• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.247-251
• /
• 1998

This work presents the analysis of $1\times2$ polymer waveguide thermo-optic switch using asymmetric Y-splitter at the wavelength of 1300nm. Because of the high thermo-optic coefficient of polymeric materials the design of efficient switches were feasible. For the numerical simulation of these switches the finite difference beam propagation method has been employed. Design rules for a $1\times2$ polymeric switch have been defined by using the numerical techniques.

• Journal of Sensor Science and Technology
• /
• v.31 no.4
• /
• pp.194-213
• /
• 2022

This study comprehensively reviewed four types of integrated-optic electric-field sensors based on titanium diffused lithium-niobate waveguides: symmetric and asymmetric Mach-Zehnder interferometers, 1×2 directional couplers, and Y-fed balanced-bridge Mach-Zehnder interferometers. First, we briefly explain the crystal properties and electro-optic effect of lithium niobate and the waveguide fabrication process. We theoretically analyzed the key parameters and operating principles of each sensor and antennas. We also describe and compare the design, simulation, implementation, and performance tests: dc and ac characteristics, frequency response, dynamic range, and sensitivity. The experimental results revealed that the sensitivity of the sensor based on the Y-fed balanced bridge Mach-Zehnder interferometer (YBB-MZI) was higher than that of the other types of sensors.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.411-414
• /
• 2008

The study is about simulation of optical circuit for oneself performance evaluation of Fiber Optic Gyro(FOG) closed-loop controller board. The Fiber Optic Interferometer Simulator is used a digital signal processing for cosine response specificity output of fiber optic coil about input rate. Response specificity of the fiber optic coil is $Vo(t)=K3[1+\cos\{K1(Vm(t)-Vm(t-{\tau}))+K2\}]$. Also the Fiber Optic Interferometer Simulator is able to confirm a output value with K1, K2 and K3 input. The fiber Optic Interferometer Simulator is able to oneself performance evaluation without fiber optical circuit. Because, it is the very same cosine response specificity of real fiber optic coil about input rate.

• Journal of the Optical Society of Korea
• /
• v.18 no.4
• /
• pp.335-340
• /
• 2014

Based on Zernike polynomial fitting, we propose an algorithm believed to be new for interferometric measurements of rotationally asymmetric surface deviation of optics. This method tests and calculates each angular surface by choosing specified rotation angles with lowest error. The entire figure can be obtained by superimposing these sub-surfaces. Simulation and experiment studies for verifying the proposed algorithm are presented. The results show that the accuracy of the proposed method is higher than single-rotation algorithm and almost comparable to the rotation-averaging algorithm with fewer rotation measurements. The new algorithm can achieve a balance between the efficiency and accuracy.

• Journal of KSNVE
• /
• v.6 no.4
• /
• pp.475-479
• /
• 1996

Recently, fiber optic hydrophone is a subject which has attracted as a underwater acoustic sensor. In this paper, a length of optical fiber is bonded to an end-capped hollow cylinder of some elastic material, e. g. aluminum and glass-pyres. The normalized sensitivity is derived according to the direction of polarization. Derived sensitivity equations are simulated for two different mandrel materials. The results are also compared to the McMahon's results which calculated for an average Pockel coefficient. Based on the numerical simulation normalized sensitivity is propotional to the inner to outer diameter ratio.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.4
• /
• pp.437-442
• /
• 2014

Due to electrical cross-coupling between modulation voltage and photodetector output in a closed-loop fiber optic gyro, deadzone inevitably occurs. In this paper, deadzone error by cross-coupling effect was analyzed and the overcoming method was suggested. Simulation and measurement results show the main reason for deadzone is mainly related to electrical cross-coupling, and it can be effectively reduced by square-wave dithering method.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.7
• /
• pp.2891-2903
• /
• 2020

Phase-generated carrier (PGC) demodulation algorithm is the main demodulation methods in Fiber-optic interferometric sensors (FOISs). The conventional PGC demodulation algorithms are influenced by the carrier phase delay between the interference signal and the carrier signal. In this paper, an automatic carrier phase delay synchronization (CPDS) algorithm based on orthogonal phase-locked technique is proposed. The proposed algorithm can calculate the carrier phase delay value. Then the carrier phase delay can be compensated by adjusting the initial phase of the fundamental carrier and the second-harmonic carrier. The simulation results demonstrate the influence of the carrier phase delay on the demodulation performance. PGC-Arctan demodulation system based on CPDS algorithm is implemented on SoC. The experimental results show that the proposed algorithm is able to obtain and eliminate the carrier phase delay. In comparison to the conventional demodulation algorithm, the signal-to-noise and distortion ratio (SINAD) of the proposed algorithm increases 55.99dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10B
• /
• pp.1707-1713
• /
• 2000

We have proposed a tunable optical ADM using a fiber-optic transversal filter which is composed of fiber couplers and metal-film coated fiber-optic tapped delay-lines with a flat spectral response in abroad range of wavelength. Simulation results show that the optical loss at the DROP and PASS wavelengths of the OADM is negligible and the wavelength tunability is 0.78${\mu}{\textrm}{m}$/ps for the unit time delay of 2 ps. In order to investigate the effects of wavelength drift of the imput optical signal on the OADM the loss at the DROP port and the crosstalks to the other ports have been calculated. The maximum bit rates have been calculated at 46.26 Gb/s for the input Gaussian pulse width of 10 ps.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.908-913
• /
• 2003

We have performed computer simulation to obtain electro-optic characteristics of reflective hybrid aligned nematic liquid crystal displays (LCDs) driven by fringe field. The results show that the optimal retardation value (dΔn) of the cell is 0.289 ${\mu}$m, which allows for the cell to have a practical cell gap of larger than 3 ${\mu}$m when manufacturing. A reflectance of the dark state is only 0.114 % for an incident light 550 nm. At this condition, the light efficiency of white state reaches 92.7 %. The display with optimized cell parameters shows that the contrast ratio greater than 5 exists over 600 of polar angle in all directions and lower driving voltage than that of fringe-field driven homogeneously aligned reflective LCD.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.2
• /
• pp.93-98
• /
• 2015

This study focuses on simulation technology in the injection molding process for plastic optic lenses. The CAE program 3D TIMON was used to predict retardation, flow patterns and warpage deformation. The results were compared to the results of optic lenses as measured using the WPA-100 retardation measurement device with injection molding CAE for retardation predictions. According to the analysis and measured results, the distributions of retardation between the CAE results and the measurement results were similar. It was also confirmed that varying the injection speed had an effect on the injection pressure, warpage deformation and retardation distribution. As the injection speed increases, the injection pressure also increases and warpage deformation decreases. However, as the injection speed increases, the retardation distribution deteriorates.