• Textile Coloration and Finishing
• /
• v.11 no.5
• /
• pp.44-54
• /
• 1999

Poly(ethylene 2,6-naphthalate), PEN, is a relatively well-known polymer used for engineering purposes. Naphthalene ring provides rigidity to the polymer backbone, thus, it elevated the glass transition temperature and enhanced mechanical properties. The structure and properties of PEN affect a processing conditions severely, and the high-thermal stability have been had a poor thermal processibility. Hence, the basic mechanism of solvent drawing, is very much the same as that of thermal drawing from glassy state since both involve the inducement of segmental mobility. The former achieves the goal by use of chemical energy, and the latter does so by use of thermal energy. Generally, the sorption of the solvent by the polymer has a plasticizing effect, and leads to a lowering of the glass transition temperature, $T_g$. In this paper, the dynamic viscoelasticity behavior in liquid-drawing process of an unoriented amorphous PEN films were investigated using Rheovibron. The results are as follows ： (1) For the drawing in silicone oil, the drawing below $T_g$. had $\alpha{2}$-dispersion due to an inhomogeneous taut structure. (2) For the drawing in water, the inhomogeneous taut structure reduced by the effect of plasticization even below $T_g$. (3) For the drawing in butanol, the only aliphatic segment in PEN have some molecular mobility but the mobility of the aromatic segment having naphthalene ring is nearly impossible. (4) For the drawing in dioxane/water mixing solvent, the solvent effect is complementary each other and accordingly the entire molecular conformation have stable state. (5) For the drawing in dioxane/butanol mixing solvent, the inhomogeneity of the taut structure and the aromatic segment increase with increasing the temperature and this tendencies correspond with that of the draw ratio.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.10 no.3
• /
• pp.27-36
• /
• 1986

The purpose of this study was, to estimate the detergency of commercial detergent and to examine the interrelationship between detergency and detergent characteristics, detergent concentration, fiber characteristics, and Rolling-up phenomenon which is the major removal mechanism of oily soil. A mixture of oleic acid-olive oil was used as oily soil. The detergency was estimated by analysis of oleic acid on cotton ana polyester fabrics before and after washing by means of liquid scintillation counting. The Rolling-up of oily soil from PET film was observed and change of contact angle and removal time were measured. The results were as follows ; 1. In the case of soaps and powder synthetic detergents, the optimum concentrations we-re about $0.2\~0.3\%$. And detergencies of liquid synthetic detergents were considerably low, and the detergency was continually increased up with increasing concentration to $0.5\%$, which seemed to be caused by the lower pH than that of soap and powder synthetic deter-gent solutions. 2. As the effect of external or internal fiber structure; the detergency of cotton was lower than that of polyester. 3. In the observation of Rolling-up, the contact angle increased and the Rolling-up time became shorter with increasing detergent concentrations ($0.05\~0.5\%$). And it was confirmed that detergency was increased with Rolling-up effect. In addition, the study on the actual laundry condition was studied using the questionaire. From the results, about $76\%$ of households used the concentration of detergent roughly or excessively and housewives were highly concerned on the recommended dose, but grade of practice were very low.

• Tribology and Lubricants
• /
• v.34 no.3
• /
• pp.75-83
• /
• 2018

Microturbomachinery (< 250 kW) using gas foil bearings can function without oil lubricants, simplify rotor-bearing systems, and demonstrate excellent rotordynamic stability at high speeds. State-of-the-art technologies generally use bump foil bearings or leaf foil bearings due to the specific advantages of each of the two types. Although these two types of bearings have been studied extensively, there are very few studies on leaf-bump foil bearings, which are a combination of the two aforementioned bearings. In this work, we illustrate a simple mathematical model of the leaf-bump foil bearing with leaf foils supported on bumps, and predict its static and dynamic performances. The analysis uses the simple elastic model for bumps that was previously developed and verified using experimental data, adds a leaf foil model, and solves the Reynolds equation for isothermal, isoviscous, and ideal gas fluid flow. The model predicts that the drag torques of the leaf-bump foil bearings are not affected significantly by static load and bearing clearance. Due to the preload effect of the leaf foils, rotor spinning, even under null static load, generates significant hydrodynamic pressure with its peak near the trailing edge of each leaf foil. A parametric study reveals that, while the journal eccentricity and minimum film thickness decrease, the drag torque, direct stiffness, and direct damping increase with increasing bump stiffness. The journal attitude angle and cross-coupled stiffness remain nearly constant with increasing bump stiffness. Interestingly, they are significantly smaller compared to the corresponding values obtained for bump foil bearings, thus, implying favorable rotor stability performance.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.568-573
• /
• 2016

We investigated the charging characteristics of a conducting solid sphere (glassy carbon sphere) comparing with that of a water droplet and check the applicability of the perfect conductor theory. For the systematic research, sphere size, applied voltages, viscosity of the medium were changed and the results were compared with that of corresponding water droplets and the perfect conductor theory. Basically, a glassy carbon sphere follows the perfect conductor theory but the charging amount was lower as much as 70~80% of theoretical prediction value due to oil film formed between electrode and a carbon sphere. We hope this result provides basic understandings on the solid sphere contact charging phenomenon and related applications.

• Tribology and Lubricants
• /
• v.28 no.6
• /
• pp.265-271
• /
• 2012

In the preceding Part I study, for improving the unbalance response vibration of a large PRT motor-generator rotor fundamentally by design, a series of design analyses were carried out for bearing improvement by retrofitting from original plain partial journal bearings, applied for operation at a rated speed of 1,800 rpm, to final tilting pad journal bearings. To satisfy evenly key basic lubrication performances such as the minimum lift-off speed and maximum oil-film temperature, a design solution of 5-pad tilting pad journal bearings and maximizing the direct stiffness by about two times has been achieved. In this Part II study, a detailed rotordynamic analysis of the large PRT motor-generator rotor-bearing system will be performed, applying both the original plain partial journal bearings and the retrofitted tilting pad journal bearings, to confirm the effect of rotordynamic vibration improvement after retrofitting. The results show that the rotor unbalance response vibrations with the tilting pad journal bearings are greatly reduced by as much as about one ninth of those with the plain partial journal bearings. In addition, for the tilting pad journal bearings there exist no critical speed up to the rated speed and just one instance of a concerned critical speed around the rated speed, whereas for the plain partial journal bearings there exist one instance of a critical speed up to the rated speed and two instances of concerned critical speeds around the rated speed.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.144-149
• /
• 2003

Carbon tips were grown on Si cantilevers by applying an electron beam to them directly with Scanning Electron Microscope. A carbon tip was fabricated by aligning the electron beam directly down the vertical axis of Si cantilever and then irradiating a single spot on the cantilever for a proper time in the dominant atmosphere of residual gases generated by the oil of the diffusion pump. A number of control parameters for SEM, including exposure time, acceleration voltage, emission current, and beam probe current, were allowed to make various aspect ratio feature. The growth of carbon tips was not affected by the surface morphology of substrates. We could acquired the tip whose effective length is 0.5 $\mu\textrm{m}$, bottom diameter is 90 nm and cone half angle $3.5^{\circ}$ The growth technique of the high aspect ratio carbon tips on the tip-free cantilevers is available to reduce the complexities of fabricating sub-micron scale tips on the PZT thin film actuator integrated AFM cantilevers.

• Korean Journal of Materials Research
• /
• v.24 no.8
• /
• pp.434-442
• /
• 2014

Serious environmental problems have been caused by the greenhouse effect due to carbon dioxide($CO_2$) or nitrogen oxides($NO_x$) generated by the use of fossil fuels, including oil and liquefied natural gas. Many countries, including our own, the United States, those of the European Union and other developed countries around the world; have shown growing interest in clean energy, and have been concentrating on the development of new energy-saving materials and devices. Typical non-fossil-fuel sources include solar cells, wind power, tidal power, nuclear power, and fuel cells. In particular, organic solar cells(OSCs) have relatively low power-conversion efficiency(PCE) in comparison with inorganic(silicon) based solar cells, compound semiconductor solar cells and the CIGS [$Cu(In_{1-x}Ga_x)Se_2$] thin film solar cells. Recently, organic cell efficiencies greater than 10 % have been obtained by means of the development of new organic semiconducting materials, which feature improvements in crystalline properties, as well as in the quantum-dot nano-structure of the active layers. In this paper, a brief overview of solar cells in general is presented. In particular, the current development status of the next-generation OSCs including their operation principle, device-manufacturing processes, and improvements in the PCE are described.

• Journal of Convergence for Information Technology
• /
• v.7 no.5
• /
• pp.53-58
• /
• 2017

In the age of oil exhaustion, low cost, semi-transparent solar cell, the dye-sensitized solar cell (DSC) has attracted significant attention since 1991 of $Gr{\ddot{a}}tzel$ report. To enhance the light-harvest capability of the photoelectric electrode, and efficiency of photoelectric transformation of the DSC, scattering layer of various structure have been proposed to photoelectric electrode materials. The scattering center of scattering layer needs the large titanium dioxide nanoparticles of 250 - 300 nm in diameter. In this study, the large sized $TiO_2$ nanocyrstals of around 300 nm were synthesized using the modified sol-gel process. According to the analysis of XRD and TEM, the synthesized $TiO_2$ nanoparticles exhibit single crystals of anatase phase. The optical transmittance of the synthesized titanium dioxide film prepared by spin coating is around 50% at 550 nm. It is suitable for scattering layer as a scattering center, and expected to enhance the efficiency of photoelectric transformation of the DSC.

• Solar Energy
• /
• v.11 no.3
• /
• pp.62-73
• /
• 1991

The purpose of the present work is to investigate the atomization characteristics and to find the available working conditions of given nozzles. Experimental investigations were carried out with the nozzles, "Delavan" and "Hago"(pressure atomizing simplex 1.25GPH), with $60^{\circ}$ and $80^{\circ}$ spray angles also at various nozzle pressures. In the present work, Sauter mean-diameter was utilized to describe the quality of the atomization. All sample droplets were microphotographed with high-contrust film at 50X magnification and analyzed by Nukiyama-Tanazawa distribution function. The $80^{\circ}$ spray angle gives better atomization function than $60^{\circ}$ spray angle, and available working conditions were set at approximately $8kg/cm^2$ nozzle pressure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.521-529
• /
• 2017

Three-dimensional flow characteristics within a high-acceleration first-stage turbine vane passage has been investigated in a newly-built vane cascade for propulsion. The result shows that there is a strong favorable pressure gradient on the vane pressure surface. On its suction surface, however, there exists not only a much stronger favorable pressure gradient than that on the pressure surface upstream of the mid-chord but also a subsequent adverse pressure gradient downstream of it. By employing two different oil-film methods with upstream coating and full-coverage coating, a four-vortex model horseshoe vortex system can be identified ahead of each leading edge in the cascade, and the separation line of inlet boundary layer flow as well as the separation line of re-attached flow is provided as well. In addition, basic flow data such as secondary flow, aerodynamic loss, and flow turning angle downstream of the cascade are obtained.