• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.789-797
• /
• 2021

The worldwide sizes of container ships are rapidly increasing. The container ship size in 2005, which was about 9,200 TEU has increased to 24,000 TEU in recent times. In addition to the increase in the sizes of the container ships, the arrivals/departures of large container vessels to/from Korea have also increased. Hence, the necessity for reviewing safe passage of such vessels is emphasized. In the present study, a 24,000 TEU container vessel was used as a model ship to calculate the under-keel clearance (UKC) at Gadeok Channel through which vessels must pass to arrive at Busan New Port, in accordance with the Korean Port and Fishing Port Design Standards and Commentary. In addition, the maximum allowable speed that meets UKC standards was calculated using various squat formulas, whose results were then compared with the current speed limit standards. The analysis results show that Busan New Port requires 10% marginal water depth, and the squat that meets this requirement is 0.95 m. Gadeok Channel requires 15% marginal water depth, and the squat that meets this requirement is 1.78 m; in this case, the maximum allowable speed is calculated as 15 kts. Busan New Port has set the speed limit as 12 kts, which is higher than the calculated 11 kts. Thus, speed limit reconsideration is required in terms of safety. However, the set speed limit for Gadeok Channel is 12 kts, which is lower than the calculated 15 kts. Thus, additional considerations may be provided to increase the speed limits for smooth navigational passage of vessels. The present study, however, is constrained by the fact that it reflects only a limited number of elements in the UKC and allowable speed calculations; therefore, more accurate UKC and safe speed values can be suggested based on extended studies to this research.

• Journal of Bio-Environment Control
• /
• v.30 no.4
• /
• pp.383-392
• /
• 2021

It has been known that oyster mushrooms cultivated in facilities with thermal insulation have been strongly affected by inner environments. Forced air-circulation fans exert much direct influence on disturbing air inside the facility so the matter is of particular interest. This study is carried out to investigate the measured levels of air uniformity in a cultivation facility for oyster mushroom in the various cases that reversibly controlled air-circulation fans which drove the flow in the upward and reverse direction by turn and unidirectional fans by which the wind blew upwards only were operated from July 1 to 10. The actual survey for the selection of ongoing operation cases presented that farmers, even though there were some discrepancies, have made use of fans in a way that it paused for 5-30min after running for 5-15min by turn. The level of air uniformity in the case of adopting reversible fans revealed a slight difference of 1.4-1.8℃ (Temp.) and 7.8-8.7% (R.H.) under the condition of not using a cooler during the investigation period. By contrast, unidirectional fans showed a noticeable difference of 3.2-3.7℃ and 14.0-15.4%, which meant that air uniformity driven by reversible fans much more increased compared to that for unidirectional fans. Among the twenty operational applications considered for reversible fans, the circumstance that the wind blew upwards for 10-15min and ceased for 5-10min and blew again in the reverse direction for 10-15min in succession gave minor improvements at the level of air uniformity, but at present there was somewhat difficult to make decision on which cases were optimally best. It seems necessary that the effects of reversible fans on air uniformity as well as qualities of oyster mushrooms have to be appraised in the cultivation period and the flow visualization needs to be done to ascertain the performance of air mixture.

• Journal of Korea Water Resources Association
• /
• v.54 no.12
• /
• pp.1339-1348
• /
• 2021

In accordance with the River Law, the basic river maintenance plan is established every 5-10 years with a considerable national budget for domestic rivers, and various river surveys such as the river section required for HEC-RAS simulation for flood level calculation are being conducted. However, river survey data are provided only in the form of a pdf report to the River Management Geographic Information System (RIMGIS), and the original data are distributedly owned by designers who performed the river maintenance plan in CAD format. It is a situation that the usability for other purposes is considerably lowered. In addition, when using surveyed CAD-type cross-sectional data for HEC-RAS, tools such as 'Dream' are used, but the reality is that time and cost are almost as close as manual work. In this study, RAUT (River Information Auto Upload Tool), a tool that can solve these problems, was developed. First, the RAUT tool attempted to automate the complicated steps of manually inputting CAD survey data and simulating the input data of the HEC-RAS one-dimensional model used in establishing the basic river plan in practice. Second, it is possible to directly read CAD survey data, which is river spatial information, and automatically upload it to the river spatial information DB based on the standard data model (ArcRiver), enabling the management of river survey data in the river maintenance plan at the national level. In other words, if RIMGIS uses a tool such as RAUT, it will be able to systematically manage national river survey data such as river section. The developed RAUT reads the river spatial information CAD data of the river maintenance master plan targeting the Jeju-do agar basin, builds it into a mySQL-based spatial DB, and automatically generates topographic data for HEC-RAS one-dimensional simulation from the built DB. A pilot process was implemented.

• Journal of the Korean Orthopaedic Association
• /
• v.53 no.6
• /
• pp.505-512
• /
• 2018

Purpose: Many reconstruction methods have been attempted after an en-bloc resection of the proximal humerus. In particular, the introduction of reverse shoulder arthroplasty (RSA) has made a breakthrough in the functional recovery of the shoulder. Nevertheless, RSA has limitations when the humeral bone stock loss is significant. In addition, it is unclear if RSA is effective in patients showing failure with non-operative treatment of a proximal humeral tumor. Materials and Methods: A reconstruction was performed using an overlapping allograft-RSA composite for 11 patients with a failed proximal humeral construct. Delayed RSA was performed on 6 patients with failed non-operative treatment. The pre- and postoperative Musculoskeletal Tumor Society (MSTS) score and the complications were addressed. Results: Overlapping allograft-RSA composite afforded a stable construct in 11 failed proximal humeral reconstructions and the patient's chief complaints were resolved. The mean time to the union of overlapped allograft-host junction was 5.5 months. Average preoperative MSTS score of 20.3 point increased to 25.7 point, postoperatively. Four of the six patients who had RSA within 4 years from the index operation showed arm elevation of more than $90^{\circ}$ whereas the remaining 5 patients showed some disability. The complications include one case each of dislocation and aseptic infection, which were resolved by changing the polyethylene liner and scar revision, respectively. None of the 6 patients who underwent delayed RSA after the failure of non-operative treatment showed arm elevation more than $90^{\circ}$. Conclusion: An overlapping allograft-RSA composite is a simple and reliable reconstructive modality in patients with massive bone loss. In patients with metastatic cancer necessitating a surgical resection at presentation, early conversion to RSA is recommended to secure functional recovery.

• Journal of Bio-Environment Control
• /
• v.28 no.1
• /
• pp.46-54
• /
• 2019

Experiments of local cooling and heating on crown and root zone of forcing cultivation of strawberry 'Seolhyang' using heat pump and root pruning before planting were conducted. During the daytime, the crown surface temperature of the crown local cooling treatment was maintained at $18{\sim}22^{\circ}C$. This is suitable for flower differentiation, while those of control and root zone local cooling treatment were above $30^{\circ}C$. Budding rate of first flower clusters and initial yields were in the order of crown local cooling, root zone local cooling and control in root pruning plantlet and non pruning plantlet, except for purchase plantlet. Those of root pruning plantlet were higher than those of non pruning plantlet. These trends were evident in the yield of the first flower cluster until February 14, 2018, and the effect of local cooling and root pruning decreased from March 9, 2018. The budding rates of the second flower cluster according to the local cooling and root pruning treatments were not noticeable compared to first flower cluster but showed the same tendency as that of first flower cluster. In the heating experiment, root zone local heating(root zone $20^{\circ}C$+inside greenhouse $5^{\circ}C$) and crown local heating(crown $20^{\circ}C$+inside greenhouse $5^{\circ}C$) saved 59% and 65% of heating fuel, respectively, compared to control(inside greenhouse $9^{\circ}C$). Considering the electric power consumption according to the heat pump operation, the heating costs were reduced by 55% and 61%, respectively.

• Journal of Environmental Impact Assessment
• /
• v.30 no.1
• /
• pp.35-48
• /
• 2021

In this study, the assessment of field applicability of in-situ remediation of nitrate-contaminated groundwater located in Yesan-gun was performed. Zero-valent iron/bio composite media injected PRB (Permeable Reactive Barrier) and monitoring well were installed in the contaminated groundwater site and monitored main remediation indicators during the PRB operation. Nitrate, nitrite, ammonia, Fe ion, TOC, and turbidity were analyzed and the diversity and population of microorganism in the PRB installed site were investigated for the verification of effect of injected PRB. In the study site where is an agricultural area, a river flows from west to east that forms a river boundary and the southern area has an impermeable sector. It was found that nitrate flows into the river, which is similar as groundwater flow. Simulation result for the fate of nitrate in groundwater showed steady state of nitrate arrived after 3~5 years passed. However, it is just to consider current conditions with no additional input of contaminant source, if additional input of contaminant source occurs contamination dispersion and time for steady state are expected to be increased. The monitoring results showed that Fe ion, TOC and turbidity in groundwater were not clearly changed in concentration after PRB installation, which indicates adaptability of the injected PRB for remediation of groundwater with no additional harmful effect to water quality. The concentration of nitrate maintained less than 5mg/L until 42 days after PRB installation and recovered its initial concentration after 84 days passed and showed termination of reactivity of injected zero-valent iron/bio composite media for removal nitrate. Nitrite and ammonia ions found after installation of PRB indicates reductive removal of nitrate. And the outstanding increase of microorganism diversity and population of Betaproteobacteria Class which includes denitrification microorganism explains biologically reductive removal of nitrate in injected PRB.

• Atmosphere
• /
• v.31 no.2
• /
• pp.229-240
• /
• 2021

The Global Ocean Data Assimilation and Prediction System (GODAPS) in operation at the KMA (Korea Meteorological Administration) is introduced. GODAPS consists of ocean model, ice model, and 3-d variational ocean data assimilation system. GODAPS assimilates conventional and satellite observations for sea surface temperature and height, observations of sea-ice concentration, as well as temperature and salinity profiles for the ocean using a 24-hour data assimilation window. It finally produces ocean analysis fields with a resolution of 0.25 ORCA (tripolar) grid and 75-layer in depth. This analysis is used for providing a boundary condition for the atmospheric model of the KMA Global Seasonal Forecasting System version 5 (GloSea5) in addition to monitoring on the global ocean and ice. For the purpose of evaluating the quality of ocean analysis produced by GODAPS, a one-year data assimilation experiment was performed. Assimilation of global observing system in GODAPS results in producing improved analysis and forecast fields with reduced error in terms of RMSE of innovation and analysis increment. In addition, comparison with an unassimilated experiment shows a mostly positive impact, especially over the region with large oceanic variability.

• The Journal of Korean Philosophical History
• /
• no.54
• /
• pp.9-42
• /
• 2017

It is as necessary as ever to make constant efforts to overcome the regional strife between the eastern and western parts of Korea and come to a mutual understanding. To achieve this, we must endeavor to correct Korean people's distorted understanding of the history of Korean philosophical thoughts. Ordinary Koreans commonly and mistakenly associate the academic circles of Korean Neo-Confucianism with certain regions by which to divide them into Giho School and Yongnam School and then go as far as associating the schools and parties and pegging them 'Namin'(南人) to refer to as the followers of Yongnam School and 'Seoin'(西人) as the followers of Giho School. Such false notions must be corrected. During the reign of King Seonjo, political factions of Joseon were split into Yongnam and Giho, or East and West. At the time, the two cardinal directions East and West were only used to refer to the eastern and western parts of Seoul, and not Yeongnam(East) and Giho(West) of the Korean Peninsula. Therefore, the factional split at the time has nothing to do with regional cleavages. In fact, a majority of scholars representing Korean Neo-Confucianism maintained a friendly relationship regardless of the school, party, and region. Many leading scholars in the middle of the Joseon Dynasty namely Jo Sik(曺植)/Seong Woon(成運), Lee Hwang(李滉)/Ki DeaSeung(奇大升), Lee Hwang(李滉)/Lee Yi(李珥), Noh Susin (盧守愼)/Lee Yi, the ones in the late Joseon Dynasty -Jeong Gyeong Se(鄭經 世)/Kim Jang-Saeng(金長生), Jeong Gyeong Se(鄭經世)/Song Joon Gil(宋浚吉), and also those at the end of the Joseon Dynasty such as Kwak JongSeok(郭鍾錫) and Kim BokHan(金福漢) deeply respected each other and had a close friendship rooted in their academic commitment. The friendship between the leaders of Giho and Yongnam is a testimony to the high level of their character, academic achievement, and intellect. More than ever, such intangible intellectual and cultural resources drawn from Korean tradition must be utilized to the fullest. From this point on, we need to further promote the friendship and mutual understanding the scholars of Yongnam(Gyeongsang-do), Gyeonggi, Honam (Jeolla-do), and Hoseo(Chungcheong-do) enjoyed, and use them as a cognitive basis for harmony between the eastern and western parts of the country. These invaluable assets can be specifically used in the promotion of exchange between the local autonomous governments of the regions where above-mentioned scholars built an amicable relationship, joint commemorative events, exchange between families of the scholars of both regions, opening of special exhibitions dedicated to the harmony between Yongnam and Giho at museums in the two regions, co-organization of local festivals, joint operation of culture programs, and relationship and exchange between the 'seowons' in both regions, through which to promote the long history of exchange between the scholars of the past and utilize it in joint projects.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.1
• /
• pp.206-219
• /
• 2021

The warming of the climate is increasing the damage caused by termites to wooden buildings, cultural properties and houses. A group removal system can be installed around the building to detect and remove termite damage; however, if the site is not visited regularly, every one to two months, you cannot observe whether termites have spread within, and it is difficult to take prompt effective action. In addition, since the system is installed and operated in an exposed state for a long period of time, it may be ineffective or damaged, resulting in a loss of function. Furthermore if the system is installed near a cultural site, it may affect the aesthetic environment of the site. In this study, we created a detection system that uses wood, cellulose, magnets, and magnetic sensors to determine whether termites have entered the area. The data was then transferred to a low power LoRa Network which displayed the results without the necessity of visiting the site. The wood was made in the shape of a pile, and holes were made from the top to the bottom to make it easier for termites to enter and produce a cellulose sample. The cellulose sample was made in a cylindrical shape with a magnet wrapped in cellulose and inserted into the top of a hole in the wood. Then, the upper part of the wood pile was covered with a stopper to prevent foreign matter from entering. It also served to block external factors such as light and rainfall, and to create an environment where termites could add cellulose samples. When the cellulose was added by the termites, a space was created around the magnet, causing the magnet to either fall or tilt. The magnetic sensor inside the stopper was fixed on the top of the cellulose sample and measured the change in the distance between the magnet and the sensor according to the movement of the magnet. In outdoor experiments, 11 cellulose samples were inserted into the wood detection system and the termite inflow was confirmed through the movement of the magnet without visiting the site within 5 to 17 days. When making further improvements to the function and operation of the system it in the future, it is possible to confirm that termites have invaded without visiting the site. Then it is also possible to reduce damage and fruiting due to product exposure, and which would improve the condition and appearance of cultural properties.

• Microbiology and Biotechnology Letters
• /
• v.48 no.4
• /
• pp.525-532
• /
• 2020

A continuous fermentation process was carried out to enhance hyaluronic acid (HA) production using Streptococcus zooepidemicus cells. During the 1st stage continuous operation from 8 h with a dilution rate of 0.029/h (D1), HA was produced in the range of 7.5-10 g/l. During the 2nd stage from 44 h with a dilution rate of 0.036/h (D2), HA production (8.28 g/l) was initially reduced to a small extent due to increase of dilution rate from D1 to D2, and then a new pseudo-steady state was formed within a few hours with a concurrent small variations of HA production. The HA amount produced during the latter part of the 2nd stage was stably maintained in the range of 8.28-9.48 g/l, about 4.7% less amount compared to the 1st stage. Due to 24% increase of dilution rate from D1 to D2, however, maximum volumetric productivity (DP) amounting to 0.341 g/l/h was obtained at 96 h during the 2nd stage. This maximum productivity obtained from the continuous culture turned out only a small increase (3%) as compared to the corresponding batch fermentation. However, it should be noted that, in the case of batch process, one run typically consists of serial stages of growth culture plus one final production culture. This implies that, if the continuous fermentation that practically needs no dead time necessary for the multi-stage growth cultures is run for longer period, the total amount of the accumulated HA would be far greater than the amount obtained from the corresponding batch culture performed for the identical period.