• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.775-779
• /
• 2001

In optical disk drive (ODD), disk rotation speed has been increasing rapidly to achieve high data transfer rate. High servo bandwidths for focusing and tracking actuator are required to follow dynamic disturbance by high rotation speed in ODD. However, the servo bandwidth is significantly limited by some vibration modes which are induced by the flexibility of moving part. In this work, the vibration modes affecting bandwidth of actuators are suppressed by modifying actuating force by VCM. For this, the relation between the horizontal component of the actuating force and vibration mode is analyzed and force characteristic affecting to vibration mode is obtained through electromagnetic and structural analysis using simulation program.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2092-2099
• /
• 2013

Through the data transfer race in industry since 1990s, the operational speed of optical disk drive(ODD) becomes commonly over 10,000 rpm. Such high speed operation inevitably causes the vibration, which is also the disturbances in the read-write process of pick-up servo-controller. Generally the vibration disturbance problem can be solved by the vibration isolation using the rubber mount and the increase of robustness of the pick-up servo-controller. Optical disk itself has not been targeted for the vibration reduction, because it is manufactured under the standardized format. In this paper we focused on the increase of critical speed of optical disk, that is, the improvement of dynamic characteristics, with the control of residual stresses which are come from the injection molding process. To do this, first, the residual stresses induced from the injection molding process are calculated using finite element method. The major design parameters of the process conditions are flow rate and melt temperature, which control the residual stresses in optical disk. Second, the critical speed of optical disk is calculated with modal analysis considering residual stress distributions. It was found out that the critical speed can be improved by the control of operational parameters in the injection molding process.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.676-681
• /
• 2003

In this paper, we investigated the disc warping in high-speed slim-type optical disc drive. Recently, the information storage devices are increasing track density and higher rotation speed to enhance their recording capacity and their data transfer rate. Generally, ODD used in the Lap-top Computer has small inner space. So, the flow instability of inner space is rapidly increased as its higher rotation speed. An extreme case, the flow instability causes the malfunction of readout at pick-up of drives. The experiments and numerical analysis were carried out for several cases, the result shows the influence of airflow to the disc warping.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.1-22
• /
• 2005

There are two important trends in the modern information society, including digital networking and ubiquitous environment. Thus it is strongly required to develop new information storage devices such as high density storages to match the increased data capacity and small size storage devices to be applied to the mobile multimedia electronics. So far, many approaches have been studied for the high density memory, including the holographic memory, super-RENS and near-field recording using solid immersion lens (SIL) or nano-probe for the ODD (Optical Disk Drive) system, and the perpendicular magnetic recording and heat-assisted magnetic recording for the HDD (Hard Disk Drive) system. In addition, new mobile storage devices have been prepared using 0.85" HDD and 30mm ODD systems from a lot of foreign and domestic companies and institutes. In this paper, the recent technology trend for the next generation information storage system is summarized to offer a research motivation and encouragement to new researchers in this field with an emphasis on the technical issues of the increase of data capacity and decrease of device size.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.34.2-34
• /
• 2001

There are many control methods guaranteeing the robustness of systems. Among them, H$\infty$ control, sliding mode control and disturbance observer have been used widely. Especially, disturbance observer(DOB) is one of the most popular methods because it is easy to apply and the cost to pay is low due to its simplicity. Conventional DOB utilizes output signal as a feedback signal. But in Optical Disk Drive(ODD) systems, the Position Error Signal(PES) is the only available one. So conventional DOB is not applicable. If we use error signal in stead of output signal, another form of DOB is made. We call it as Error based Disturbance Observer(EDOB). We show in this paper the difference between two systems, namely conventional DOB system and the EDOB system, and also show the effectiveness of EDOB through experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.87.4-87
• /
• 2001

In this paper, a design guideline of disturbance observer(DOB) for track-following controller is presented. In the track-following control system(TFCS) of optical disk drive(ODD), disturbance rejection is the key issue for the overall performance. DOB gives an excellent advantage of disturbance rejection within its bandwidth determined by a low-pass filter. In general, design of DOB requires a tradeoff between performance and stability, which should be based on quantitative analysis. The external disturbance is well-defined in the frequency domain, which provides the base of the analysis. In addition to a DOB, a proper feedback controller is utilized for guaranteeing overall stability. Some computer simulations and experiments are conducted and some of the results are presented.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.1
• /
• pp.66-71
• /
• 2004

Airborne contaminant particles are intruded into optical disk drive(ODD) due to the flow caused by disk rotation and can be adhered to objective lens, which causes read/write errors. Such a phenomenon can be a serious problem for high-density storage devices. The purpose of this paper is to understand the effect of particle contamination of objective lens in a CD-ROM drive on laser diode power and photo diode RF signal. The measurements of laser power and readout RF signal were carried out by using a laser power meter and a time interval analyzer, respectively. The parameters for estimating a readout-signal' distortion were its jitter and amplitude. Alumina(Al$_2$O$_3$) particles were used as test dust particles. The results show that the failure for data access happened as the degree of lens contamination was greater than 20％.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.3
• /
• pp.208-213
• /
• 2006

The present state of the design of swing arm actuators for optical disc drives is to obtain the high efficient dynamic characteristics within a very compact volume. As a necessary consequence, the need of the small form factor (SFF) storage device has been arisen as major interests in the information storage technology. In this paper, we suggest the miniaturized swing arm type actuator that has high efficient dynamic characteristics for SFF optical disk drive (ODD). For the operating mechanism, it uses a tracking electromagnetic (EM) circuit for a focusing motion together. Moreover, due to the size constraint, the thermal stability of optical head is important. Therefore, the actuator is designed to emit the heat, which is generated by optical pick-up, along the actuator body easily. Initial model is designed based on the topology optimization method considering the thermal conductivity. Then, the structural parts of the actuator are modified to maintain the high sensitivity and to have wide control bandwidth by the design of experiments method (DOE) and new concept of decreasing mass and inertia. Finally, a swing arm type actuator for SFF ODD is suggested and its dynamic characteristics are verified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.780-785
• /
• 2003

Recently the trends in information storage devices need small size, mobility, high capacity, and low power consumption etc. To satisfy those, the development of high performance actuator is an important issue. Compared with general linear actuator for optical disk drive, swingarm type rotary actuator is suitable to design in small form factor and has fast access time for random access. Swingarm actuator is designed considering the structural problem and the actuating force of VCM(Voice Coil Motor). The increase of mass caused by optical components makes vibration problems of swing-arm, therefore resonance frequency should be increased and inertia has to be reduced. ANSYS FEM tool is employed in optimizing swingarm. The VCM is designed using 3-D electro-magnetic analysis, and parameters of magnetic circuit are determined to matte large flux density. The large flux density enables to achieve low power consumption. VCM holder is designed to get the mass balance of total actuator and this balance reduces the magnitude of critical mode relative to pivot bearing, It is expected that swingarm type rotary actuator designed by this method is available to variable type of micro optical disk drives.