• Korean Journal of Agricultural and Forest Meteorology
• /
• v.9 no.2
• /
• pp.100-108
• /
• 2007

The Gwangneung KoFlux supersite, located in a rugged mountain region, is characterized by a low wind speed due to a mountain-valley circulation and rolling terrain. Therefore, it is essential to understand the effect of coordinate rotation on flux measurements by the eddy-covariance method. In this paper, we review the properties of three orthogonal coordinate frames (i.e., double, triple, and planar fit rotations) and apply to flux data observed at the Gwangneung supersite. The mean offset of vertical wind speed of sonic anemometer was inferred from the planar fit (PF) coordinate rotation, yielding the diurnal variation of about $\pm0.05ms^{-1}$. Double rotation $(\bar{v}=\bar{w}=0)$ produced virtually the same turbulent fluxes of heat, water, and $CO_2$ as those from the PF rotation under windy conditions. The former, however, resulted in large biases under calm conditions. The friction velocity, an important scaling parameter in the atmospheric surface layer, was more sensitive to the choice of coordinate rotation method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.924-931
• /
• 2002

Vacuum interrupters in order to be used in various switch-gear components such as circuit breakers, distribution switches, contactors, etc. spread the arc uniformly over the surface of the contacts. The electrodes of vacuum interrupters are made of sinter-forged Cu-Cr materials for good electrical and mechanical characteristics. Since the closing velocity is 1-2m/s and impact deformation of the electrode depends on the strain rate at that velocity, the dynamic behavior of the sinter-forged Cu-Cr is a key to investigate the impact characteristics of the electrodes. The dynamic response of the material at the high strain rate is obtained from the split Hopkinson pressure bar test using disc-type specimens. Experimental results from both quasi-static and dynamic compressive tests are Interpolated to construct the Johnson-Cook model as the constitutive relation that should be applied to simulation of the dynamic behavior of the electrodes. The impact characteristics of a vacuum interrupter are investigated with computer simulations by changing the value of five parameters such as the initial velocity of a movable electrode, the added mass of a movable electrode, the wipe spring constant, initial offset of a wipe spring and the virtual fixed spring constant.

• Journal of Digital Contents Society
• /
• v.12 no.2
• /
• pp.177-184
• /
• 2011

This study deals with Timing Synchronization of motion picture and music in film music's physical point of view. Timing Synchronization appears by using Click Track, which calculates time of picture and location of bar. We also can find Hit, the emphasis point of music, by computation Frame Per Beat and estimate the location of note per time. Hit can be placed at upbeat, but, because of music's characteristic, it is more convenient to composer when it's placed at downbeat. Therefore, this study suggests three methods to sync the music and picture. First of all, sync through time conversion, second of all, sync through tempo conversion, and lastly, there is way to sync through offset. These each methods have their pros and cons, so choice should be made based on the music's natural flow.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.259-259
• /
• 1999

TiC ceramic particulate-reinforced titanium matrix composites were fabricated and the resultant densification, microstructure, and static and dynamic mechanical properties were studied. Comparing Ti with TiH₂powders as host materials for TiC ceramic reinforcement by pressureless vacuum sintering, TiH₂-started composites showed better sinterability and resistance to both elastic and plastic deformation than Ti-started ones. When TiH₂and TiH₂-45 vol.%TiC samples were hot pressed, TiH₂matrices transformed to alpha prime Ti and alpha Ti phase, respectively. It is interpreted that the diffusion of an alpha stabilizer carbon from TiC into the matrix is one of the plausible reasons far such a microstructural difference. The 0.2% offset yield strengths of the hot pressed TiH₂and TiH₂-45 vol.%TiC samples were 1008 and 1446 MPa, respectively, in a static compressive mode (strain rate of 1×$10^{-3}$/s). Dynamic compressive strengths of the samples were 1600 and 2060 MPa, respectively, at a strain rate of 4×10³/s.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.939-951
• /
• 2002

We propose a new multiscale Galerkin method based on interpolation wavelets for two-dimensional Poisson's and plane elasticity problems. The major contributions of the present work are: 1) full multiresolution numerical analysis is carried out, 2) general boundaries are handled by a fictitious domain method without using a penalty term or the Lagrange multiplier, 3) no special integration rule is necessary unlike in the (bi-)orthogonal wavelet-based methods, and 4) an efficient adaptive scheme is easy to incorporate. Several benchmark-type problems are considered to show the effectiveness and the potentials of the present approach. is 1-2m/s and impact deformation of the electrode depends on the strain rate at that velocity, the dynamic behavior of the sinter-forged Cu-Cr is a key to investigate the impact characteristics of the electrodes. The dynamic response of the material at the high strain rate is obtained from the split Hopkinson pressure bar test using disc-type specimens. Experimental results from both quasi-static and dynamic compressive tests are Interpolated to construct the Johnson-Cook model as the constitutive relation that should be applied to simulation of the dynamic behavior of the electrodes. The impact characteristics of a vacuum interrupter are investigated with computer simulations by changing the value of five parameters such as the initial velocity of a movable electrode, the added mass of a movable electrode, the wipe spring constant, initial offset of a wipe spring and the virtual fixed spring constant.

• Wind and Structures
• /
• v.23 no.2
• /
• pp.157-169
• /
• 2016

The structural integrity of tube bundles represents a major concern when dealing with high risk industries, such as nuclear steam generators, where the rupture of a tube or tubes will lead to the undesired mixing of the primary and secondary fluids. Flow-induced vibration is one of the major concerns that could compromise the structural integrity. The vibration is caused by fluid flow excitation. While there are several excitation mechanisms that could contribute to these vibrations, fluidelastic instability is generally regarded as the most severe. When this mechanism prevails, it could cause serious damage to tube arrays in a very short period of time. The tubes are therefore stiffened by means of supports to avoid these vibrations. To accommodate the thermal expansion of the tube, as well as to facilitate the installation of these tube bundles, clearances are allowed between the tubes and their supports. Progressive tube wear and chemical cleaning gradually increases the clearances between the tubes and their supports, which can lead to more frequent and severe tube/support impact and rubbing. These increased impacts can lead to tube damage due to fatigue and/or wear at the support locations. This paper presents simulations of a loosely supported multi-span U-bend tube subjected to turbulence and fluidelastic instability forces. The mathematical model for the loosely-supported tubes and the fluidelastic instability model is presented. The model is then utilized to simulate the nonlinear response of a U-bend tube with flat bar supports subjected to cross-flow. The effect of the support clearance as well as the support offset are investigated. Special attention is given to the tube/support interaction parameters that affect wear, such as impact and normal work rate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.476-477
• /
• 2013

반도체의 성능은 최근 10년 사이에 급격하게 발전했고 아날로그 및 디지털 회로 소자들에 있어 저전력/고속 특성 요구가 커지고 있다 [1]. 상온에서 30,000 $cm^2$/Vs 이상의 전자 이동도를 가지며 큰 conduction band offset을 갖는 InAs/AlSb 2차원전자가스(2DEG) 소자는 Spinorbit-interaction의 값이 매우 커서 SPIN-FET 소자로 크게 주목받고 있다 [2]. 본 발표자들은 GaAs 기판위에 성장한 InAs 2DEG HEMT 소자의 전/자기적인 특성과 고속반응 물질로 주목 받는 InSb 박막소자의 doping 특성에 따른 전기적/물리적인 특성의 평가에 대해 그 결과를 소개하고자 한다. 격자정합과 Semi-insulating 기판의 부재로 상용화되어 있는 GaAs와 InP 기판위에 물질차이에 따른 고유의 한계 특성을 줄이기 위한 Pseudomorphic이라 불리는 특별한 박막 성장 기법을 적용하여 높은 전자 이동도를 가지며 spin length가 길어 Spin-FET로서 크게 주목받고 있는 InAs 2DEG HEMT 소자를 완성시켰다. 60,000 ($cm^2$/Vs) 이상의 높은 전자 이동도를 갖는 소자의 구현을 목표로 연구를 진행하였으며 1.8 K에서 측정된 Spin-orbit interaction의 값은 6.3e-12 (eVm)이다. InAs/InGaAs/InAlAs 및 InGaAs/InAlAs 구조의 InP 기반의 소자에서 보다 큰 값으로 향후 Spin-FET 응용에 크게 기대하고 있다. 또한, GaAs 기판위에 구현된 InSb 소자는 격자부정합 감소를 위해 InAs 양자점을 사용하여 약 $2.6{\mu}m$ 두께로 구현된 InSb 박막 소자는 상온에서 약 60,400 ($cm^2$/Vs)의 상온 전자이동도를 보였으며 현재 동일 두께에서 세계 최고결과(~50,000 $cm^2$/Vs)에 비해 월등하게 높은 값을 보이고 있다. Hall bar pattern 공정을 거쳐 완성된 소자는 측정 결과 10~20% 이상 향상된 전자 이동도를 보였다. 2e18/$cm^3$ 미만의 p-doping의 경우, 상온에서 n-type 특성을 보이나, 저온에서 p-type으로 변하는 특성을 보였고 n-doping의 경우 5e17/$cm^3$까지는 전자 이동도만 감소하고, doping에 의한 효과는 크게 없었다. 1e18/$cm^3$의 높은 doping을 할 경우 carrier가 증가하는 것을 확인했다. 이상의 측정 결과로 Spin-FET 소자로서 아주 우수하다는 것을 확인할 수 있었고 n-/p- type이 특성을 고려한 high quality InSb 박막소자의 응용을 위한 중요한 정보를 얻을 수 있었다.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.353-359
• /
• 2020

In this study, the controller structure and control algorithm of medical robot bed developed for pressure ulcer prevention and healing are described. The existing pressure ulcer prevention mattress is operated manually and the remaining maximum body pressure exceeds the pressure of ulcer generation, so there is always room for pressure ulcers. However, the system developed in this study does not generate the pressure ulcers because the body pressure drops to zero when the keyboard of the bed descends using the active electric driving keyboard. In addition, even if the bed is raised and the pressure above the critical body ulcer pressure is abnormal, the device and the control algorithm are designed so that the lasting time is within the pressure ulcer generation critical time and the pressure ulcer itself is not generated. The bed key board motor is a motor designed with the BLDC servos suitable for medical use and these can communicate each other easily through CAN(Car Area Network). The system is new medical robot bed that is effective in preventing pressure ulcers and will be distributed to many patients suffering from pressure ulcers.