• ETRI Journal
• /
• v.38 no.4
• /
• pp.665-674
• /
• 2016

We designed and fabricated a semiconductor optical amplifier-integrated dual-mode laser (SOA-DML) as a compact and widely tunable continuous-wave terahertz (CW THz) beat source, and a pin-photodiode (pin-PD) integrated with a log-periodic planar antenna as a CW THz emitter. The SOA-DML chip consists of two distributed feedback lasers, a phase section for a tunable beat source, an amplifier, and a tapered spot-size converter for high output power and fiber-coupling efficiency. The SOA-DML module exhibits an output power of more than 15 dBm and clear four-wave mixing throughout the entire tuning range. Using integrated micro-heaters, we were able to tune the optical beat frequency from 380 GHz to 1,120 GHz. In addition, the effect of benzocyclobutene polymer in the antenna design of a pin-PD was considered. Furthermore, a dual active photodiode (PD) for high output power was designed, resulting in a 1.7-fold increase in efficiency compared with a single active PD at 220 GHz. Finally, herein we successfully show the feasibility of the CW THz system by demonstrating THz frequency-domain spectroscopy of an ${\alpha}$-lactose pellet using the modularized SOA-DML and a PD emitter.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.423-430
• /
• 1994

We designed and fabricated the single mode fiber pigtailed DFB-LD module for 2.5 Gbps optical communication system. In the design of the DFB-LD module, we made the module divided into two parts of inner sub-module and outer 14-pin butterfly package and cylindrical shaped sub-module contain quasi confocal 2 lens system including optical isolator and electrical connection between these parts via hybrid substrate of bias T circuit. Laser welding was used to assemble the sub-module which requires accurate fixing between optical elements. The fabricated DFB-LD module showed optical coupling efficiency of 20% and - 3 dB small signal response of more than 2.6 GHz. We confirmed mechanical reliability of the module by temperature cycle test where the tested module exhibit optical power fluctuation of less than 10%. Finally we evaluated the performance of the fabricated DFB-LD module as light source of 2.5 Gbps optical communication system, sensitivity of - 30.2 dBm was obtained through 47 km optical fiber transmission under the criterion of $1\times10^{-10}$ BER and transmission penalties were 1.5 dB caused by extinction ratio and 1.0 dB caused by chromatic dispersion of normal single mode fiber. fiber.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.487-496
• /
• 2014

In this study, three kinds of polymers based on phenothiazine-benzothiadiazole were synthesized by a Suzuki coupling reaction, and the various side-chains were substituted at the nitrogen of phenothiazine. The optical and electrochemical properties of synthesized polymers were analyzed. The results indicate that their absorption ranged from 300 to 700 nm, and also confirmed the ideal highest occupied molecular orbital (HOMO) energy level was about -5.4 eV with low band-gap energy. Photovoltaic devices were fabricated using a photoactive layer composed of a blended solution of the polymer and $PC_{71}BM$ in ortho-dichlorobenzene The device with P2HDPZ-bTP-OBT containing the branched side-chain and long chain showed the best performance; the maximum power conversion efficiency of this device was 2.4% (with $V_{OC}$ : 0.74 V, $J_{SC}$ : $6.9mA/cm^2$, FF : 48.0%).

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.441-446
• /
• 2007

Outcoupling efficiency of the OLED device is improved by incorporating both a microlens array and a diffractive grating pattern. The microlens array improves the light transmission at the interface of glass and air, and the diffractive grating outcouples the guided mode propagating at the waveguide, which consists of ITO and organic layers. By using the PDMS soft mold imprinting method, the microlens array is fabricated on the glass substrate. The diffractive grating pattern is directly fabricated on the ITO surface by using laser interferometry. A microlens array with a diameter of $10{\mu}m$ improves the light coupling efficiency by 22%. The diffractive grating made of TSMR photoresist enhances the luminance power efficiency by 41% at a current density of $20mA/cm^2$.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.166-172
• /
• 1994

The fiber optic receiver, ETRI APD-FET 1.0, is developed for the application of optical communication. This fiber optic receiver includes PD sub-module and pre-amplifier case. A single lens system is introduced for the PD sub-module. The sub-module consists of the avalenche photodiode(APD), GRIN rod lens, and a single mode fiber. The above components are enclosed into the stainless steel 304L housings. By bevelling the fiber end, the single mode fiber provides less than ~ 28 dB of optical return loss. The area of image focus is controlled by adjusting the length of spacer located in-between the fiber and the GRIN rod lens. The laser welding technique is applied to achieve the maximum coupling efficiency for the joining of each housing. In the pre-amplifier case, GaAs FET pre-amplifier workes for photocurrent amplification and the thermister is mounted to control the APD bias. The performance of ETRI APD-FET1.0 shows the sensitivity of - 30.3 dBm at $10^{-10}$ BER(bit error rate) and 2.5 Gbps optical random signal of $2^{23}-1$ word length. The fiber optic receiver is one of the essensial parts of the transmission module for B-ISDN. Also, the above optical packaging technology will be adapted for the developement of 10 Gbps transmission application 2.5 Gbps 5 Gbps

• Korean Journal of Optics and Photonics
• /
• v.12 no.4
• /
• pp.289-293
• /
• 2001

A metal capillary splice fiber-optic sensor was fabricated for use as an intensity-based macro-bending sensor. As the radius of curvature due to the macro-bending decreases, the angular misalignment of the fiber ends inside the metal capillary increases, i.e., the coupling efficiency of the fiber splice is reduced. Thus, macro-bending can be detected by the measurement of the reduction of transmitted power. The detectable range of macro-bending. was measured approximately from 20 mm to 85 mm. The center wavelengths of the fiber Bragg gratings are 1543.3 nm and 1549.5 nm, respectively. The maximum bending loss of this sensor was measured about -11.92 dB. Using this metal capillary spliced fiber sensor and fiber Bragg gratings, macro-bending detection has been demonstrated, and it is shown to have potential for multi-point macro-bending sensors. nsors.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.327-330
• /
• 2003

We present the fabrication and measured performance of a wavelength tunable Butt coupled DBR-LD. An average coupling efficiency between active layer and passive waveguide layer was measured over 85％per facet, and the average threshold current was 21 ㎃ for the waveguide integrated DBR laser. High output power of Butt coupled DBR-LD was obtained over 25 ㎽. As high as 25 ㎽ of output power was achieved by the butt coupled method. The maximum wavelength tuning range is about 7.4 nm, and the side mode suppression ratio was more than 40 ㏈ using 1.3 ${\mu}{\textrm}{m}$ InGaAsP waveguide layer.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.11
• /
• pp.18-26
• /
• 1999

Recently, various simplified simulation techniques such as firite-difference beam propagation method and non-orthogonal coupled-mode theory have proposed to analyze the optical characteristics of tapered directional couplers supported by the coupling of two propagating modes. Although these approaches are often in sufficiently accurate, they do not provide the detailed solutions encountered in the analysis of tapered guiding structures. For this purpose, we introduce and utilize a newly developed modal transmission-line theory to analyze rigorously power transfer of the directional coupler. The numerical result reveals that the propagation constants of even and odd modes converge to a single value as increasing the spacer thickness between two symmetric tapered guides. Furthermore, 97% of the power incident into a guiding channel is transmitted to the other channel at the tapered angle ${\theta}=0.1^{\circ}$, and the efficiency of power transfer decreases dramatically as increasing the angle.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1414-1420
• /
• 2013

Five novel spiro[benzo[c]fluorene-7,9'-fluorene] based dyes, including 5-[spiro[benzo[c]fluorene-7,9'-fluoren]-5-yl] spiro[benzo[c]fluorene-7,9'-fluorene] (7), 5-[spiro[benzo[c]fluorene-7,9'-fluoren]-9-yl] spiro[benzo[c]fluorene-7,9'-fluorene] (8), 5-[spiro[benzo[c]fluorene-7,9'-fluoren]-2'-yl] spiro[benzo[c]fluorene-7,9'-fluorene] (9), 9-[spiro[benzo[c]fluorene-7,9'-fluoren]-9-yl] spiro[benzo[c]fluorene-7,9'-fluorene] (10), and 2'-[spiro[benzo[c]-fluorene-7,9'-fluoren]-2'-yl] spiro[benzo[c]fluorene-7,9'-fluorene] (11) were successfully prepared from the corresponding halogen and boronic acid derivatives through the Suzuki coupling reaction, respectively. Chemical structures were confirmed by $^1H$ nuclear magnetic resonance (NMR), $^{13}C$ NMR, Fourier transforminfrared spectrscopy, mass spectroscopy, and elemental analysis. The thermal properties were determined by differential scanning calorimetry and thermal gravimetric analysis. The relationships between the optical and electrochemical properties and the combined positions between these dimers were systematically investigated using UV-vis, photoluminescence (PL), and photoelectron spectroscopy. These five dimers exhibited high fluorescent quantum yields and good morphological stability with high glass transition states > $174^{\circ}C$. Dimer 7 showed a UV absorbance peak at 353 nm, emission PL peak at 424 nm, and quantum efficiency of 0.62 in a cyclohexane solution.

• Korean Journal of Optics and Photonics
• /
• v.10 no.4
• /
• pp.311-317
• /
• 1999

Unidirectional single-mode operation of a diode-pumped Nd:YAG laser with a planar semimonolithic ring cavity has been demostrated at 1064 nm. The semimonolithic cavity consists of a laser active medium placed in a magnetic field, a crystal quartz plate, and an output coupling mirror. They form an optical diode by acting each part as a Faraday rotator, a reciprocal polarization rotator and a partial polarizer, respectively. An eigenpolarization theory for the cavity configuration was presented and losses for the eigenmodes were calculated. A pump-limited single-mode output power of 155 mW and a slope efficiency of 17% were obtained when the laser was pumped by a 1.2 W, 809 nm diode-laser. A laser linewidth of less than 100 kHz is inferred from a beat note frequency spectrum between two identical laser systems and continous single-mode tuning range was more than 2 GHz.