• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2001년도 추계학술대회 논문집
• /
• pp.92-99
• /
• 2001

• Wind and Structures
• /
• 제8권5호
• /
• pp.325-342
• /
• 2005

This paper deals with the buckling behavior of thin-walled aboveground tanks under wind load. In order to do that, the wind pressures are obtained by means of wind-tunnel experiments, while the structural non linear response is computed by means of a finite element discretization of the tank. Wind-tunnel models were constructed and tested to evaluate group effects in tandem configurations, i.e. one or two tanks shielding an instrumented tank. Pressures on the roof and on the cylindrical part were measured by pressure taps. The geometry of the target tank is similar in relative dimensions to typical tanks found in oil storage facilities, and several group configurations were tested with blocking tanks of different sizes and different separation between the target tank and those blocking it. The experimental results show changes in the pressure distributions around the circumference of the tank for half diameter spacing, with respect to an isolated tank with similar dimensions. Moreover, when the front tank of the tandem array has a height smaller than the target tank, increments in the windward pressures were measured. From the computational analysis, it seems that the additional stiffness provided by the roof prevents reductions in the buckling load for cases even when increments in pressures develop in the top region of the cylinder.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.297-302
• /
• 2003

This study was carried out to check the contingency planning methods under the analysis of oil spill potential and make a guide line to apply the results to the port of Busan. The expected spilled oil drift patterns are considered with the most probable scenarios under the base of the oil spill potential. The results obtained from this study are as follows: (1) Analysis method of oil spill potent was proposed and the applicability was proved by the application example to the port of Busan to make the contingency plan. (2) Responsible oil spill contingency planning methods / flow are suggested considered environmental factors and the oil spill potential. (3) The coastal waters of Busan was consist of rocky flat, man-made solid shore and beach shore. Marine traffic have high density of oil tanker and cargo ship. Also, oil tanker ship are examined in the small ships to be less than 3000t to supply oil to the ship moored / anchored as well as the large amount of oil tank / basin are located along the coast of Busan port. These systems are introduced to make in put data to the analysis of oil spill potential. (4) According to the analysis of historical records of oil spill accident in Busan, the frequency of accidents by cargo ship rank highest and 45% of accidents is caused by carelessness. about 65% of total accidents shows a small spill accident of less than $10k{\ell}$.

• 한국식품과학회지
• /
• 제36권2호
• /
• pp.211-216
• /
• 2004

회분식 반응기(stirred-tank batch reactor)를 사용한 DAG, MAG 함유 기능성유지를 비용매계(solvent-free system) 조건에서 효소적 반응을 이용하여 합성하였다. 48시간 동안 합성된 지질을 HPLC를 사용한 TAG, 1,3-DAG, 1,2-DAG 및 MAG 함량 분석결과 각각 45.05, 16.27, 23.05 및 14.98%로 분석되었으며 체중개선 기능성 유지의 지방산 조성 분석결과 palmitic, palmitoleic, stearic, oleic, linoleic 및 linolenic acid가 13.21, 0.15, 2.02, 34.36, 49.12 및 1.14 mol%로 분석되었다. 합성된 지질의 ${\alpha},\;{\gamma}$ 및 ${\delta}-tocopherol$ 함량을 분석한 결과는 각각 0.014, 0.029 및 0.010%로 분석되었으며 총 tocopherol 함량은 0.053%로 나타났다. 또한 재구성된 지질을 사용하여 산가, 비누화가, 요오드가를 측정하였으며 융점 및 결정화점을 살펴보고 이를 통하여 옥수수유로 유래된 DAG, MAG를 함유한 체중개선 기능성 유지의 이화학적, 물리적 특징을 규명하였다. 체중개선 기능성 유지의 산화 안정성 실험을 시행한 결과 체중개선 기능성 유지가 원료유인 옥수수유보다 높은 과산화물가와 p-anisidine가를 보였으며 각기 달리 혼합한 rosemary추출물(100, 200 및 300ppm)이 체중개선 기능성 유지와 옥수수유의 산화를 감소 시켰다.

• 한국해양공학회지
• /
• 제35권6호
• /
• pp.393-402
• /
• 2021

As greenhouse gas emissions from maritime transport are increasing, the International Maritime Organization is continuously working to strengthen emission regulations. Liquefied natural gas (LNG) fuel is less advantageous as a point of CO₂ reduction due to the methane leakage that occurs during the bunkering and operation of marine engines. In this study, greenhouse gas emissions from an LNG-fueled ship were analyzed from the perspective of the life cycle. The amount ofmethane emission during the bunkering and operation procedures with various boil-off gas (BOG) treatment methods and gas engine specifications was analyzed by dynamic simulation. The results were also compared with those of other liquid fuel engines. As a result, small LNG-fueled ships without a BOG treatment facility emitted 32% more greenhouse gas than ships utilizing marine gas oil or heavy fuel oil. To achieve a greenhouse gas reduction via a BOG treatment method, a gas combustion unit or re-liquefaction system must be mounted, which results in a greenhouse gas reduction effect of about 25% and 30%. As a result of comparing the amount of greenhouse gas generated according to the BOG treatment method used with each tank size from the perspective of the operating cycle with the amounts from using existing marine fuels, the BOG treatment method showed superior effects of greenhouse gas reduction.

• 한국소음진동공학회논문집
• /
• 제12권3호
• /
• pp.195-203
• /
• 2002

In the engine room and the aft part areas of the ship, there exist so many tank structures contacting with fresh water or sea water or oil. If these structures exhibit excessive vibrations during the sea trials, it takes a lot of cost, time and effort to improve vibration situation because the reinforcement work requires emptying the fluid out of the tanks, additional welding and special painting. It is therefore very important to predict a precise vibration characteristics of the tank structures at the design stage, however it is not easy to estimate vibration characteristics of the structures because of difficulties for accurate evaluation of the added (or virtual) mass effect due to the fluid inside the tank. In this paper, numerical and experimental approaches have been performed to present same fundamental data necessary for anti-vibration design of tank structures contacting with fluid, by investigating vibration behaviors of rectangular tank structure for various water depths.

• 한국안전학회지
• /
• 제21권1호
• /
• pp.86-91
• /
• 2006

Oil spills caused by the accidents have been occurred from house and factory waste, grounded tanker, the rupture of storage tank and oil pipelines, the deterioration of various industrial facilities, etc. Many oil spills result in contamination of shorelines and workplace. Fire and explosion may happen from these spills. There are several technologies used for clean-up application, which include use of oil dispersing agents, absorbents, solidifiers, booms and skimmers by physical, chemical, and biological methods. Methods for oil spill clean-up operation are classified into the absorption type, gel type and self-swelling type. Porous materials with oil absorptive properties are classified into micropore, mesopore, and macropore depending on their pore sizes. Recently, new porous materials with smaller size have been developed, but the selective oil absorption in water-in-oil interface demonstrates the macro pore size. In this study oil absorption effects were evaluated using the organic porous materials with a complex function of gel type and swelling type. Samples were subjected to analysis by FT-IR spectroscopy and were characterized in terms of gel formation and morphologies. Oil sorption capacity, pressure retention force and gel strength were also measured. From these results, the physicochemical reactivity before and after gelation was verified and the industrial applications of clean-up operation were suggested.

• 한국기계가공학회지
• /
• 제20권3호
• /
• pp.122-128
• /
• 2021

Machining operations require removal of chips to keep the coolant clean and fresh throughout the operation time. In this study, microchip removal equipment was developed using AutoCAD and CATIA programs for 3D modeling and 2D draft. In addition, the flow analysis and electromagnetic field analysis of the equipment were performed using the COMSOL Multiphysics program. The flow design of the coolant oil tank was realized on the basis of fluid analysis results. Further, on the basis of magnetic density analysis, a conveyer was designed for effectively removing metal microchips in the tank by using arrays of neodymium permanent magnets.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.71-76
• /
• 2005

Marine structures are often in contact with inner or outer fluid as stern, ballast and oil tanks. The effect of interaction between fluid and structure has to be taken into consideration when we estimate the dynamic response of the structure appropriately. Fatigue damages can also be sometimes observed in these tanks which seem to be caused by resonance. Thin walled tank structures in ships which are in contact with water and located near engine or propeller where vibration characteristics are strongly affected by the added mass of containing water. Therefore it is essentially important to estimate the added mass effect to predict vibration characteristics of tank structures. But it is difficult to estimate exactly the magnitude of the added mass because this is a fluid-structure interaction problem and is affected by the free surface, vibration modes of structural panels and the depth of water. I have developed a numerical tool of vibration analysis of 3-dimensional tank structure using finite elements for plates and boundary elements for fluid region. In the present study, the effect of added mass of containing water, the effect of structural constraint between panels on the vibration characteristics are investigated numerically and discussed. Especially a natural frequencies by the fluid interaction between 2 panels and a breath mode of the water tank are focused on.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2013년도 특별논문집
• /
• pp.13-20
• /
• 2013

In this paper, a collision accident of a container/Ro-Ro ship was numerically analyzed. A container trailer collided with a longitudinal bulkhead of the ship in the accident, which constituted a longitudinal wall of a heavy fuel oil tank. Due to the accident, the bulkhead plate was ruptured and the heavy fuel oil spilled out of the tank. The detailed information regarding the collision velocity and the mass of the trailer was not provided. Therefore, several collision accident scenarios were constructed based upon the arrangement of the ramp way. Each collision accident scenario was analyzed to predict the extents of damage using a commercial numerical package, ABAQUS. Based on the analysis results it is proposed how to minimize the extents of damage. Through the investigations performed in this study it was found that the understandings of various damages due to collision accidents and the developments of structural design guidance against collision are necessary for the betterment of Container/RO-RO ships' performance.