• Structural Monitoring and Maintenance
• /
• 제9권1호
• /
• pp.59-80
• /
• 2022

In the present study, the objective is to detect the structural damages using the responses obtained from the sensors at the optimal location under uncertainty conditions. Reducing the error rate in damage detection process due to responses' noise is an important goal in this study. In the proposed algorithm for optimal sensor placement, the noise of responses recorded from the sensors is initially reduced using the principal component analysis. Afterward, the optimal sensor placement is obtained by the damage detection equation based sensitivity analysis. The sensors are placed on degrees of freedom corresponding to the minimum error rate in structural damage detection through this procedure. The efficiency of the proposed method is studied on a truss bridge, a space dome, a double-layer grid as well as a three-story experimental frame structure and the results are compared. Moreover, the performance of the suggested method is compared with three other algorithms of Average Driving Point Residue (ADPR), Effective Independence (EI) method, and a mass weighting version of EI. In the examples, young's modulus, density, and cross-sectional areas of the elements are considered as uncertainty parameters. Ultimately, the results have demonstrated that the presented algorithm under uncertainty conditions represents a high accuracy to obtain the optimal sensor placement in the structures.

• 소음진동
• /
• 제10권4호
• /
• pp.648-654
• /
• 2000

A procedure to determine the realizable optimal positions of rigid supports is suggested to get a maximum fundamental natural frequency. a measured frequency response function based substructure-coupling technique is used to model the supported structure. The optimization procedure carries out the eigenvalue sensitivity analysis with respect to the stiffness of supports. As a result of such stiffness optimization, the optimal rigid-support positions are shown to be determined by choosing the position of the largest stiffness. The optimally determined support conditions are verified to satisfy the eigenvalue limit theorem. To demonstrate the effectiveness of the proposed method, the optimal support positions of a plate model are investigated. Experimental results indicate that the proposed method can effectively find out the optimal support conditions of the structure just based on the measured frequency response functions without any use of numerical model of the structure.

• 한국식품저장유통학회지
• /
• 제8권2호
• /
• pp.157-163
• /
• 2001

Optimal conditions for hot water extraction of Liriope spicata tuber were investigated with changes in solvent ratio(2∼6 fold) and heating time(1∼5 hr) by response surface methodology. The content of extractable solids increased with an increased in solvent ratio, and the highest content showed at heating time of 3 hr. The content of total steroid saponin increased with a decrease in solvent ratio, and increased with an increase in heating time at increasing the solvent ratio. The content of non-reducing sugar containing oligosaccharides at a lower solvent ratio didn’t show changes depending on heating time, while that at a higher ration decreased with an increase in heating time. Optimal extraction conditions using hot water as the limited conditions of 15∼18% extractable solids, 1.5∼2.0% total steroid saponin, 6∼8% reducing sugar, 6∼7% non-reducing sugar and 13∼15 brix were 3 hrs of heating time and 4 fold of solvent ratio.

• Journal of applied mathematics & informatics
• /
• 제20권1_2호
• /
• pp.209-224
• /
• 2006

This paper presents an optimization model with performance constraints for two kinds of graph elements layout problem. The layout problem is partitioned into finite subproblems by using graph theory and group theory, such that each subproblem overcomes its on-off nature about optimal variable. Furthermore each subproblem is relaxed and the continuity about optimal variable doesn't change. We construct a min-max problem which is locally equivalent to the relaxed subproblem and develop the first order necessary and sufficient conditions for the relaxed subproblem by virtue of the min-max problem and the theories of convex analysis and nonsmooth optimization. The global optimal solution can be obtained through the first order optimality conditions.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.248-251
• /
• 1999

The optimal reaction conditions are determined for a PET process, which consists of transesteriflcation, prepolymerization and polycondensation reactors in series. Based on the simulation results of the reactor system, we scrutinize the cause and effect between the reaction conditions and the final properties of the polymer product. We then select the process variables with significant influence on the properties of polymer as control variables and calculate the optimal reaction conditions by iterative dynamic programming (IDP) algorithm with constraints. A new reaction scheme incorporating reactions for by-products as well as three main reactions is considered in the constrained IDP method.

• Environmental Engineering Research
• /
• 제20권2호
• /
• pp.121-125
• /
• 2015

Biohydrogen production from food waste via dark fermentation was conducted by using mixed culture under various environmental conditions (initial pH, initial F/M ratio, initial ferrous iron ($Fe^{2+}$), and temperature condition) in batch reactor. The results revealed that the maximum hydrogen yield of $46.19mL\;H_2/g\;COD_{add}$ was achieved at the optimal conditions (initial pH 8.0, initial F/M ratio 4.0, initial iron concentration 100 mg $FeSO_4/L$ and thermophilic condition ($55{\pm}1^{\circ}C$)). Furthermore, major volatile fatty acid (VFA) productions of butyrate (765.66 mg/L) and acetate (324.69 mg/L) were detected and COD removal efficiency was detected at 66.00%. Therefore, these optimal conditions could be recommended to operate a system.

• Journal of applied mathematics & informatics
• /
• 제23권1_2호
• /
• pp.243-256
• /
• 2007

This paper deals with determining the sufficient conditions of minimum for the class of problems in which the necessary conditions of optimum are satisfied in the strengthened form Legendre-Clebsch. To this paper, we shall use the sweep method which analysis the conditions of existence of the conjugated points on the optimal trajectory. The study we have done evaluates the command variation on the neighboring optimal trajectory. The sufficient conditions of minimum are obtained by imposing the positivity of the second variation. The results that this method offers are applied to the problem o the orbital rendez-vous for the linear case of the equations of movement.

• 산업경영시스템학회지
• /
• 제38권3호
• /
• pp.14-20
• /
• 2015

It is important to understand psychological and physiological responses of occupants who seated in a chair in order to shape a comfortable indoor official environment. So it is needed to find out optimal seated conditions. The purpose of this study was to explore optimal condition of seat air conditioning control based on psychological or subjective responses (perceived temperature and comfort sensation) and physiological responses (heartrate variability; HRV). To do this, experimental conditions were designed by the difference of indoor temperature and seat air conditioning temperature. In the experiment 1, seven experimental conditions were designed with one control condition which was not used seat air conditioning system, and six experimental conditions which the difference of indoor temperature and seat air conditioning temperature ($-1^{\circ}C{\sim}-6^{\circ}C$). In the experiment 2, four experimental conditions were designed with one control condition and three experimental conditions ($-3^{\circ}C{\sim}-5^{\circ}C$). In addition, participants' psychological or subjective response was measured by CSV (comfort sensation vote) and PTS (perceived temperature sensitivity) as a psychological or subjective response, and heartrate variability was measured as a physiological response. As a result, in the experiment 1, it was reported that the optimal conditions of seat air conditioning control based on participants' psychological or subjective comfort were from $-3^{\circ}C$ to $-5^{\circ}C$ experimental conditions. In addition, in the experiment 2, it was reported that the optimal condition of seat air conditioning control based on participants' physiological comfort was $-4^{\circ}C$ experimental condition. These results suggested that seat air conditioning could affected to comfort sensation of occupants in an appropriate range, rather than unconditionally.

• 한국응용과학기술학회지
• /
• 제41권1호
• /
• pp.46-57
• /
• 2024

In this study, the various process conditions for high-power DC Magnetron Sputtering (DCMS) on the surface roughness of carbon thin films were investigated. The optimal conditions for Si/C coating were 40min for deposition time, which does not deviate from normal plasma, to obtain the maximum deposition rate, and the conditions for the best surface roughness were -16volt bias voltage and 400watt DC power with 1.3x10-3torr chamber pressure. Under these optimal conditions, an excellent carbon thin film with a surface roughness of 1.62nm and a thickness of 724nm was obtained. As a result of XPS analysis, it was confirmed that the GLC structure (sp² bonding) was more dominant than the DLC structure (sp³ bonding) in the thin film structure of the carbon composite layer formed by DC sputtering. Except in infrequent cases of relatively plasma instability, the lower bias voltage and applied power induces smaller surface roughness value due to the cooling effect and particle densification. For the optimal conditions for Graphite/C composite layer coating, a roughness of 36.3 nm and a thickness of 711 nm was obtained under the same conditions of the optimal process conditions for Si/C coating. This layer showed a immensely low roughness value compared to the roughness of bare graphite of 242 nm which verifies that carbon coating using DC sputtering is highly effective in modifying the surface of graphite molds for glass forming.

• 한국농공학회지
• /
• 제28권2호
• /
• pp.42-52
• /
• 1986

This study involves the estimation of optimal ranges of parameters for a linear watershed model. A well-known TANK model was chosen and a linear combination of four tanks assumed. The model was used to simulate daily streamflow for six watersheds of different sizes and by a trial-and-error approach a set of optimal parameters defined. The parameters were related to watershed sizes and land use conditions. Optimal parameters for ungaged conditions were defined from the relationships; daily streamflow simulated and compared to the observed date. The simulated results were in a general agreement with the data.