• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.387-392
• /
• 2003

This study is put a focus on the identification of sound characteristics according to the interior configuration of sound absorption material and air gap. Noise barrier is general consists of front perforated panel, air layer, sound absorption material, air gap and back plate. Noise barrier is required to the NRC value of 0.7. The absorbing performance of the noise barrier relies on the opening ratio of the perforated panel and the efficiency of the absorbing material. This study has observed the effect of opening ratio and hole size, the increase of sound absorbing performance by the configurations of sound absorption material and air gap. New designed noise barrier is achieved the acoustical performance of 0.87 the measurement in a reveration room.

• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.1-8
• /
• 2018

In this study, the effects of variation in cam phasing and valve lift of exhaust valves by using Cam-in-Cam system on combustion and emission characteristics for diesel engine were investigated under GT-POWER simulation environment. This paper showed analytic result of combustion characteristics and diesel exhaust valve's control with GT-Power 1-D detail model. As a result, it was found that volumetric efficiency and IMEP were decreased as the exhaust valve opening and closing timing is advanced due to its internal EGR effects. Also, it was found that NOx emission were decreased as EVC timing was retarded. These show that the retarding the exhaust valve closing and opening while keeping the duration at constant can be effective for controlling AFR and mixing rate in diffusion combustion of diesel engine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.1
• /
• pp.9-16
• /
• 2005

This study was conducted in order to improvement of fishing gear and fishing operating system for anchovy boat seine by labor saving improved nets. Field experiments were carried out observe geometry of nets and fishing operating system by catcher boats. The obtained results are summarized as follows : The Vertical net opening of fore wing net, wing net, inside wing net, square, fore bag net, flapper, after bag net of the labor saving improved net according to the distance between catcher boats were varied in the range of 5.0${\sim}$7.8, 14.4${\sim}$21.1, 16.2${\sim}$21.2, 14.0${\sim}$17.3, 11.7${\sim}$13.9, 5.4${\sim}$6.9, 8.2${\sim}$9.8m respectively, varied in the range of 50${\sim}$78, 25${\sim}$36, 24${\sim}$31, 31${\sim}$38, 61${\sim}$73, 71${\sim}$91, 87${\sim}$104% of the actual ratio of net opening in each part. Labor saving improved net was performed instant net opening in fore wing net and maintained stable net opening and towing depth by means of attached net pendant. Also, it was minimized as net pocket phenomenon leading to guide anchovy for more catch by means of attached body net. The opening in accordance with distance between catcher boats and towing speed. The catch of labor saving improved net was increased than traditional net due to decrement of net resistance by improvement of bag net leading to increasement of towing speed and reduction of escape anchovy as well as improve nets of whole operation system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.1
• /
• pp.15-22
• /
• 2014

Multiple devices have been installed to reduce exhaust emissions and to increase thermal efficiency. Those devices reduce the exhaust pipe opening area and increase the exhaust gas pressure. The pressure increase disturbs a gas flow and has a bad effect on the engine performance. However there is some study that NOx can be reduced with exhaust gas pressure increase. In this study an engine performance is tested with various opening ratios. The result shows that the fuel consumption rate is reduced in case of little amount of the pressure increase, and NOx is reduced with the pressure increase, while the concentration of the toxic exhaust gases are increased in the case of high back-pressure.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.4
• /
• pp.217-224
• /
• 2020

In this study, a framework for optimizing the opening in an outrigger wall is proposed. To solve a constrained bounded optimization problem, an in-house finite element program and SQP algorithm in Python SciPy library are utilized. The openings of the outrigger wall are located according to the strut-tie behavior of the outrigger wall deep beam. A linear interpolation method is used to obtain differentiable continuous functions required for optimization, whereas a database is used for the efficiency of the optimization program. By comparing the result of the two-variable optimization through the moving path of the search algorithm, it is confirmed that the algorithm efficiently determines the optimized result. When the size of each opening is set to individual variables rather than the same width of all openings, the value of the objective function is minimized to obtain better optimization results. It was confirmed that the optimization time can be effectively reduced when using the database in the optimization process.

• Journal of radiological science and technology
• /
• v.42 no.6
• /
• pp.477-482
• /
• 2019

Recently, due to the increased use of medical radiation, the radiation exposure of radiation workers should be considered as well as medical exposure of patients. And it is recommended to close the door during radiography. however, In this study, when the door was inevitably opened for radiography, the proposed method was to install the shield as a method of reducing the exposure dose. And its efficiency was analyzed. In simple chest radiography, the measurement point was changed according to the measurement location. Dose rate were measured 10 times for each condition using a dosimeter. And the average value was derived. Using this, the change of dose according to the opening and closing of the door and the installation of the shield was analyzed. Using this, we compared and analyzed the dose change according to the door opening and closing and the installation of the shield, and significance was verified through the SPSS ver. 24. Depending on whether the door was opened or closed, 11,215.35%, 159.0%, 101.9% increased in front of the door in the consol room, behind the wall and behind the lead glass. Depending on the installing of the shield, the 49.2%, 29.6%, 19.9%, 30.6% decrease in front of the door in the examination and consol room, behind the wall and lead glass. In addition, statistical analysis was showed that there were significant differences in both the results according to whether the door was opened or closed and shielding(p<.05). Close the door during radiography. However, when the door should be opened, it was confirmed that the dose rate were reduced by installing the shield. Therefore, to optimize radiation protection, it is recommended to install shields when opening the door.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_3
• /
• pp.1183-1190
• /
• 2022

Recently, the Ministry of Strategy and Finance announced a plan to reduce the proportion of economic evaluation in non-metropolitan areas and strengthen balanced development evaluation through the reorganization of the preliminary feasibility study system. In addition, the social value of the quality of life, such as job, environment, and safety, which may be affected by the implementation of transportation facility investment projects, was reflected as the main item of policy evaluation. In this study, the ripple effect of the project in terms of social value was reviewed for the Gangil-Chuncheon. The effect of highway opening was investigated by reviewing the feasibility report, post-evaluation report, and statistical indicators. Recently, the Gangil-Chuncheon highway is getting used by around 110,000 people per day. The number of tourists in Chuncheon rapidly has increased from 5 million a year to more than 11 million now. In addition, it was confirmed to produce effects such as population migration, net inflow and land price increase, improvement of living convenience, and expansion of emergency medical care. Although this ripple effect was influenced by various socio-economic factors as well as the opening of the highway, it is clear that it is difficult to occur without the opening of the highway. It is judged that the evaluation of indirect benefits and social values due to the opening of the highway can be quantified through continuous research and data construction. Post-evaluation of construction works, including project efficiency evaluation and ripple effect evaluation, is performed for construction works with a construction cost of more than 50 billion won. In the future, we will continuously improve the evaluation system in order to evaluate the indirect benefits and social values of public investment projects.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.41 no.2
• /
• pp.140-149
• /
• 2008

This study evaluated the efficiency of an oil fence and spreading devices for one vessel in a towing tank. A series of model experiments and numerical calculations were conducted using an existing oil fence for two vessels and a new method for one vessel. Models of the oil fence and spreading devices were constructed on $1/20^{th}$ scale from waterproofed nylon fabric and canvas. The tensions acting on the model of the oil fences and the horizontal distance between the spreading devices were calculated numerically while the oil fences were being towed. The results were extremely close to the results of the model experiments. The ratio of the opening width to the total length of the oil fence, which shows the efficiency of the oil fence for one vessel, was 49.7% in 0.4 m/sec. Therefore, the proposed oil fence system should be very useful for oil containment at sea. As the opening width of the oil fence is not proportional to the length of the towing rope, it may be reasonable to maintain the towing rope at approximately 100 m. Furthermore, a reasonable towing speed, when operating the oil fence for one vessel equipped with spreading devices, was within 0.4 m/sec.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.3
• /
• pp.25-32
• /
• 2014

The main objective of this study is to validate the performance characteristics of newly developed micro propeller turbine based on experimental model test. For this purpose, Measurements of efficiency and cavitation tests with variations on the guide vane opening, blade rotational speed, head and load are carried out according to the IEC standard for model testing. From the tests and scale up calculation, the maximum prototype and model efficiency of the runner blade reaches as high as 90.87 % and 90.27 % respectively. Test results show that good cavitation behavior is covered in the range of output 50kW and 100 kW.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.876-882
• /
• 2009

With overall opening of global construction market by World Trade Organization (WTO) agreements, importance of management efficiency of construction industry which considers both tangible and intangible assets is recently being recognized in our nation. That is, efforts for reinforcement of competitiveness must be placed through maximization of values of internal and external intangible assets of construction industry such as management innovation, information, investment in technology and R&D and intellectual property. Accordingly in this study, evaluation criteria for intangible assets of construction industry were investigated and classified. Using such criteria, evaluation index and model were established based on the degree of importance of each criterion. The purpose of this study is to review importance of intangible assets in terms of competitiveness and management efficiency of construction industry and to provide basic data for establishment of intangible assets and revitalization of investment.