward, dilatometry test was carried out to examine the coefficient of thermal expansion (CTE) of OAP and OAPEH samples. The obtained results showed that the CTE of OAPEH composite was about 18% less than that of OAP. Finally, a theoretical model was used based on first-order shear deformation theory (FSDT) to predict the critical bucking temperatures of the OAP and OAPEH composite plates. It was shown that in the absence of mechanical load, the critical buckling temperatures of OAPEH composite plates were higher than those of OAP composites, such that the difference between the buckling temperatures increased with the increase of thickness. On the contrary, the positive effect of CTE reduction on the buckling temperature decreased by raising the axial compressive mechanical load on the composite plates which can be assigned to the reduction of stiffness after the incorporation of ESP. The results of present study generally stated that a suitable combination of AF, PP, ESP, and HNT can result in a relatively optimal and environmentally friendly composite with proper flame and thermal buckling resistance with no significant decline in the stiffness.

• Journal of Welding and Joining
• /
• 제30권3호
• /
• pp.66-70
• /
• 2012

Welding is an essential process in the automotive industry. Most welding processes that are used for auto body is spot welding. And $CO_2$ arc welding is used in a small part. In production field, $CO_2$ arc welding process is decreased and spot welding process is increased due to welding quality is poor and defects are occurred in $CO_2$ arc welding process frequently. But $CO_2$ arc welding process should be used at robot interference parts and closed parts where spot welding couldn't. $CO_2$ welding is divided into lap welding and plug arc spot welding. In case of plug arc spot welding, burn through and under fill were caused in various welding environment such as different thickness combinations of base metal, teaching point, over the two steps welding and inconsistent voltage/current. It makes some problem like poor quality of welding area and decrease the productivity. In this study, we will evaluate the effect of teaching point through the weld pool behavior and bead geometry in the arc spot welding at the plut hole. Welding position is horizontal position. And galvanized steel sheet of 2.0mm thickness that has plug hole of 6mm diameter was used. Teaching point was changed by center, top, bottom, left and right of the plug hole. At each condition, the phenomenon of weld pool behavior was confirmed using a high-speed camera. As the result, we find the center of plug hole is the most optimal teaching point. In the other teaching point, under fill was occurred at the plug hole. This phenomenon is caused by gravity and surface tension. For performance of arc spot welding at the plug hole, the teaching condition should be controlled at a center of plug hole.

• Archives of Plastic Surgery
• /
• 제50권3호
• /
• pp.315-324
• /
• 2023

Hemoglobinopathies such as sickle cell disease (SCD) are traditionally considered a relative contraindication to free tissue transfer, due to concerns that erythrocyte sickling will increase the risk of microvascular thrombosis and flap failure. This article describes a case report with the successful use of free tissue transfer in a patient with SCD and provides a systematic literature review on free tissue transfer in SCD. A retrospective chart review was performed of a patient with SCD who underwent free tissue transfer at the authors' institution. A systematic literature review using the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines was performed using the keywords "free tissue transfer," "free flap," or "microsurgery" and "sickle cell" on PubMed, Ovid/Medline, and Scopus. A 29-year-old male with delayed presentation of an electrical burn to the face and scalp underwent wound closure with a free anterolateral thigh flap. Key management principles included red blood cell transfusion to keep hemoglobin S under 30% and hemoglobin greater than 10 g/dL, maintenance of hydration, normothermia, adequate analgesia, and postoperative anticoagulation. Systematic literature review identified 7 articles describing 13 cases of free tissue transfer in 10 patients with SCD, with combined complete free flap success in 10 of the 13 flaps. Free tissue transfer can be successfully performed in patients with SCD. However, evidence on the optimal management of this unique patient population in the perioperative period after free tissue transfer is limited to case reports in the literature.