• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.401-403
• /
• 2006

When RF overlay technology is used in EPON-based optical access network, there coexist the directly modulated 1310-nm upstream data, the directly modulated 1490-nm downstream data, and the amplitude-modulated l550-nm downstream broadcast signal based on RF overlay technology. In this paper, we analyze the spectrum of 8B/10B IDLE line code signal and the SRS effect of l490-nm IDLE line code signal on 1550-nm signal. From the result of analysis, we propose a new technique that can be used to improve the CNR of the broadcast signal, which is based on self synchronous scramble method.

• Journal of the Optical Society of Korea
• /
• v.16 no.1
• /
• pp.1-5
• /
• 2012

This paper describes a 150-Mb/s monolithic optical receiver for plastic optical fiber link using a standard CMOS technology. The receiver integrates a photodiode using an N-well/P-substrate junction, a pre amplifier, a post amplifier, and an output driver. The size, PN-junction type, and the number of metal fingers of the photodiode are optimized to meet the link requirements. The N-well/P-substrate photodiode has a 200-${\mu}m$ by 200-${\mu}m$ optical window, 0.1-A/W responsivity, 7.6-pF junction capacitance and 113-MHz bandwidth. The monolithic receiver can successfully convert 150-Mb/s optical signal into digital data through up to 30-m plastic optical fiber link with -10.4 dBm of optical sensitivity. The receiver occupies 0.56-$mm^2$ area including electrostatic discharge protection diodes and bonding pads. To reduce unnecessary power consumption when the light is not over threshold or not modulating, a simple light detector and a signal detector are introduced. In active mode, the receiver core consumes 5.8-mA DC currents at 150-Mb/s data rate from a single 3.3 V supply, while consumes only $120{\mu}W$ in the sleep mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.4 s.95
• /
• pp.410-417
• /
• 2005

In this paper, optical noise is reduced by a differential detector with a plastic optical fiber bundle in a wireless optical interconnection. A plastic optical fiber bundle divides the received optical signal equally and connects it to two photodiodes. In this configuration two photodiodes effectively detect the optical signal at one point, and the output voltage variation due to the abrupt change of optical noise distribution in space disappears. The signal to noise ratio in a differential detector with a fiber bundle was improved to be $10\;\cal{dB}$ higher than in a single photodiode with an optical filter.

• Korean Journal of Remote Sensing
• /
• v.26 no.5
• /
• pp.581-591
• /
• 2010

In this paper, we proposed a new wavelet-based image fusion algorithm, which has advantages in both frequency and spatial domains for signal analysis. The developed algorithm compares the ratio of SAR image signal to optical image signal and assigns the SAR image signal to the fused image if the ratio is larger than a predefined threshold value. If the ratio is smaller than the threshold value, the fused image signal is determined by a weighted sum of optical and SAR image signal. The fusion rules consider the ratio of SAR image signal to optical image signal, image gradient and local variance of each image signal. We evaluated the proposed algorithm using Ikonos and TerraSAR-X satellite images. The proposed method showed better performance than the conventional methods which take only relatively strong SAR image signals in the fused image, in terms of entropy, image clarity, spatial frequency and speckle index.

• Experimental Neurobiology
• /
• v.26 no.5
• /
• pp.241-251
• /
• 2017

Saturation mutagenesis was performed on a single position in the voltage-sensing domain (VSD) of a genetically encoded voltage indicator (GEVI). The VSD consists of four transmembrane helixes designated S1-S4. The V220 position located near the plasma membrane/extracellular interface had previously been shown to affect the voltage range of the optical signal. Introduction of polar amino acids at this position reduced the voltage-dependent optical signal of the GEVI. Negatively charged amino acids slightly reduced the optical signal by 33 percent while positively charge amino acids at this position reduced the optical signal by 80%. Surprisingly, the range of V220D was similar to that of V220K with shifted optical responses towards negative potentials. In contrast, the V220E mutant mirrored the responses of the V220R mutation suggesting that the length of the side chain plays in role in determining the voltage range of the GEVI. Charged mutations at the 219 position all behaved similarly slightly shifting the optical response to more negative potentials. Charged mutations to the 221 position behaved erratically suggesting interactions with the plasma membrane and/or other amino acids in the VSD. Introduction of bulky amino acids at the V220 position increased the range of the optical response to include hyperpolarizing signals. Combining The V220W mutant with the R217Q mutation resulted in a probe that reduced the depolarizing signal and enhanced the hyperpolarizing signal which may lead to GEVIs that only report neuronal inhibition.

• Journal of the Optical Society of Korea
• /
• v.2 no.1
• /
• pp.22-25
• /
• 1998

We present a spectrum broadening technique to improve the signal-to-noise ratio of spectrum sliced incoherent light sources using the fiber four-wave mixing effect which occurs in a nonlinear loop mirror located at the receiver. The initial transmission channel bandwidth of 0.92 nm was increased to 1.62 nm in the nonlinear loop mirror at the optical receiver, which enhances the signal-to-noise ratio to a desired value. Using this technique, we have demonstrated the transmission of a 2.5 Gb/s NRZ signal with the 0.92 nm bandwidth through a 80 km dispersion-shifted fiber. The measured transmission penalty was less than 0.2 dB at $1{\imes}10^{-10}$ BER.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.103-109
• /
• 2003

We have proposed the 4-Dimensional Multiple-Subcarrier Modulation with fixed bias in Optical Wireless Communications. Here, the 4-D signal vectors are derived from the optimization technique of signal waveforms maximizing the minimum distance between signal points in an n-dimensional Euclidean sphere. The resulting vectors are used in generating the output amplitude of impulse generator in a Multiple-Subcarrier Modulation scheme. We have achieved that the normalized power requirement of the proposed system is maximum 3 dB and 3.3 dB smaller than those of normal QPSK, Reserved Subcarrier, and Minimum Power scheme, respectively. Also, in the range of 1.125 ∼ 1.25 of the normalized bandwidth, the proposed system has maximum 3 dB, 2 ∼ 4 dB, 0 ∼ 3 dB smaller bandwidth requirement compare to normal QPSK, Res. Subcarrier, Min. Power schemes, respectively.

• Current Optics and Photonics
• /
• v.2 no.5
• /
• pp.413-421
• /
• 2018

We propose a novel methodology based on the multiplication function to improve the signal-to-noise ratio (SNR) for vibration detection in a phi optical time-domain reflectometer system (phi-OTDR). The extreme-mean complementary empirical mode decomposition (ECEMD) is designed to break down the original signal into a set of inherent mode functions (IMFs). The multiplication function in terms of selected IMFs is used to determine a vibration's position. By this method, the SNR of a phi-OTDR system is enhanced by several orders of magnitude. Simulations and experiments applying the method to real data prove the validity of the proposed approach.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.156-167
• /
• 2021

In this paper, we propose a digital transceiver unit design for in-building of 5G optical repeaters that extends the coverage of 5G mobile communication network services and connects to a stable wireless network in a building. The digital transceiver unit for driving the proposed 5G optical repeater is composed of 4 blocks: a signal processing unit, an RF transceiver unit, an optical input/output unit, and a clock generation unit. The signal processing unit plays an important role, such as a combination of a basic operation of the CPRI interface, a 4-channel antenna signal, and response to external control commands. It also transmits and receives high-quality IQ data through the JESD204B interface. CFR and DPD blocks operate to protect the power amplifier. The RF transmitter/receiver converts the RF signal received from the antenna to AD, is transmitted to the signal processing unit through the JESD204B interface, and DA converts the digital signal transmitted from the signal processing unit to the JESD204B interface and transmits the RF signal to the antenna. The optical input/output unit converts an electric signal into an optical signal and transmits it, and converts the optical signal into an electric signal and receives it. The clock generator suppresses jitter of the synchronous clock supplied from the CPRI interface of the optical input/output unit, and supplies a stable synchronous clock to the signal processing unit and the RF transceiver. Before CPRI connection, a local clock is supplied to operate in a CPRI connection ready state. XCZU9CG-2FFVC900I of Xilinx's MPSoC series was used to evaluate the accuracy of the digital transceiver unit for driving the 5G optical repeater proposed in this paper, and Vivado 2018.3 was used as the design tool. The 5G optical repeater digital transceiver unit proposed in this paper converts the 5G RF signal input to the ADC into digital and transmits it to the JIG through CPRI and outputs the downlink data signal received from the JIG through the CPRI to the DAC. And evaluated the performance. The experimental results showed that flatness, Return Loss, Channel Power, ACLR, EVM, Frequency Error, etc. exceeded the target set value.

• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.53-58
• /
• 2018

A novel X-band high speed frequency sweep signal generator based on a tunable optoelectronic oscillator (OEO) incorporating a frequency-swept laser is presented and the theoretical fundamentals of the design are explained. A prototype of the generator with tuning range from 8.8552 GHz to 10.3992 GHz and a fine step about 8 MHz is achieved. The generated radiofrequency signal with a single sideband (SSB) phase noise lower than -100 dBc/Hz@10KHz is experimentally demonstrated within the whole tunable range, without any narrow RF band-pass filters in the loop. And the tuning speed of the frequency sweep signal generator can reach to over 1 GHz/s benefiting from applying a novel dispersion compensation modular instead of several tens of kilometers of optical fiber delay line in the system.