• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.461-464
• /
• 1988

In order to use mBIZ code as the practical transmission code, the information block length have to be determined. If the information block length is short, timing information disapperance is reduced, but transmission speed is increased as the result of inserted redundancy bit. While, if the information block length is long, timing information disapperance and jitter are caused. So it is very important to determine the optimal timing information block length. Therefore, in this paper, we determined the optimal information block length using S/X endurance method.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.443-454
• /
• 2016

This study focus to make 8 legs robot based on Jansen's mechanism. In the process of making, we found GL(Ground length),GAC(Ground Angle Coefficient) and the height difference of tract and compare Several models with M.Sketch to find link's Length ratio Optimised simple walking and crossing of obstacles. In the process, our team Analyzed the difference ideal tract (Jansen holy number model's track) contrived by Jansen and our final model tract. As a result, we found optimal link's length ratio to over the obstacles and some features that our model differ from Jansen holy number model. It means that optimal link's length ratio depends on certain circumstances, perfect length ratio is nonexistent.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.933-937
• /
• 2011

돔 분리형 복합재 연소관의 접합 체결부 최적의 설계 길이를 결정하기 위해 접합부 길이변화에 따른 구조해석을 수행하였다. 이때, 접착 체결부의 길이는 50mm에서 300mm의 범위를 갖는다. 무응력상태의 초기 접합부 길이대비 응력구배가 발생하는 구간의 길이를 "응력구배 길이 비"로 정의하고 이를 목적함수로 선정하였다. 구조해석 결과 접착 체결부의 길이가 200mm 이상으로 증가할 경우 응력구배 길이 비의 증가가 서서히 나타남을 확인하였다. 이는, 접착 체결부에 적용되는 2,500psi 내압에서 구조적 안전성을 확보하는 최적화된 접착 체결부의 길이가 200mm임을 의미한다.

• 한국통신학회논문지
• /
• 제36권12B호
• /
• pp.1433-1441
• /
• 2011

단일 모드 광섬유 (SMF; single mode fiber)의 색 분산과 자기 위상 변조 (SPM; self phase modulation)에 의한 신호 왜곡을 보상하기 위하여 분산 제어 (DM; dispersion management)와 광 위상 공액 (OPC; optical phase conjugation)이 적용된 파장 분할 다중 (WDM; wavelength division multiplexed) 시스템에서 전송 링크의 설계 기준을 살펴보았다. 본 연구에서 고려한 전송 링크의 설계 기준은 precompensation과 postcompensation에 의해 결정되는 최적 전체 잉여 분산 (NRD; net residual dispersion)과 채널의 최적 입사 전력 범위이다. 최적 NRD는 WDM 시스템의 전체 전송 거리와 중계 간격에 상관없이 precompensation과 postcompensation에 따라 각각 +10 ps/mn와 -10 ps/mn로 얻어졌다. 그러나 전송 거리와 중계 간격이 짧을수록 시스템 성능이 전반적으로 더욱 양호하게 나타나고, 비교적 넓은 유효 입사 전력 범위에 대해 유효 NRD 범위가 넓게 분포한다는 것을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.204-217
• /
• 2016

Modified poplar has emerged as a potential raw material for furniture production. Lack of specific modified poplar strength information; however, restricts applications in the furniture industry especially as related to strength in corner-joints. Optimization of strength in L-shaped corner dowel modified poplar joints under compression loads utilizing finite element analysis (FEA) by Taguchi method with the focus of this study. Four experiment factors (i.e., Structure Style, Tenon Length, Tenon Diameter, and Tenon Gap), each at three levels, were conducted by adopting a $L_9-3^4$ Taguchi orthodoxy array (OA) to determine the optimal combination of factors and levels for the von Mises stress utilizing ANSYS software. Results of Signal-to-Noise ratio (S/N) analysis and the analysis of variance (ANOVA) revealed the optimal L-shaped corner dowel joint in modified poplar is $45^{\circ}$ Bevel Butt in structure style, 24 mm in tenon length, 6 mm in tenon diameter, and 20 mm in tenon gap. Tenon length and tenon gap are determined to be significant design factors for affecting von Mises Stress. Confirmation tests with optimal levels and experimental test indicated the predicted optimal condition is comparable to the actual experimental optimal condition.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.442-448
• /
• 2008

This paper presents an approach to define an optimal piezoactuator length to actively control structural vibration. The optimal ratio of the piezoactuator length against beam length when a pair of piezoceramic actuator and accelerometer is used to suppress unwanted vibration with direct velocity feedback (DVFB) control strategy is not clearly defined so far. It is well known that direct velocity feedback (DVFB) control can be very useful when a pair of sensor and actuator is collocated on structures with a high gain and excellent stability. It is considered that three different collocated pairs of piezoelectric actuators (20, 50 and 100 mm) and accelerometers installed on three identical clamped-clamped beams (300 * 20 * 1 mm). The response of each sensor-actuator pair requires strictly positive real (SPR) property to apply a high feedback gain. However the length of the piezoactuator affects SPR property of the sensor-actuator response. Intensive simulation and experiment shows the effect of the actuator length variation is strongly related with the frequency range of SPR property. A shorter actuator gave a wider SPR frequency range as a longer one had a narrower range. The shorter actuator showed limited control performance in spite of a higher gain was applied because the actuation force was relatively small. Thus an optimal length ratio (actuator length/beam length) was suggested to obtain relevant performance with good stability with DVFB strategy. The result of this investigation could give important information in the design of active control system to suppress unwanted vibration of smart structures with piezoelectric actuators and accelerometers.

• 한국작물학회지
• /
• 제69권1호
• /
• pp.61-69
• /
• 2024

남부지방(진주)에서 콩 생태형에 따라 적기파종 이후 파종 시기를 달리하였을 때 온도와 일장이 생육일수 및 수량에 미치는 영향을 조사한 결과는 다음과 같다. 1. 적기파종 이후 파종시기를 달리하여 파종하였을 때 모든 생태형에서 출현일, 개화소요일수, 전체 생육일수는 단축되었다. 2. 일장과 온도가 생육일수에 미치는 영향을 다중회귀분석으로 분석한 결과 파종~개화기까지 소요일수는 일장과 온도 모두 정의 상관이였고, 개화기~수확기까지 소요일수는 일장은 정의 상관, 온도는 부의 상관이 있었다. 3. 추정 회귀모형은 파종~개화까지 소요일수(Y) = 3.177 + (0.030 × (누적일장 + 적산온도)), 개화기~수확기까지 소요일수는 (Y) = 20.945 + (0.021 × (누적일장+적산온도))인 것으로 나타났다. 4. 수량은 적기파종에서 가장 높았고 적기파종 이후 늦게 파종할수록 수량이 급격히 감소하여 조생종은 7월 20일, 중만생종은 7월 10일 이전까지는 파종을 해야 급격한 수량감소를 피할 수 있을 것으로 보인다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.28-32
• /
• 2003

Miniature inertance pulse tube refrigerator was designed and fabricated to provide optimal performance with 10W compressor. An adiabatic model was used to design an inertance pulse tube refrigerator. Among the various design parameters which should be optimized, pulse tube length and inertance tube length were considered. PdV work and various losses were calculated for various pulse tube and inertance tube length. Experiments were carried out for different pulse tube length and inertance tube length. It was shown that the experimental results were similar to the calculated results. The reason why the quantitative optimal point exists is explained.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1998년도 The Third Asian Fuzzy Systems Symposium
• /
• pp.596-700
• /
• 1998

Nowadays, with increasing many vehicles on restricted roads, the conventional traffic light creates prove startup-delaytime and end-lag-time. The conventional traffic light loses the function of optimal cycle. And so, 30∼45% of conventional traffic cycle is not matched to the present traffic cycle. In this paper proposes electrosensitive traffic light using fuzzy look up table method which will reduce the average vehicle waiting time and improve average vehicle speed. Computer simulation results prove that reducing the average vehicle waiting time which proposed considering passing vehicle length for optimal traffic cycle is better than fixed signal method which doesn't consider vehicle length.

• 한국기계가공학회지
• /
• 제17권2호
• /
• pp.118-123
• /
• 2018

Coil guns are known worldwide as inexpensive space launch vehicles. The principle of Fleming's right-hand rule allows the coil gun to accelerate the projectile by applying enormous voltage to the solenoid coil. This study was performed to improve the speed of the coil gun using MATLAB, a commercially available numerical program for high launching force of electromagnetic projectiles. To maximize the speed of the projectile, the largest coil of American wire gauge was used, and the number of windings in the radial and axial directions of the solenoid coil was optimized. Optimal length of the projectile was obtained by calculating the optimal aspect ratio between the axial length of the solenoid coil and the length of the projectile.