• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.299-307
• /
• 1996

The surface tension of PO added sodium poly(oxyethylene(EO), oxyisopropylene(PO)) dodecyl ether sulfate firstly were slightly lower than EO added sulfate in the concentration range of $10^{-6}{\sim}10^{-3}mol/{\ell}$. And they had lower critical micelle concentration ($10^{-4}{\sim}9{\times}10^{-5}mol/{\ell}$) than general anionic surfactants. The adsorptivity ($2.2{\times}10^{-10}mol/cm^2$) of sodium $(PO)_{10}(EO)_5$ dodecyl ether(compound of PO addition firstly) calculated by Gibbs' adsorption isotherm were higher than that of sodium $(EO)_{10}(PO)_5$, dodecyl ether(compound of EO addition firstly), but were lower than that of sodium dodecyl sulfate (${\Gamma}=3.2{\times}10^{-10}mol/cm^2$). These could be understood that the adsorption areas of compounds were very large because of their high molecular weight. Moreover, PO compounds showed better properties than EO compounds in foamability, emulsifying power for organics (n-hexane, benzene), detergency for the lard, tallow oil mixture and dispersability for iron oxide. It was interpreted in terms of surface properties of the PO compounds. These showed that the interfacial activity become higher when hydrophilic and hydrophobic portion existed in aggoromerated state respectively. The test results of emulsifying power for organics (n-hexane, benzene) showed better for benzene than n-hexane. Eight kinds of sodium (EO, PO) dodecyl ether derivatives showed irregular dispersibilities for polar iron oxide in water dispersed media.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3317-3326
• /
• 2011

Physicochemical properties of Achyranthes japonica and Smilax china extracts were investigated for the purpose of functionality research on the natural bio-resources. Extraction contents were order of distilled water>methanol>ethanol solvent, the highest free aminoacids were proline from Achyranthes japonica, phosphoserine and glutamic acid from Smilax china, respectively. BI and TAC by spectrophotometric absorbance were order of methanol>ethanol>water in Smilax china leaf extract, but water>methaol>ethanol in Achyranthes japonica leaf extract. EDA was high in ethanol extract from Smilax china leaf and in methanol extract from Smilax china root, and in water extract from Achyranthes japonica. TBA value of Achyranthes japonica leaf and Smilax china leaf-ethanol extracts on olive oil was 82.1% and 84.0%, respectively, for that of an artificial antioxidant BHT. Antimicrobial effect was observed in Achyranthes japonica stem-methanol extract on Bacillus subtillis, in Smilax china leaf-ethanol extract on Bacillus subtillis, Vibrio vulnificus and Salmonella enterica, respectively. And the adsorption of Pb(II) on Achyranthes japonica was higher than that of Cd(II) on Smilax china under the same metal ion concentration.

• Korean Journal of Food Science and Technology
• /
• v.46 no.3
• /
• pp.315-322
• /
• 2014

Immobilized lipases were prepared by physical adsorption using lipase AK, AY, AH, PS and R on Amberlite$^{(R)}$XAD$^{(R)}$7 HP resin. With the immobilized lipases (10%), structured lipid was synthesized by enzymatic interesterification of canola oil, palmitic ethyl ester, and stearic ethyl ester in order to study the reaction characteristics. Among the lipase, the highest protein content was obtained from lipase AH (11.41%) before immobilization, while the highest levels of bound protein was observed from immobilized lipase AK (63.91%). Immobilized lipase AK had the highest interesterification activity (38.3% of total saturated fatty acid). Lipase AK was also used for a continuous reaction in which the slow flow of reactant resulted in increased reaction rate. Reusability of immobilized AK, AH and PS increased at the second reaction (120-196.5%). However, the activity of immobilized AK, which had the highest bound protein content (63.91%) decreased after the third reaction, while the activity of immobilized AH and PS was maintained until the sixth reaction.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.98-107
• /
• 2023

This study presents a well spacing design for coalbed methane(CBM) reservoirs using the experimental results of methane gas adsorption measurement of coal samples obtained from North Kalimantan Island, Indonesia. The gas productivity analysis shows that the cumulative gas production increases as the Langmuir volume increases. This indicates that the maximum gas adsorption directly affects the gas production. In addition, the maximum gas production increases with the increase of reservoir permeability, and the dewatering period is shortened. In particular, the cumulative gas production increases as the production influence area increases. However, when comparing productivity per unit well, the maximum cumulative gas production is found between 2,000 ft of depth and 80-160 acres of the influence area. When reservoir depth and production influence area are considered simultaneously, the results of the appropriate well depth and spacing calculations show that gas productivity is highest between 600-2,000 ft. In this case, it is appropriate to design well spacing in the range of 80-160 acres. Therefore, well spacing design considering coalbed depth in undeveloped CBM reservoirs can be accomplished using gas sorption test results from coal samples.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.925-937
• /
• 1996

Three types of mordenites treated by steaming($SM_{6.5}$), HF solution for $SM_{6.5}(FM_a)$ and HF solutlon+steaming for $SM_{6.5}(FM_b)$ were prepared and used as cracking catalysts of vacuum gas oil. These samples were analysed by XRF and XPS for average and surface Si/Al atomic ratio, XRD for unit cell constants, nitrogen adsorption/desorption for porosity, pyridine-IR for acidic properties. In comparison with three type samples, $SM_{6.5}$ had a lot of acid amount and showed micropore volume mostly(>85% to total volume). Dealuminated $FM_a$, compared with $SM_{6.5}$, was decreased a little in acid amount and improved for porosity. Also, $FM_b$ was decreased further in acid amount and developed in mesopore dramatically. The catalytic activity and the yield of gasoline, kerosine+diesel and branched aromatic over the modified mordenites which have developed mesopore were improved. This is due to limited access of diffusion of large molecules within pore of the modified mordenites.

• Applied Chemistry for Engineering
• /
• v.31 no.4
• /
• pp.429-437
• /
• 2020

In this study, a cationic gemini surfactant was synthesized using isosorbide, in order to modify the alkyl chain length in the range of C₁₀~C₁₆. The c.m.c and surface tension of the synthesized cationic gemini surfactant were measured to be in the ranges of 5.13 × 10^-4~1.62 × 10^-4 mol/L and 31.86~37.41 dyne/cm, respectively. The surface tension increased with increasing the length of the alkyl group. In addition, as the area per molecule occupied by the surfactant adsorbed on the interface increased with the reduced extent of adsorption, the bubble generation at the air-water interface decreased. The emulsifying capacity in benzene was maintained above 60 ± 5% after 8 h while that in soybean oil tended to decrease above 50 ± 5%. The performance was superior in benzene, a highly hydrophobic substance, and the emulsion stability was shown to be consistent beyond 1 h during the preparation of pre-emulsion in oil and water. The antimicrobial activity was dependent on the length of the hydrophobic chain of the synthesized cationic gemini surfactant due to the increased size of the clean zone in Escherichia coli (E.coli) and Staphylococcus aureus.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.38-45
• /
• 2009

In this study, interfacial properties were measured for imidazoline type cationic surfactant system which has been widely used as a fabric softener, a dispersant, an anti-static agent, a bleach activator, and an emulsifier. The CMC of imidazoline surfactant was near $6{\times}10^{-5}mol/L$ and the surface tension at CMC was about 32 mN/m. It was found that surface tension was not affected by surfactant concentration but decreased with an increase in pH. The interfacial tension between 1 wt% aqueous solution and n-dodecane was shown to be about 0.01 mN/m and equilibration time was not affected by pH. Phase behavior experiment in a binary aqueous surfactant system showed that only micellar solution of $L_1$ phase was found under conditions of temperature and pH investigated during this study. Only a two-phase region consisting of lower-phase microemulsion in equilibrium with excess oil phase existed under the same conditions, when oil was added to the binary surfactant system. The foam stability measured with 1 wt% surfactant solution increased with pH, which is consistent with surface tension measurement result. QCM(quartz crystal microbalance) measurement showed that surfactant adsorption increased with surfactant concentration but decreased with pH. According to the friction measurement, best fabric softening effect by imidazoline surfactant system was found under alkali conditions.

• Journal of Adhesion and Interface
• /
• v.25 no.2
• /
• pp.63-68
• /
• 2024

In this study, the contamination of gold(Au) wire according to the types of rinse applied for surface treatment in the wire bonding process is investigated and confirmed. For the surface treatment, rinses containing silicon(Si) or those based on organic materials are mainly employed. To identify their effects, surface treatment is conducted on Au wire using two types of rinse at a 1.0 wt% concentration, referred to as Si-including and Oil-based rinse-coated Au wire. Subsequently, a simulation experiment is performed to verify the reactivity of dust containing Si components that could occur in the semiconductor process. Through optical microscopy (OM) and scanning electron microscopy(SEM) analysis, it is observed that a larger amount of dust is adsorbed on the surface of Si-including rinse-coated Au wire compared with the Oil-based rinse-coated Au wire. This is attributed that the rinse containing Si components is relatively polar, causing polar interactions with dust, which also has polarity. Therefore, it is expected that using a rinse without Si components can reduce contamination caused by dust, thereby decreasing the defect rate in the practical wire bonding process.

• Carbon letters
• /
• v.22
• /
• pp.1-13
• /
• 2017

Porous materials play a vital role in science and technology. The ability to control their pore structures at the atomic, molecular, and nanometer scales enable interactions with atoms, ions and molecules to occur throughout the bulk of the material, for practical applications. Three-dimensional (3D) porous carbon-based materials (e.g., graphene aerogels/hydrogels, sponges and foams) made of graphene or graphene oxide-based networks have attracted considerable attention because they offer low density, high porosity, large surface area, excellent electrical conductivity and stable mechanical properties. Water pollution and associated environmental issues have become a hot topic in recent years. Rapid industrialization has led to a massive increase in the amount of wastewater that industries discharge into the environment. Water pollution is caused by oil spills, heavy metals, dyes, and organic compounds released by industry, as well as via unpredictable accidents. In addition, water pollution is also caused by radionuclides released by nuclear disasters or leakage. This review presents an overview of the state-of-the-art synthesis methodologies of 3D porous graphene materials and highlights their synthesis for environmental applications. The various synthetic methods used to prepare these 3D materials are discussed, particularly template-free self-assembly methods, and template-directed methods. Some key results are summarized, where 3D graphene materials have been used for the adsorption of dyes, heavy metals, and radioactive materials from polluted environments.

• Membrane and Water Treatment
• /
• v.11 no.2
• /
• pp.97-109
• /
• 2020

Membrane fouling is the main drawback of membrane technology. Frequent membrane cleaning and membrane replacement are, therefore, required to reduce membrane fouling that causes permeate flux reduction, lower rejection, or higher operating pressure. Studies have proved that the alteration of membrane properties is the key controlling factor in lessening membrane fouling. Among stimuli-responsive membranes, thermo-responsive membrane is the most popular, with a drastic phase transition and swelling-shrinking behavior caused by the temperature change. In this study, the thermo-responsive ability of two commercial membranes, PolyCera® Titan membrane and PolyCera® Hydro membrane, at different temperatures was studied on the antifouling function of the membrane in palm oil mill effluent (POME) treatment. The evaluation of the membrane's thermo-responsive ability was done through three cycles of adsorption (fouling) and desorption (defouling) processes in a membrane filtration process. The experimental result depicted that PolyCera® Hydro membrane had a higher membrane permeability of 67.869 L/㎡.h.bar than PolyCera® Titan membrane at 46.011 L/㎡.h.bar. However, the high membrane permeability of PolyCera® Hydro membrane was compensated with low removal efficiency. PolyCera® Titan membrane with a smaller mean pore size had better rejection performance than PolyCera® Hydro membrane for all tested parameters. On the other hand, PolyCera® Titan membrane had a better hydrodynamic cleaning efficiency than PolyCera® Hydro membrane regardless of the hydrodynamic cleaning temperature. The best hydrodynamic cleaning performed by PolyCera® Titan membrane was at 35℃ with the flux recovery ratio (FRR) of 99.17 ± 1.43%. The excellent thermo-responsive properties of the PolyCera® Titan membrane could eventually reduce the frequency of membrane replacement and lessen the use of chemicals for membrane cleaning. This outstanding exploration helps to provide a solution to the chemical industry and membrane technology bottleneck, which is the membrane fouling, thus reducing the operating cost incurred by the membrane fouling.