• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.5
• /
• pp.625-633
• /
• 2021

This paper considers the development of safety operation guideline for onboard A-Frame system used to operate heavy-work ROV using dynamic simulation. Onboard A-Frame is affected by ship's behavior and large inertia by the marine environment. For this reason, safety operation guidelines are required for the safety of workers who operate ship-mounted equipment. In order to develop a guideline, it is necessary to evaluate the safety loads through real sea experiment. However, simulation method is used instead since it is difficult to conduct experiments in sea. Therefore, a procedure for safety operation analysis based on dynamic simulation that can consider ship behavior and marine environment and a safety operation table were proposed in this study. And the construction of safety operation table and guide for safety operation using the applied load and safety factor analysis results were considered.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.141-144
• /
• 2006

The deviations in the injection orbital parameters, resulting from launcher dispersions, need to be estimated and used for autonomous satellite operations. For the proposed small satellite mission of the university there will be two GPS receivers onboard the satellite to provide the instantaneous orbital state to the onboard data handling system. In order to meet the power requirements, the satellite will be sun-tracking whenever there is no imaging operation. For imaging activities, the satellite will be maneuvered to nadir-pointing mode. Due to such different modes of orientation the geometry for the GPS receivers will not be favorable at all times and there will be instances of poor geometry resulting in no output from the GPS receivers. Onboard the satellite, the orbital information should be continuously available for autonomous switching on/off of various subsystems. The paper presents the strategies to make use of small arcs of data from GPS receivers to compute the mean orbital parameters and use the updated orbital parameters to calculate the position and velocity whenever the same is not available from GPS receiver. Thus the navigation message from the GPS receiver, namely the position vector in Earth-Centered-Earth-Fixed (ECEF) frame, is used as measurements. As for estimation, two techniques - (1) batch least squares method, and (2) Kalman Filter method are used for orbit estimation (in real time). The performance of the onboard orbit estimation has been assessed based on hardware based multi-channel GPS Signal simulator. The results indicate good converge even with short arcs of data as the GPS navigation data are generally very accurate and the data rate is also fast (typically 1Hz).

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.42 no.1
• /
• pp.1-10
• /
• 2006

Present study was conducted to improve the spring frame net trap for conger eel, Conger myriaster which prevents by-catch and protects immature fish. A series of comparative fishing experiment was carried out in water off the south-east coast of Korea from Nov. 2004 to Jul. 2005. And analyzed the amount of catch, by-catch rate, and CPUE, etc. of experimental traps which were the spring frame net traps, sorted four types of flappers. And the compared gear was a plastic conger eel pot. The conclusions were as follows. By-catch rates of spring frame net trap with the compressed flapper bound by nylon mono-filament was about 0-3%. CPUE of spring frame net trap with the compressed flapper was about 50-60% lower than that of traditional and plastic pot. And in case of conger eel that the total length is over 350mm, CPUE was little different on each type of flapper of every mesh size.

• Journal of The Korean Astronomical Society
• /
• v.56 no.2
• /
• pp.293-299
• /
• 2023

The Wide-Angle Polarimetric Camera (PolCam) is installed on the Korea's lunar orbiter, Danuri, which launched on August 5, 2022. The mission objectives of PolCam are to construct photometric maps at a wavelength of 336 nm and polarization maps at 461 and 748 nm, with a phase angle range of 0°-135° and a spatial resolution of less than 100 m. PolCam is an imager using the push-broom method and has two cameras, Cam 1 and Cam 2, with a viewing angle of 45° to the right and left of the spacecraft's direction of orbit. We conducted performance tests in a laboratory setting before installing PolCam's flight model on the spacecraft. We analyzed the CCD's dark current, flat-field frame, spot size, and light flux. The dark current was obtained during thermal / vacuum test with various temperatures and the flat-field frame data was also obtained with an integrating sphere and tungsten light bulb. We describe the calibration method and results in this study.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.15-23
• /
• 2007

In surveillance, monitoring, and target tracking operations, high-resolution images should be obtained even if the target is in a far distance. Frequent movements of vehicles such as boats degrade the image quality of onboard camera systems. Therefore, stabilizer mechanisms are required to stabilize the line of sight of boatboard camera systems against boat movements. This paper addresses design and implementation of a strapdown boatboard camera stabilizer. A two degree of freedom(DOF)(pan/tilt) robot performs the stabilization task. The main problem is divided into two subproblems dealing with attitude estimation and attitude control. It is assumed that exact estimate of the boat movement is available from an attitude estimation system. Estimates obtained in this way are carefully transformed to robot coordinate frame to provide desired trajectories, which should be tracked by the robot to compensate for the boat movements. Such a practical robotic system includes actuators with fast dynamics(electrical dynamics) and has more degrees of freedom than control inputs. Backstepping method is employed to deal with this problem by extending the control effectiveness.

• Journal of Astronomy and Space Sciences
• /
• v.38 no.3
• /
• pp.157-164
• /
• 2021

We describe a method for the in-orbit calibration of body-mounted magnetometers based on the CHAOS-7 geomagnetic field model. The code is designed to find the true calibration parameters autonomously by using only the onboard magnetometer data and the corresponding CHAOS outputs. As the model output and satellite data have different coordinate systems, they are first transformed to a Star Tracker Coordinate (STC). Then, non-linear optimization processes are run to minimize the differences between the CHAOS-7 model and satellite data in the STC. The process finally searches out a suite of calibration parameters that can maximize the model-data agreement. These parameters include the instrument gain, offset, axis orthogonality, and Euler rotation matrices between the magnetometer frame and the STC. To validate the performance of the Python code, we first produce pseudo satellite data by convoluting CHAOS-7 model outputs with a prescribed set of the 'true' calibration parameters. Then, we let the code autonomously undistort the pseudo satellite data through optimization processes, which ultimately track down the initially prescribed calibration parameters. The reconstructed parameters are in good agreement with the prescribed (true) ones, which demonstrates that the code can be used for actual instrument data calibration. This study is performed using Python 3.8.5, NumPy 1.19.2, SciPy 1.6, AstroPy 4.2, SpacePy 0.2.1, and ChaosmagPy 0.5 including the CHAOS-7.6 geomagnetic field model. This code will be utilized for processing NextSat-1 and Small scale magNetospheric and Ionospheric Plasma Experiment (SNIPE) data in the future.