• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.855-860
• /
• 2023

Long-haul transmission of multiple transmission signals, such as wavelength division multiplexed (WDM), has became possible, because the signal distortion caused by chromatic dispersion and nonlinearity can be compensated by applying dispersion management, optical phase conjugation and combination of the two methods into the transmission link. The biggest obstacle to applying optical phase conjugation to an optical link is that the optical phase conjugator (OPC) must be located only in the middle of the entire transmission line. This paper shows that the location constraints of OPC can be overcome through the application of an asymmetric dispersion map. The location of the OPC considered in this paper exists between the 8th and 9th fiber spans out of a total of 48 fiber spans. Additionally, the dispersion map has an asymmetric cumulative dispersion profile with respect to the OPC. As a result of the simulation, it was confirmed that the distortion compensation effect of the WDM channel can be increased compared to the link to which the traditional dispersion map is applied, depending on the overall shape of the cumulative dispersion profile distribution of the proposed asymmetric dispersion map and the selection of the profile slope.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.931-932
• /
• 2008

• Journal of information and communication convergence engineering
• /
• v.5 no.3
• /
• pp.273-280
• /
• 2007

The numerical methods for finding the optimal parameters in 640 Gbps (16 channels $\times$ 40 Gbps) WDM system with optical phase conjugator (OPC) are proposed, which effectively compensate the distorted overall WDM channels. The considered optimal parameters are the OPC position and the dispersion coefficient of fibers. The numerical approaches are accomplished through two different procedures. One of these procedures is that the optimal OPC position is previously searched and then the optimal dispersion coefficient is searched at the obtained optimal OPC position. The other is the reverse of the above procedure. From the numerical results, it is confirmed that two optimal parameters depend on each other, but less related with the searching procedure. The methods proposed in this research will be expected to alternate with the method of making a symmetrical distribution of power and local dispersion in real optical link which is a serious problem of applying the OPC into multi-channels WDM system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.901-907
• /
• 2000

As the minimum feature size for making ULSI approaches the wavelength of light source in optical lithography, the aerial image is so hardly distorted because of the optical proximity effect that the accurate mask image reconstruction on wafer surface is almost impossible. We applied the Optical Proximity Correction(OPC) on isolated patterns assuming Attenuated Phase Shift Mask(APSM) as well as binary mask, to correct the widening of isolated patterns. In this study, we found that applying OPC to APSM shows much better improvement not only in enhancing the resolution and fidelity of t도 images but also in enhancing the process margin than applying OPC to the binary mask. Also, we propose the OPC method of APSM for isolated patterns, the size of which is less than the wavelength of the ArF excimer laser. Finally, we predicted the resolution limit of optical lithography through the aerial image simulation.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.224-229
• /
• 2018

OPC production requires high calorific value and emits a large amount of $CO_2$ through decarbonation of limestone, accounting for about 7% of $CO_2$ emissions. To reduce $CO_2$ emissions during the Ordinary Portland Cement (OPC) production process, there is a method of reducing the consumption of cement or lower temperature calcination for OPC product. In this study, for energy consumption reduction, we prepared Hauyne-belite cement by calcination at a low temperature compared to that used for OPC and studied the early hydration properties of the synthesized Hauyne-belite cement. We set the ratios of Hauyne and belite to 8 : 2, 5 : 5 and 3 : 7. For the hydration properties of the synthesized Hauyne-belite cement, we tested heat of hydration of paste and the compressive strength of mortar, using XRD and SEM for analysis of hydrates. As for our results, the temperature for optimum synthesis of Hauyne-belite is $1,250^{\circ}C$. Compressive strength of synthesized Hauyne-belite cement is lower than that of OPC, but it is confirmed that compressive strength of synthesized Hauyne-belite cement with mixing in of some other materials can be similar to that of OPC.

• The Korean Journal of Ceramics
• /
• v.3 no.2
• /
• pp.88-91
• /
• 1997

The diamondlike (DLC) films were deposited by RF plasma CVD system which had cathode consisting of mesh sheet, for the purpose of a protection from wear of OPC surface of the electrophotographic photosensitive body. Material charateristics and tribological properties of the films were also investigated and finally copying performance was evaluated with DLC deposited OPC samples. The surface resistance of the DLC film unaffected by the surface potential of the OPC was about $10^{11}{\Omega}$ and its hardness was about 1200 kg/$\textrm{mm}^2$. In this case the film showed typical material strcture of dimondlike hydrocarbon. The friction coefficient of the film was lowered to 0.2~0.3 at the optimum condition in this investigation and their wear resistant was inproved by DLC-deposition on the OPC surface. DLC-deposited OPC samples with a good copying performance without image flow and draft could be obtained at some depositing conditions.

• Tribology and Lubricants
• /
• v.23 no.3
• /
• pp.103-108
• /
• 2007

In this paper, the optimized design and strength analysis have been presented based on the finite element and Taguchi's experimental methods. The stress, strain and displacement characteristics of OPC drum tubes are affected by rolling contact pressures between an OPC drum tube and a paper, design parameters of an aluminum tube and material properties. The OPC drum tubes with nine different geometrical models are analyzed for design parameters that are related to the outer diameter, the thickness, and the length of an aluminum tube for a toner cartridge. The optimized design parameters for an aluminum tube may be selected as the outer diameter of 28 mm, the thickness of 0.8 mm, and the length of 220 mm. But the currently used aluminum tube for a laser printer is fairly optimized based on the Taguchi's design analysis. The calculated FEM results showed that the affection ratio of the design parameter t, which may control the strength of an aluminum tube, is the most influential parameter among the length and an outer diameter of a tube.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.5
• /
• pp.515-528
• /
• 2003

The characteristics of one year observation aerosol data in Seoul, 200 I was studied using an OPC (Optical Particle Counter). The size resolved aerosol number concentrations of 0.3 ∼ 25 11m were measured. The results were compared with PM$_{10}$ mass concentration data under various meteorological conditions including dust and precipitation events. For fine particles whose diameter is less than 2.23 ${\mu}{\textrm}{m}$, the number concentration increases in the early morning which is considered due to transportation. while the coarse mode particles increase during daytime. This increase can be explained as local sources and human activities near sampling site. Hourly averaged data show that there exists diurnal variation. Generally, PM$_{10}$ data showed a similar tendency with OPC data. The size resolved OPC data showed that the particles of 0.5 ∼ 3.67 ${\mu}{\textrm}{m}$ are positively correlated with PM$_{10}$ data. The accumulated volume fraction of size resolved aerosol concentration in 0.5 ∼ 10 ${\mu}{\textrm}{m}$ showed that 0.5 ∼ 2.23 ${\mu}{\textrm}{m}$ particles occupied 59.2% of total aerosol volume of 0.5 ∼ 10 ${\mu}{\textrm}{m}$./TEX>.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.905-908
• /
• 2008

The existing concrete using ordinary portland cement has difficult in earth strength. so our study proceeded in using the micro cement. the result of experiment is follow that strength of micro cement was hard better than ordinary portland cement in early strength but flow of ordinary portland cement was better than micro cement. when OPC and MC mixed by fly-ash, flow degree is increased because of ball baring. fly-ash type wicked in early strength but flyash type hard than 28days strength of OPC. flow of GBFS is decreased, early strength is increased. when fly-ash mixed in MC, it was wicked strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.87-91
• /
• 2009

This study investigates possibility for practical use through small sized test with OPC and substituted fly ash 10% and return coarse cement (RCC), classed 1100${\sim}$1200 cm2/g, which is made by Cyclone Separator at cement producing process 20% (CF) for OPC. The experimental factors are 48% of W/B and OPC and 2 kinds of concrete proportions. The target slump and air content are $150{\pm}25$ mm and $4.5{\pm}1.5$ %. For the results, the flowalility and air content of CF are less than OPC because it needs more superplasticiser and air-entraining agent. The temperature history of CF is lower than OPC about $6{\sim}10^{\circ}C$. For the strength properties, CF is less than OPC, but their gap is declined at 28 days. The strength of the specimens are ordered by standard curing, field cured specimens, and core specimens.