• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.6
• /
• pp.390-396
• /
• 2021

Lithium-ion batteries have been designed and used as battery packs with series and parallel combinations that are suitable for use. However, due to its internal electrochemical properties, producing the battery's condition at the same value is impossible for individual cells. In addition, the management of characteristic deviations between individual cells is essential for the safe and efficient use of batteries as aging progresses with the use of batteries. In this work, we propose a method to manage deviation properties and detect abnormal behavior in the configuration of a combined battery pack of these multiple battery cells. The proposed method can separate and detect probabilistic low-frequency information according to statistical information based on Z-score. The verification of the proposed algorithm was validated using experimental results from 10S3P battery packs, and the implemented algorithm based on Z-score was validated as a way to effectively manage multiple individual cell information.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.6
• /
• pp.1291-1298
• /
• 2023

Surveillance reconnaissance sensor network is used for surveillance in wartime and area of operation. In this paper, we propose a target localization method using the detection signal strength of seismic sensors. Relay equipment calculates the target location using coordinate information and detection signal strength of the seismic sensors. Target localization error deviation due to environmental factors was minimized by subtracting the dynamic offset when calculating the target location. Field test shows improvement of target localization through reduction of errors. The average error was decreased to 3.62m. Up to 62% improved result was obtained compared to weighted centroid localization method.

• International Journal of Computer Science & Network Security
• /
• v.24 no.3
• /
• pp.182-188
• /
• 2024

Hardware components are an integral part of Hardware Define Radio (HDR) for seamless operations and optimal performance. On the other hand, Software Define Radio (SDR) is a program that does not rely on any hardware components for its performance. Both of the latter radio programmers utilize modulation functions to make their core components from signal processing viewpoint. The following paper concentrates on SDR based modulation and their performance under different modulations. The bit error rate (BER) of modulations such as PSK, QAM, and PSAM were used as indicators to test channel quality estimation in planar Rayleigh fading. Though it is not commonly used for channel fading, the method of the adder determines the regionally segmented channel fading. Thus, the estimation error of the channel change substantially reduces the performance of the signal, hence, proving to be an effective option. Moreover, this paper also elaborates that BER is calculated as a function of the sample size (signal length) with an average of 20 decibels. Consequently, the size of the results for different modulation schemes has been explored. The analytical results through derivations have been verified through computer simulation. The results focused on parameters of amplitude estimation error for 1dB reduction in the average signal-to-noise ratio, while the combined amplitude deviation estimation error results are obtained for a 3.5 dB reduction

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2698-2703
• /
• 2024

A bilateral comparison was conducted between the International Atomic Energy Agency (IAEA) and the Korea Research Institute of Standards and Science (KRISS) to measure the absorbed dose to water in accelerator photon beams. KRISS served as a linking laboratory to compare the IAEA standard with the key comparison reference value (KCRV) of the BIPM.RI(I)-K6 program, in which KRISS participated in 2017. Two ionization chambers from the IAEA were used as transfer instruments for the comparison. Both laboratories measured the calibration coefficients of these instruments and calculated the ratios. The ratio of the KRISS standard to the KCRV was applied to obtain the degree of equivalence of the IAEA, along with its uncertainty. The largest deviation of the IAEA measurement from the KCRV was 3.4 mGy/Gy, significantly smaller than the expanded uncertainty of 10.7 mGy/Gy (k = 2, 95% level of confidence). This study demonstrates the equivalence of IAEA's measurement standard for accelerator photon beams to other primary standard dosimetry laboratories. It provides evidence for the satisfactory operation of IAEA's quality management system and enhances the international credibility of the IAEA SSDL network, particularly in high-energy accelerator photon beams from linear accelerators.

• Archives of Plastic Surgery
• /
• v.35 no.5
• /
• pp.589-596
• /
• 2008

Purpose: The nasal bone fracture is most common fracture in facial bone injuries. Regardless of the severity or type of fracture, closed reduction has traditionally been the common method of treatment. However, through detailed pre-operative evaluation, we found out that many patients consider rhinoplasty prior to trauma due to aesthetic desire or nasal deformity with or without septal deviation. In treatment of nasal bone fracture, we focused not only on the fracture management but also on the patients' desire prior to trauma, and we made additional operation according to patients' desire with fracture reduction and gained rewarding outcomes. Methods: From March 2005 to June 2007, total 263 patients were treated for nasal bone fracture. Among these patients, 57 patients (21%) had the additional operation with nasal fracture reduction. The additional operations were categorized in three types: augmentation rhinoplasty with tip plasty (40%), septoplasty only (16%), corrective rhinoplasty (44%). The mean follow-up period was 5.6 months and results were evaluated by scoring. Results: Forty four of 57 patients (77%) were highly satisfied regardless of any additional operation kinds. The complications were one septal perforation, two displacement of implant and four remnant nasal deformities. For the septal perforation, no further management was performed because we lost the contact with the patient. Then 4 of the other complicated patients were revised. Conclusion: In general, many physicians tend to consider nasal fracture as a simple trauma. However through the strict history taking, physical examination and professional counseling, we could catch the patient's cosmetic desire and get the eyes on new concept: the nasal fracture is not only a trauma but a cosmetic and functional field. In the treatment of nasal bone fracture, if additional rhinoplasty is performed, patients will be more satisfied and we also can expect higher profits.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.12
• /
• pp.23-31
• /
• 2011

The simple bacteria cooperative optimization (sBCO) algorithm that we developed as one of optimization algorithms has shown relatively good performances, but their performances were limited by step-by-step movement of individuals at a time. In order to solve this problem, we proposed a new method that assigned a speed to each individual according to its rank and it was confirmed that it improved the performances of sBCO in some degree. In addition to the assigning of speed to the individuals, we employed a new mutation operation that most existing evolutionary algorithms used in order to enhance the performances of sBCO in this paper. A specific percent of bad individuals are mutated within an area that is proportion to the rank of the individual in the mutation operation. That is, Gaussian noise of large standard deviation is added as the fitness of individuals is low. From this, the probability that the individuals with lower ranks can be located far from its parent will be increased. This causes that the probability of falling into local optimum areas is decreased and the probability of fast escaping the local optimum areas is increased. From experimental results with four function optimization problems, we showed that the performances of sBCO with mutation operation and individual speed were increased. If the optimization function is quite complex, however, the performances are not always better. We should devise a new method for solving this problem as a further work.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.25 no.2
• /
• pp.91-100
• /
• 2017

The purpose of this study is to provide a design and operation technical guideline for meeting the appropriate design criteria to bio-gasification facilities treating organic wastes. In accordance with the government's mid-to long-term policies on bio-gasification and energization of organic wastes, the expansion of the waste-to-energy (WTE) facilities is being remarkably promoted. However, because of the limitation of livestock manure containing low-concentration of volatile solids, there has been increased in combined bio-gasification without installing new anaerobic digestion facilities. The characteristics and common problems of each treatment processes were investigated for on-going 13 bio-gasification facilities. The seasonal precision monitoring of chemicophysics analysis on anaerobic digestor samples was conducted to provide guidelines for design and operation according to the progress of bio-gasification treatment. Consequently, major problems were investigated such as large deviation of organic materials depending on seasons, proper dehumidification of biogas and pretreatment of hydrogen sulfide.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.1
• /
• pp.107-114
• /
• 1996

The in situ target strength for the anchovy (Engraulis japonica) were measured by the split beam echo sounder system at 38 kHz. This study allowed us to detect the single echos from anchovy shoals which were dispersed during trawling operation in day time. The results of our study were as fellows: We found that the anchouy occupied about $95\%$ of the total catch from the detected shoals from which target strength data were collected. Length distribution of anchovy showed a mode and ranged from 13.6 to 15.4cm with a mean of 14.4cm and a standard deviation of 0.45cm, and weight distribution showed a mode and ranged from 16 to 28 g witha mean of 21.9 g and a standard deviation of 2.7 g. The target strength distribution of anchovy ranged from -40.7 dB to -69.2 dB in the water layer of ,$10\~30\;m$ -42.19 to -67.7 dB in the $30\~50\;m$ and -42.2 to -67.7 dB in $10\~50\;m$, showing 2 modes in each layer, respectively. Overall mean target strengths were -49.7 dB/fish and -33.1 dB/kg, averaged by area backscattering cross section $(\sigma)$, and the confidence interval for target strength was less than 1 dB. With the mean total length and the mean target strength, we drived the target strength-length relationship as $TS(\sigma)=20\;Log\;L-72.9$.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.3
• /
• pp.304-311
• /
• 2014

In this study, to apply hydrogen energy to ship engine and to generate effective hydrogen production, we investigated the effects of high temperature $H_2SO_4$ feed rate and cooling water rate to pump parts with fixed frequency needed to reciprocate motion and a simulation was conducted at each condition. In the fixed frequency and cooling water inlet flow rate of 0.5 Hz and 3.9 kg/s, we changed the high temperature $H_2SO_4$ flow rate to 47.46 kg/s (it is 105 % of 45.2 kg/s), 49.72 kg/s (110 %), and 51.98 kg/s (115 %). Also, at 0.5 Hz and 45.2 kg/s of frequency and high temperature $H_2SO_4$ flow, the thermal hydraulic analysis was performed at the condition of 95 % (3.705 kg/s), 90 % (3.51 kg/s), and 85 % (3.315 kg/s). In overall simulation cases, the physical properties of materials are more influential to the temperature increase in the pump part rather than the changes on the feed rate of high temperature $H_2SO_4$ and cooling water. A continuous operation of pump was also capable even if the excess feed of high temperature $H_2SO_4$ of about 15 % or the less feed of cooling water of about 15 % were performed, respectively. When the increasing feed of high temperature $H_2SO_4$ of up to 5 %, 10 %, and 15 % were compared with base flow (45.2 kg/s), the deviation of time period rose to a certain temperature and ranged from 0 to 4.5 s in the same position (same material). In case of cooling water, the deviation of time period rose to a certain temperature and ranged from 0 to 5.9 s according to the decreasing feed changes of cooling water at 5 %, 10 %, and 15 % compared to a base flow (3.9 kg/s). Finally, the additional researches related to the two different materials (Teflon and STS for Pitch and End-plate), which are concerned about the effects of temperature changes to the parts contacting different materials, are needed, and we have a plan to conduct a follow-up study.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.3
• /
• pp.31-40
• /
• 2012

The irregularity of railway track affects not only the comfort of ride such as noise or vibration but also the safety of train operation. For this reason, it is an interesting research area to design a reliable and sustainable railway track system and to analyze the train movement mechanism based on systematic approaches considering reasons of track irregularity possible in a specific local environment. Irregularity data inspected by EM-120, an railway inspection system in Korea includes unavoidable incomplete and erratic information, so it is encountered lots of problem to analyse those data without appropriate pre-data-refining processes. In this research, for the efficient management and maintenance of railway system, progress rate of standard deviation of irregularity is quantified. During the computation, some important components of railways such as rail joint, ballast, roadbed, and fastener have been considered. Probabilistic distributions of irregularity growth with respect to time are computed to predict the remaining service life of railway track and to be adapted for the safety assessment.