• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.777-781
• /
• 2002

Recently, an optical disc system has been proposed using blue laser diode, high NA objective lens and groove only disc structure. A new method is needed to readout CD and DVD in this blue system. In order to readout CD and DVD in HD-DVD system, we adopted dual-lenses actuator in consideration of optical utilization efficiency, optical performance and insurance of sufficient W.D (working distance). This dual-lenses actuator has two objectives in radial direction, one is for CD/DVD and the other is for HD-DVD. We had to solve the induced problems of DC tilt increase, $2^{nd}$ resonance deterioration and AC sensitivity drop caused by disposing two lenses in an actuator. Especially, to solve AC sensitivity drop, we introduced two 2-pole magnets and separated focus and track magnetic circuits. Consequently we presented that dual-lenses actuator has been possessed good performance. And we measured eye patterns of CD, DVD and HD-DVD by using HD-DVD optical pick-up with dual-lenses actuator.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.5
• /
• pp.385-393
• /
• 2004

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(voice coil motor) for coarse motion, for an SFF ODD(small form factor optical disk drive), in order to achieve fast access speed and precise track-following control. Over the past few decades there have been a lot of researches related to the VCM and dual-stage actuator. In this paper, we focus our attention on the design and control of the PZT actuator. Due to the dual cantilever structure. the PZT actuator can generate precise translational tracking motion at its tip to which an optical pickup is attached. and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing it with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.424-429
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.2
• /
• pp.121-126
• /
• 2005

Recently, an optical disc system has been proposed using blue laser diode, high NA objective lens and groove only disc structure. A new method is needed to readout CD and DVD in this Blu-Ray Disc Recorder. In order to readout CD and DVD in Blu-Ray Disc Recorder, we adopted dual-lenses actuator in consideration of optical utilization efficiency, optical performance and insurance of sufficient W.D(working distance). This dual-lenses actuator has two objectives in radial direction, one is for CD/DVD and the other is for BD. We had to solve the induced problems of collision between disc and lens, DC tilt increase, AC tilt increase, 2nd resonance deterioration and AC sensitivity drop caused by disposing two lenses in an actuator. Also we developed high response twin- objective actuator with radial tilt function to apply high-speed BD Recorder or BD Player. Consequently we presented that two kinds of dual-lenses actuators for BD Recorder have been possessed good performance in 3 axis directions. And we measured eye patterns of CD, DVD and BD by using one BD optical pick-up with dual-lenses actuator.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.117-124
• /
• 2005

This study developes the vibration model to estimate the vibration energy of compact disc player's mainbase assembly which is supported by dampers and springs, and this model is verified by experiment. From frequency response function, we investigate the natural frequency and mode shape in the up/down direction for mainbase assembly. In order to determine the analysis frequency band, we investigate the excitation frequency of road from the vehicle test. As the characteristics of dampers and springs are changed, we carry out the sensitivity analysis of vibration energy for mainbase assembly which include optical pick-up and feeding system. And we found out that the properties of damper were dominant element in the vibration energy of mainbase assembly's CG(center of gravity).

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.5
• /
• pp.462-466
• /
• 2008

This paper proposes a stable gain scheduling method of linear time invariant controllers for tracking servo system. In order to read and write the data on the optical disc, the pick-up head should be moved to the exact track quickly and follow the track immediately. Two different controllers are used for each moving and track-following. In pull-in period, a transition period from moving to track-following, the head might slip and miss the target track. This brings on another searching process and increases the total time. One way to avoid slipping is to extend the bandwidth of the track-following controller. But, extending the bandwidth could degrade the following performance. More prevalent way is to use one more controller in this pull-in period and switch to the following controller. In general, however, switching or scheduling of stable controllers cannot guarantee the stability. This paper suggests an scheduling method guaranteeing the overall stability not only in a generalized form but also in special form for SISO system. The sufficient condition is derived from the fact that Q factor of a stable controller should be stay in $RH_{\infty}$ space. In the experiment, the proposed method shows better performance than the switching method such as shorter time and lower current consumption.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.1157-1164
• /
• 2003

Dynamic Load/unload (L/UL) mechanism is an alternative to the contact start stop (CSS) technology which eliminates stiction and wear failure modes associated with CSS. Other benefits of L/UL include increased areal density due to smooth disk surfaces, thinner overcoats, and lower head flying height Improved shock resistance due to elimination of head slap, and reduced power consumption. Inertia latch mechanism becomes important for mobile disk drives because of non operating shock performance. Various types of latch designs have been introduced in hard disk drives to limit a rotary actuator from sudden uncontrolled motion. In this paper, a single spring inertia latch is introduced for a small form optical disk drive, which uses a rotary actuator for moving an optical pick-up. A new small inertia latch with single spring is designed to ensure both feasible and small size. The shock performance of the new inertia latch is experimentally verified.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.2
• /
• pp.115-120
• /
• 2005

As a popularity of a portable digital device such as a cellular phone, a digital camera and a MP3 player is spreading, the demand of the mobile storage device increases rapidly. A bluray technology using 405nm laser diode and objective lens having high NA(Numerical Aperture), 0.85, satisfies a miniaturization and a high capacity which are the requirements of the portable device. To develop SFFOP(small form factor optical pickup), it is prerequisite to minimize the number of optical components and establish evaluation and assembly method of micro optical pickup system as well as mass production method of micro optical component. To minimize optical elements of optical pickup, there have been many researches to use P-HOE(Polarized Holographic Optical Element) due to its extremely small size and versatile function. However, P-HOE is handled and assembled very accurately in SFFOP. In this paper, static error signal detection method is developed for an alignment of P-HOE in SFFOP. Using developed static error signal detection method, P-HOE can be aligned very accurately with real time result of static error signals of pickup such as FES(focusing error signal) and TES(Tracking Error Signal). The developed static error signal detection method is verified by the evaluation of commercialized DVD Pickup. And finally. developed static error signal detection method is applied for the assembly of P-HOE in SFFOP system satisfies specification of BD(Blu-ray Disk).

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.501-504
• /
• 1987

The photoconductor is made of evaporated amorphous selenium as the base material, doped with arsenic and tellurium to prevent crystallization and to increase the red sensitivity of the amorphous selenium. The four-layered photoconductor of Se-As-Te has good photosensitivity(r=0.9) and high dark resistivity($P_d=10^{12}{\Omega}{\cdot}cm$). therefore, this four-layered photoconductor can be used for the target of color image pick-up tube.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.2
• /
• pp.156-162
• /
• 2006

In this paper, we have investigated the disc warping in high-speed slim-type optical disc drive. The track density as well as high rotational speed of the information storage devices must be increased to enhance their recording capacity and data transfer rate. Generally, ODD used in the Lap-top computer has small inner space. So, the flow instability of the inner space is increased rapidly with its rotational speed. In extreme case, the flow instability may cause the malfunction of the read/write pick-up of drives. The experiments and numerical analysis were carried out for several cases and the result shows the influence of airflow to the disc warping.