• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1086-1089
• /
• 2003

We investigated the electro-optical (EO) performances of the super twisted nematic liquid crystal display (STN-LCD) on the polyimide (PI) surface using polymer film. Monodomain alignment of the plastic STN-LCD can be observed. A stable voltage-transmittance (V-T) curve of the plastic STN-LCD was observed on the polyimide (PI) surfaces using polymer film. Also, a faster response time for the plastic STN-LCD on the polyimide (PI) surfaces using polymer film can be achieved. Therefore, the EO performances of the plastic STN-LCD on the polyimide (PI) surfaces using polymer film is almost the same as that of the glass STN-LCD on a polyimide (PI) surface.

• Journal of the Optical Society of Korea
• /
• 제18권6호
• /
• pp.799-808
• /
• 2014

The mechanism of optical interaction of two nanoholes, milled in an opaque gold film, by means of surface plasmon polariton (SPP) propagation is investigated. The interaction depends on the polarization direction of the incident light when the nanohole pair is illuminated through uniform single antenna excitations. It is shown that by illuminating one of the nanoholes, under single antenna excitation, the other nanohole can be excited indirectly via propagated SPPs from the excited nanohole. In addition, it is found that the spectrum of electromagnetic power above the surface of the metallic film at an arbitrary point along the axis of the nanohole pair presents two resonant peaks. These peaks are due to the optical interaction between nanoholes, where the short- and long-wavelength peaks can be assigned to in-phase and antiphase interactions of magnetic dipoles relative to each nanohole, respectively. The magnetic coupled dipole approximation (MCDA) method confirms the simulation results.

• Current Optics and Photonics
• /
• 제1권2호
• /
• pp.101-106
• /
• 2017

Optical structures of a tapered ultra-thin light guide film (LGF) were optimized by optical simulation for increasing coupling efficiency between light sources and the LGF. A serration pattern on the entrance side surface could provide a comparable coupling efficiency to that of the conventional LGF where a linear, asymmetric prism array was formed on the taper surface. Several micro-patterns were applied to the top and/or bottom surface of the LGF for achieving better luminance property, and it was found that an optimized micro-pyramid pattern exhibited the highest average luminance together with satisfactory luminance uniformity.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1191-1194
• /
• 2003

At present, the fabrication of optical filter for optical communication mostly depends on handwork, and only a few companies are propelling semi-automatic systems compounded with automatic and hand-operated methods. The measurement evaluation of optical filters is not commonly useful, so it causes difficulties in the producing field. And the packaging process becomes a very unstable process because the filters are judged from the results that they are not measured and immediately packaged during that process. In this situation, the automatic assembly system of optical filter for communication is extremely important and has begun to make its appearance as the most necessary technology for developing optical communication component with high-functionality. In this paper, we constructed systems of assembly and performance evaluation for micro optical collimator. And by using that, we designed a system capable of performance evaluation and assembly of film filter of about 30 $\mu\textrm{m}$ thickness as well as optical filter for common communication.

• 대한전자공학회논문지
• /
• 제19권6호
• /
• pp.17-32
• /
• 1982

집적광학용 광도파전에 전기팡 효파 혹은 자기광 효과를 나타내는 이방성 매질을 사용할 때 매질정수 및 박막두께등 광학적 변수가 모드 변환에 미치는 영향괼 엄밀한 파동광학의 접근 방법으로 조사하여 어떠한 박막형 광도파관 구조에도 적용될 수 있는 일반적인 해석방법을 제시하였다. 균일한 이방성 매질에서의 고유 모드와 그 구성성분 및 위상속도를 먼저 결정하고 그 결과를 이용하여 박자형 광도파관에서의 고유 모드 성분에 대한 위상특성식을 구하였고 전자파의 진행방향에 대한 모드 성분의 변화를 Jones 행열 령태로 표시하여 박막형 광도파관에서 모드 젼환의 조건과 그 변환율이 Bulk 매질에서와는 다름을 나타내었다. Wave propagation in gyrotropic or anisotropic medium is analyzed in terms of the eigenmodes of the medium, which are admixture of TE and TM waves. The field composition and the phase velocity of the modes are also determined. The results of the analysis are applied to thin film optical waveguide using such medium as substrate and/or film. Based on the characteristic equations for phase constants of the waveguide, the condition for TE-TM mode convection is derived, and wave propagation in the guide is represented in the form of Jones matrix, which allows a new interpretation in the conversion efficiency of the thin-film optical waveguides.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.233-233
• /
• 2010

CdS thin films were deposited on glass substrates by R.F. magnetron sputtering method and some of the samples were treated by rapid thermal annealing (RTA) process. Effects of thermal annealing on structural and optical properties were investigated at different temperatures ranging from 100 to $600^{\circ}C$. The crystallographic structure of the films and the size of the crystallites in the films were studied by X-ray diffraction. The crystallite sizes were found to increase, and the X-ray diffraction patterns were seen to sharpen by annealing. Optical properties of the films were calculated using the envelope method and the photoluminescence measurements. The optical properties of the films were seen to be dependent on the film thicknesses. The energy gap of the films was found to decrease by annealing. The band edge sharpness of the optical absorption was seen to oscillate by thermal annealing. Annealing over $400^{\circ}C$ was seen to degrade the optical properties of the film. The best annealing temperature for the films was found to be $400^{\circ}C$ from the optical properties. It is observed that the CdS film annealed at $400^{\circ}C$ reveals the strongest UV emission intensity and narrowest full width at half maximum among the temperature ranges studied. The enhanced UV emission from the film annealed at $400^{\circ}C$ is attributed to the improved crystalline quality of CdS thin film due to the effective relaxation of residual compressive stress and achieving maximum grain size. The results show that heat treatments under optimal annealing condition can provide significant improvements in the properties of CdS thin films.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.151-153
• /
• 2005

Indium tin oxide (ITO) thin film was polished by chemical mechanical polishing (CMP) by the change of process parameters for the improvement of electrical and optical properties of ITO thin film. Light transparent efficiency of ITO thin film was improved after CMP process at the optimized process parameters compared to that before CMP process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.354-355
• /
• 2005

Indium tin oxide (ITO) thin film was polished by chemical mechanical polishing (CMP) by the change of process parameters for the improvement of electrical and optical properties of ITO thin film. Light transparent efficiency of ITO thin film was improved after CMP process at the optimized process parameters compared to that before CMP process.

• 한국전기전자재료학회논문지
• /
• 제21권4호
• /
• pp.376-380
• /
• 2008

The optical properties of multi layered thin films with $Sb_2O_3/Na_3AlF_6/Sb_2O_3/Cr$ were simulated by using EMP(Essential Macleod Program). EMP is a comprehensive software package to design and analyse the optical characteristics of multi-layered thin film. $Sb_2O_3$ and $Na_3AlF_6$ were selected as a high refractive index and low refractive index material respectively. Additionally Cr was chosen as mid reflective material. Optical properties including color effect were systematically studied in terms of different optical thickness of low refractive index material. The optical thickness of $Na_3AlF_6$ was changed as 0.25, 0.5, 0.75 and $1.0\lambda$. The film with 0.25, 0.5, 0.75 and $1.0\lambda$ of optical thickness showed mixed color range between purple and red range, yellowish green and bluish green, purple and mixed color range of green and purple respectively.

• Journal of the Optical Society of Korea
• /
• 제10권1호
• /
• pp.1-10
• /
• 2006

Optical transparency and high diffraction efficiency are two essential factors for high performance of the photopolymer. Optical transparency mainly depends on the miscibility between polymer binder and photopolymerized polymer, while diffraction efficiency depends on the refractive index modulation between polymer binder and photopolymerized polymer. For most of organic materials, the large refractive index difference between two polymers accompanies large structural difference that leads to the poor miscibility and thus poor optical quality via light scattering. Therefore, it is difficult to design a high-performance photopolymer satisfying both requirements. In this work, first, we prepared a new phase-stable photopolymer (PMMA) with large refractive index modulation and investigated the optical properties. Our photopolymer is based on modified poly (methyl methacrylate) as a polymer binder, acryl amide as a photopolymerizable monomer, triethanolamine as initiator, and yellow eosin as a photosensitizer at 532 nm. Diffraction efficiency over 85% and optical transmittance over 90% were obtained for the photopolymer. Second, Organic-inorganic nanocomposite films were prepared by dispersing an aromatic methacrylic monomer and a photo- initiator in organic-inorganic hybrid sol-gel matrices. The film properties could be controlled by optimizing the content of an organically modified silica precursor (TSPEG) in the sol-gel matrices. The photopolymer film modified with the organic chain (TSPEG) showed high diffraction efficiency (> 90%) under an optimized condition. High diffraction efficiency could be ascribed to the fast diffusion and efficient polymerization of monomers under interference light to generate refractive index modulation. The TSPEG modified photopolymer film could be successfully used for holographic memory.