• KIEE International Transactions on Power Engineering
• /
• v.4A no.4
• /
• pp.178-191
• /
• 2004

This paper presents a new approach to HVDC system control for damping subsynchronous oscillation (SSO) involving HVDC converters and turbine generator shaft systems. This requires a novel eigenvalue analysis (NEA) program, derivation of HVDC system modeling considering steady-state conditions and dynamic conditions in the combined AC/DC system, and an appropriate control scheme. The method suggested makes possible the design of a subsynchronous oscillation damping controller (SODC) to provide positive damping torque for the range of torsional modes in combined AC/DC systems. There are three steps involved in the design of a SODC； first the worst torsional mode is determined using the NEA program, next the SODC parameters are designed for the range of that torsional mode, and then finally an off-line simultaneous time domain program such as PSCAD/EMTDC is used to verify the parameters of the SODC. The suggested SODC design method is applied to two AC/DC systems, and its practicality is verified using the PSCAD/EMTDC simulation program.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.363-364
• /
• 2010

Most LED drivers uses current control method to adjust LED current. Using AC power grid such as off-line converter, Buck topology is popular because input voltage of LED driver is much higher than LED output voltage. Normally DCM current control is more popular than CCM current mode control in the range of below 50W, But DCM characteristics are dependent on the input voltage variation. This paper deals with what should be considered in DCM for LED driver with valley fill circuit.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.164-173
• /
• 2009

In this paper, two new circuit structures for European and U.S. ultra-wide band(UWB) bandpass filters(BPFs) with sharp roll-off characteristics are introduced. We show first that the ultra-wide bandpass property is obtained from a $\lambda$/4 open T resonator with a capacitively coupled $\lambda$/4 short-circuited line, which provides two attenuation poles at lower and upper cutoff frequencies. Then, two identical capacitively coupled input/output lines, which can be $\lambda$/4-length open ends or $\lambda$/2-length short ends, with the T-resonator, are adopted to suppress lower and higher frequency components outside of the pass band. There is coupling between the input and output lines providing two additional transmission zeros in the lower and upper transition bands of the filter. Since the coupling between the T-resonator with the $\lambda$/4 short-circuited line and the input/output lines limits the bandwidth of the filter to the European UWB band, both the $\lambda$/4 short-circuited line and the input/output lines are inserted between the two stacked T-resonators for the U.S. UWB band. The filter structures are simulated with ADS and HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.18-23
• /
• 2006

The formation degree of sustain (ITO pattern) determines the quality of a PDP (Plasma Display Panel). Thus, in the present study, we attempt to detect 100% of the defects that are larger than $30{\mu}m$. Currently, the inspection method in the PDP manufacturing process is dependent upon the naked eye or a microscope in off-line mode. In this study, a prototype inspection system for PDP ITO patterned glass is developed. The developed system, which is based on a line-scan mechanism, obtains information on the defects and sorts the defects by type automatically. The developed inspection system adopts a multi-vision method using slit-beam formation for minimum inspection time and the detection algorithm is embodied in the detection ability. Characteristic defects such as pin holes, substances, and protrusions are extracted using the blob analysis method. Defects such as open, short, spots and others are distinguished by the line type inspection algorithm. It was experimentally verified that the developed inspection system can detect defects with reliability of up to 95% in about 60 seconds for the 42-inch PDP panel.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.8 s.350
• /
• pp.91-96
• /
• 2006

High efficiency switching mode circuits such as class I amplifiers have been well known in the MHz frequency range. The class E amplifier is a type of switching mode amplifier offering very high efficiency approaching 100%. In this paper, the class E amplifier has been designed by using the harmonic balance method of circuit simulator. The designed amplifier is realized by using pHEMT and microstrip line, shows 66% power added efficiency (PAE) at 2.4GHz with 17.6dBm output power. With -3dBm input power of wireless LAN, measured output spec01m can meet the required IEEE 802.11g standard spectrum mask. That means the required amplifier back off of 9dB from $P_{ldB}$ to satisfy the required wireless LAN spectrum mask.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.2
• /
• pp.131-136
• /
• 2001

A new analysis method of lumped-element directional coupler for CATV was proposed, where the even-and odd-mode theory for a symmetrical coupled-line directional coupler was applied to a transformer-type directional coupler. In addition, the tap-offs were analyzed by the proposed theory, which are widely used in CATV (Cable Television) systems. By comparing the calculated results for S-parameters results to the measured ones using only the even-and odd-mode reflection coefficients, the validity of the proposed analysis method was confirmed. Then, it was clearly shown that the tap-off has very wide bandwidth from 5 MHz to 4,000 MHz by adopting the proposed theory.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.346-351
• /
• 2001

A new analysis method was proposed, where the even . odd-mode theory for a symmetrical coupled-line directional coupler was applied to a transformer-type directional coupler. In addition, the tap-offs were analyzed by the proposed theory, which are widely used in CATV (Cable Television), DBS (Direct Broad- casting Satellite), CS (Communication Satellite) systems. By comparing the calculation results to the measured ones using the even . odd-mode reflection coefficients only, the validity of the proposed analysis method was confirmed. Then, the tap-off has been broadened from 5 MHz over 4,000 MHz by adopting the proposed theory.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.51-55
• /
• 2007

Generally, PLC (Power Line Communication) based home automation devices such as wall switch, walt socket, gas controller, etc, must maintain wake-up status at all time to control other electronic devices and monitor their on/off status whether they are in service or not. In order to reduce the unnecessary energy consumption during the standby mode, the new power-saving PLC 2 ports wall switch has been developed, separating PLC communication part and controller part and introducing sleep mode. In addition, to expand life cycle of PLC product and to reduce the rate of product failure in active mode, the instant controlling method in controlling process is adopted instead of the maintenance controlling method. In comparison to the earlier model, the new 2 ports PLC wall switch has reduced power by 0.95[W] less in standby mode and 3.2[W] less in active mode than the previous one.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.105-114
• /
• 2015

Heated glasses are widely used to prevent surface condensation and freezing in ship and building windows. This study proposes a heated glass temperature control system composed of power and control circuits to control the temperature of heated glasses. The proposed temperature control system adopts a digital controller instead of a conventional analog controller. Thus, the proposed system has better characteristics, such as precise setup and control of glass temperature, setup and control of output power, and control mode change between ON/OFF and phase controls. The system can also implement multi-functional control algorithms. The control characteristics are not dependent upon external disturbances, such as ambient temperature and electrical noises. Furthermore, the proposed temperature control system utilizes the power line communication (PLC) method to control the number of heated glasses without any extra communication lines. The system proposes a new communication protocol with strong immunity to electrical switching noises. A new sensorless algorithm is used to detect the temperature of the heated glass. This study presents the design guidelines in detail and its effectiveness are confirmed by implementing a 4-kw prototype temperature control system.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.4
• /
• pp.1730-1747
• /
• 2018

Multi-view video plus depth (MVD) is a mainstream format of 3D scene representation in free viewpoint video systems. The advanced 3D extension of the high efficiency video coding (3D-HEVC) standard introduces new prediction tools to improve the coding performance of depth video. However, the depth video in 3D-HEVC is time consuming. To reduce the complexity of the depth video inter coding, we propose a fast coding unit (CU) size and mode decision algorithm. First, an off-line trained Bayesian model is built which the feature vector contains the depth levels of the corresponding spatial, temporal, and inter-component (texture-depth) neighboring largest CUs (LCUs). Then, the model is used to predict the depth level of the current LCU, and terminate the CU recursive splitting process. Finally, the CU mode search process is early terminated by making use of the mode correlation of spatial, inter-component (texture-depth), and inter-view neighboring CUs. Compared to the 3D-HEVC reference software HTM-10.0, the proposed algorithm reduces the encoding time of depth video and the total encoding time by 65.03% and 41.04% on average, respectively, with negligible quality degradation of the synthesized virtual view.