• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.149-152
• /
• 2002

If the ambient temperature rises for AC PDP, some of the discharge cells are turned off because of the misfiring during address period. Particularly, the misfiring of the 'last scan line is more serious than that of the first. In order to compensate the misfiring in such that case, different addressing voltage is applied at each cell such as progressively increasing pulse voltage instead of constant one. As a result, the addressing time and discharge charge of the last scan line have become similar to those of the first scan line and the phenomenon of misfiring has disappeared.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.4
• /
• pp.183-190
• /
• 2007

In most hard disk drives that apply the ramp load/unload technology, the head is unloaded at the outer edge of the disk while the disk is rotating. During the unloading process, slider-disk contacts may occur by lift-off force and rebound of the slider. The main issue of this paper is to prevent the slider-disk contact by rebound, and we apply a disk bump to the unloading process. To do so, first, the ranges of bump dimension are determined. Second, the stability of each bump is checked by dynamic simulation. Finally, unload simulations are performed for stable bump designs. As a result of these steps, the effect of the bump design and the position for the unloading performance were investigated. As a consequence, we propose the optimal bump design to improve the unloading performance. Furthermore, we can identify to remove rebound contact by applying a bump on disk during the unloading process.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1265-1267
• /
• 1993

The switching and the retention characteristics with the injection conditions(pulse height and pulse width) were investigated in the nonvolatile MNOS memories with thin oxide layer of $23{\AA}$ thick. The shift of flatband voltage was measured using the fast ramp C-V method and experimental results were analized using the previously developed models. It was shown that the experimental results were described quit well by the trap-assisted and modified Fowler-Nordheim tunneling models for the voltage pulse of $15V{\sim}19V,\;24V{\sim}25V$, respectively. However, the direct tunneling model was agreement with experimental values in all range of pulse height. As increasing the initial shift of the flatband voltage, the decay rate was increased. But for the same initial shift of the flatband voltage, the decay rate was smaller for low and long pulse than for high and short one.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.1
• /
• pp.24-28
• /
• 2010

A simulation study of a current-mode direct current (DC)-DC buck converter is presented in this paper. The converter, with a fully integrated power module, is implemented by using sense method metal-oxide-semiconductor field-effect transistor (MOSFET) and bipolar complementary metal-oxide-semiconductor (BiCMOS) technology. When the MOSFET is used in a current sensor, the sensed inductor current with an internal ramp signal can be used for feedback control. In addition, the BiCMOS technology is applied in the converter for an accurate current sensing and a low power consumption. The DC-DC converter is designed using the standard $0.35\;{\mu}m$ CMOS process. An off-chip LC filter is designed with an inductance of 1 mH and a capacitance of 12.5 nF. The simulation results show that the error between the sensing signal and the inductor current can be controlled to be within 3%. The characteristics of the error amplification and output ripple are much improved, as compared to converters using conventional CMOS circuits.

• Journal of Drive and Control
• /
• v.10 no.4
• /
• pp.34-40
• /
• 2013

The transmission control method of small forklift is classified into pilot control method and direct control method. In pilot control method, the hydraulic circuit which consists a lot of components is very complex so the production process is too costly and time consuming. The direct control method contains fewer components that can be configured to simple hydraulic circuit. It has more advantages because the shift sensitivity of transmission is changed easily via the input profile. In this paper, the controller design and the input profile for system are studied to apply to the direct control method. The input profile consists of Fill section, Hold section and Ramp section. The characteristic of each section is obtained through experiment. As the result, the shift sensitivity and starting performance are effected by Fill section and Hold section.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.492-498
• /
• 2008

In this paper are described recent studies about variable nozzles, that are a rectangular type nozzle and an axisymmetric type nozzle, of the precooled turbojet engine(S-engine) which are developed for the demonstration of the key technologies for the propulsion system of the hypersonic airplane and the first stage propulsion of the TSTO space plane. For the rectangular nozzle, three types of C-shaped carbon/carbon composite cowls which includes subscale model of the precooled turbojet engine are fabricated and the fine attachment to the ramp is confirmed. For the firing of the S-engine, stainless steel cowl with concrete heat insulator are fabricated and tested for 20 sec. Axisymmetric variable plug nozzle which is made of C/C material is fabricated and pressurized by the cold flow test. The axisymmetric plug nozzle can be operative up to 0.57 MPa of nozzle inlet pressure.

• Ocean Systems Engineering
• /
• v.10 no.4
• /
• pp.359-371
• /
• 2020

The performance of a multi-level overtopping wave energy converter (OWEC) has been numerically and experimentally investigated in a two-dimensional wave tank in order to study the effects of opening width of additional reservoirs. The device is a fixed OWEC consisting of an inclined ramp together with several reservoirs at different levels. A particle-based numerical simulation utilizing the Lattice Boltzmann Method (LBM) is used to simulate the flow behavior around the OWEC. Additionally, an experimental model is also built and tested in a small wave flume in order to validate the numerical results. A comparison in energy captured performance between single-level and multi-level devices has been proposed using the hydraulic efficiency. The enhancement of power capture performance is accomplished by increasing an overtopping flow rate captured by the extra reservoirs. However, a noticeably large opening of the extra reservoirs can result in a reduction in the power efficiency. The overtopping flow behavior into the reservoirs is also presented and discussed. Moreover, the results of hydrodynamic performance are compared with a similar study, of which a similar tendency is achieved. Nevertheless, the LBM simulations consume less computational time in both pre-processing and calculating phases.

• Journal of Korean Port Research
• /
• v.13 no.1
• /
• pp.113-122
• /
• 1999

Congestion and traffic accidents occur on the merge and diverge sections in the interchange of the freeway. Studies have been conducted to reduce the traffic delay and accidents on the merge section in the freeway since 1960s. but a study was not conducted to estimate the speed variation on the merge section construct models estimated for the speed variation and suggest the appropriate measures. The purpose of this study was to identify the traffic flow characteristics on the merge section in the freeway construct the models estimated for the speed variation on the merge section in the freeway and finally establish the appropriate measure for reduction of traffic delay and accidents on the merge section in the freeway. The following results were obtained: I) Speed variations in the urban freeway appeared to be about 3.2mph, 6.5mph and 7.4mph based on the morning peak period, afternoon peak period and 24-hours period but those in the suburban freeway appeared to be about 8.0mph, 11.1mph and 10.1mph based on the same periods respectively. So different speed reduction signs need be installed to reduce delay and accidents on the merge section in the freeway based on the areas and periods as the freeway traffic management system(FTMS). ii) These models estimated for speed variation need to be studied with the changeable message sign(CMS) technique based on the real-time data so that the traffic flow could be maximized and the traffic delay and accidents be on the merge section in the freeway as more efficient freeway traffic management system(FTMS) in the near future.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.6
• /
• pp.162-172
• /
• 2009

Improvement of roadway environments to accommodate elderly drivers' declining driving capabilities are required. Currently, even the types of roadway designs vulnerable to elderly drivers have not been revealed in Korea. Thus, this study aims to analyze the types and vulnerabilities of the roadway designs that elderly drivers experience more accidents based on crash data of the Korean National Police Agency. This study has also reviewed foreign guidelines enhancing their safety on different roadway designs. Compared with normal drivers, elderly drivers tend to be more frequently involved in traffic accidents on intersections and vehicle-to-vehicle accidents on curved roadway segments. Assuming freeway interchanges are also risky sections, this study has also examined several methods to reduce elderly driver-related accidents on freeway ramp areas.

• International Journal of Highway Engineering
• /
• v.7 no.4 s.26
• /
• pp.173-184
• /
• 2005

Pavement markings delineate driver's sight and attentions at day and night. Retroreflectivities of the pavement markings are known to be affected by some factors such as geometrical characteristics of road sections, marking materials, traffic volumes, weather, and so on. Therefore, pavement markings would have different retroreflectivities place by place. The objective of this paper is to contend that there are rises and falls of retroreflectivity of specific geometrical characteristics of road section based on observed field data. For this purpose, retroreflectivities of yellow continued lines and white skip lines were measured on the freeway sections from Hanam to Nami interchanges. And then, the sections are categorized based on road geometric or facility types. From this study, it may be concluded that there exist considerably lower retroreflectivity trends of pavement markings at sharply curved sections, climbing lane sections, ramp sections, and tunnel sections than averaged retroreflectivity trends on freeway sections. This may leads to the necessity of differential pavement marking managements.