• 항공우주기술
• /
• 제12권2호
• /
• pp.108-117
• /
• 2013

가스발생기용 산화제 개폐밸브는 파일롯 공압으로 포핏을 열고 스프링 힘에 의해 닫음으로써 로켓엔진의 추진제 유량을 제어한다. 현재 개발 중인 산화제 개폐밸브는 액추에이터에서 압력을 제거하면 닫히도록 설계되어 있다. 그러므로 밸브의 성능을 평가하기 위해 밸브가 열리고 닫히는 특성에 따라 힘 평형 상태를 분석할 필요가 있다. 밸브가 닫히기 시작하는 시점의 작동 유체의 압력을 결정하고, 포핏이 열리는 시점의 압력을 결정되어 힘평형이 설계되어 있다. 인증시험 수준에서의 극저온 유동 시험 하에서 채터링 현상은 금속 기밀부에서 다량의 누설이 발생했다. 힘평형 계산을 이용한 산화제 밸브의 채터링이 발생된 시점의 압력은 약 11 bar로 예측 된다.

• 한국정보통신학회논문지
• /
• 제9권6호
• /
• pp.1253-1259
• /
• 2005

본 논문은 외부의 서지로부터 컴퓨터 네트워크회로의 보호를 위한 서지방호장치에 대하여 기술하였다. 서지방호장치는 동작속도가 빠른 아발란시 다이오드와 에너지 내량이 큰 가스튜브의 하이브리드형으로 구성하였으며, 고주파 대역에서의 삽입손실을 줄이기 위하여 고속회복 다이오드를 사용하였다. 제안한 서지전압 차단장치의 성능 평가를 위하여 국제규격 IEC 61000-4-5 및 IEC 61643-21에 따라 서지차단특성과 신호전송 특성평가를 수행하였다. 실험결과로부터 본 서지차단장치는 국제규격에 제시된 서지차단특성을 만족하였으며, -3dB의 고역차단 주파수가 204 MHz로 100 Mbps급 근거리 통신네트워크에 적합한 특성을 나타내었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권2호
• /
• pp.232-237
• /
• 2011

최근 초저온 밸브 관련 산업의 급속한 발전과 함께 초저온 밸브에 대한 지속적인 연구가 이루어지고 있고 특히, 기계, 조선, 반도체 및 디스플레이 산업, 항공 우주산업분야의 비약적인 발전과 사용자의 요구 등으로 인하여 초저온용 밸브의 고성능화가 되고 있는 추세이나, 진공 단열에 관한 초저온 응용 장비들에 대한 기술개발 및 연구는 미흡한 실정이다. 본 연구에서는 초저온용 진공자켓밸브의 스템 외부에 자켓 배관을 설치 한 후 낮은 압력을 유지함으로써 외부로부터 자켓 내부로의 유입 열전달량을 감소시키는 것에 주안점을 두었고, 효과적인 전열 제어를 위하여 외부로부터 자켓 내부로의 유입 열전달량을 감소시킬수 있는 자켓 내부의 압력과 자켓부의 두께 변화에 관한 열전달 특성을 3차원 수치해석적인 방법으로 연구하여 고찰하였다.

• 한국수산과학회지
• /
• 제36권2호
• /
• pp.136-143
• /
• 2003

The eggs of Favonigobius gymnauchen attached on the under side of a small stone were collected off Seongsan-eup Cheju-do in August, 2000 to investigate their development of egg, larvae and juveniles. The fertilized eggs were elliptical in shape (mean long axis: 1.50 mm; mean short axis: 0.57 mm) and transparent. There were filaments on one side of the egg membrane. Larvae hatched at 48 hrs 50 mins after morula stage with 25-26 myotomes in $22.8-28.5^{\circ}C\;(mean\;24.7^{\circ}C).$ The newly hatched larvae were 2.31-2.49 mm (mean 2.37 mm n=10) in total length (TL) and their mouth and anus were already opened. Their melanophores were appeared on the over gas globule, around anus and the part of caudal peduncle with 24-25 myotomes. At 4-5 days after hatching. larvae attained 3.81-4.07 mm (mean 3.96 mm, n=10) in TL and their yolk sac was completely absorbed. They began to eat rotifer and transformed to postlarvae stage. At 14 days after hatching, postlarvae attained 6.17-6.31 mm (mean 6.21 mm, n=10) in TL and their caudal notocord was flexed $45^{\circ}$ upward. At 24 days after hatching, postlarvae attained 8.69-9.10 mm (mean 8.87 mm, n=10) in TL had reached the juvenile stage. All fins were formed with the complete set of fin rays with the following counts: dorsal fin rays IV-I, 9-10; anal fin rays I, 9; pectoral fin rays 17; ventral fin rays: I, 5; caudal fin rays: 9+8= 17.

• 전기화학회지
• /
• 제9권4호
• /
• pp.170-177
• /
• 2006

고분자 전해질 연료전지의 분리판의 유동채널 설계는 고전류밀도에서 발생하는 농도분극에 직접적인 영향을 줄 뿐 아니라 생성되는 물의 효과적인 전달을 위하여 매우 중요하다. 평행류 유로와 interdigitated 유로의 성능비교를 위하여 연료극과 공기극이 포함된 완전한 형태의 고분자 전해질 연료전지의 3차원 수치해석모델을 개발하였다. 수치해석모델을 사용하여 평행류 유동장과 interdigitated 유동장의 압력강하, 채널간의 물질전달, $H_2O$와 $O_2$의 농도 분포 그리고 i-V 성능을 비교하였다. 그 결과 물질전달에서 채널간의 대류에 의한 물질전할이 더욱 우수한 interdigitated 유동채널에서 성능이 더 높게 나타났으며 압력강하는 보다 크게 나타나 설계시 두가지 성능에 대한 상호보완이 필요함을 알 수 있었다.

• 한국방재학회 논문집
• /
• 제1권1호
• /
• pp.157-163
• /
• 2001

본 연구의 목적은 청정실 내부에서 가상의 화재가 발생할 경우 화재 확산 및 연기의 전파 현상을 예측하기 위하여 실시하였다. 청정실 내의 화재로 인한 온도 및 속도분포의 해석은 유한체적법을 이용한 수치적 방법으로 해석하였으며 난류유동장의 계산은 표준 $k-{\varepsilon}$ 모델을 적용하여 실시하였다. 본 연구 결과는 화재발생 후 150초가 지난 후에는 화재가 완전히 성장한 것으로 나타났으며 이 경우 환기장치는 화재가 완전히 성장한 후에 정지하는 것으로 가정하였다. 연기의 질량분율은 온도 분포와 거의 유사한 것으로 나타났다. 따라서 청정실에서 화재가 발생할 경우 화재 성장이 60초 내에 전공간의 $20{\sim}30%$까지 확산되므로 내부에 있는 사람은 30초 이내에 대피하는 것이 바람직하다.

• International Journal of Korean Welding Society
• /
• 제2권2호
• /
• pp.26-31
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired fer car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. In the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6NO 1 alloy welds. Aluminum alloy plate of 2.Omm in thickness with filler metal bar was welded by twin beam Nd: YAG laser facility (total power: 5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 1/min was used. The defocusing distance is kept at 0 mm. At travel speeds off 3 to 9 and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• 한국농공학회논문집
• /
• 제57권5호
• /
• pp.113-122
• /
• 2015

This study aims to evaluate future stream flow by the operation of agricultural reservoir group at the upper stream of the Miho River. Four agricultural reservoirs with storage capacities greater than one million cubic meters within the watershed were selected, and the RCP 8.5 climate change scenario was applied to simulate reservoir water storage and stream flow assuming that there are no changes in greenhouse gas reduction. Reservoir operation scenarios were classified into four types depending on the supply of instream flow, and the water supply reliability of each reservoir in terms of water supply under different reservoir operation scenarios was analyzed. In addition, flow duration at the watershed outlet was evaluated. The results showed that the overall run-off ratio of the upper stream watershed of the Miho River will decrease in the future. The future water supply reliability of the reservoirs decreased even when they did not supply instream flow during their operation. It would also be difficult to supply instream flow during non-irrigation periods or throughout the year (January-December); however, operating the reservoir based on the operating rule curve should improve the water supply reliability. In particular, when instream flow was not supplied, high flow increased, and when it was supplied, abundant flow, ordinary flow, and low flow increased. Drought flow increased when instream flow was supplied throughout the year. Therefore, the operation of the agricultural reservoirs in accordance with the operating rule curve is expected to increase stream flow by controlling the water supply to cope with climate change.

• Journal of Trauma and Injury
• /
• 제27권4호
• /
• pp.229-232
• /
• 2014

A 55 year-old man hit a vehicle while riding a bicycle. He was diagnosed as left hemopneumothorax, multiple rib fracture, cerebral hemorrhage, and skull fracture. Initially he suffered from hypoxia requiring 100% oxygen with a mechanical ventilator. Finally he became hypotensive. Venovenous extracorporeal membrane oxygenation (ECMO) was initiated to support patient's gas exchange. Because hypotension and left ventricular dysfuction persisted, we converted the mode of support to veno-arterio-venous ECMO. Over four days of intensive care, we could wean off ECMO. The patient went to rehabilitation facility after 45 days of hospitalization. Although trauma and bleeding are considered as relative contraindication of ECMO, careful decision making and management may enable us to use ECMO for trauma-related refractory heart and/or lung failure.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.436-437
• /
• 2012

Double patterning technology (DPT) has been suggested as a promising candidates of the next generation lithography technology in FLASH and DRAM manufacturing in sub-40nm technology node. DPT enables to overcome the physical limitation of optical lithography, and it is expected to be continued as long as e-beam lithography takes place in manufacturing. Several different processes for DPT are currently available in practice, and they are litho-litho-etch (LLE), litho-etch-litho-etch (LELE), litho-freeze-litho-etch (LFLE), and self-aligned double patterning (SADP) [1]. The self-aligned approach is regarded as more suitable for mass production, but it requires precise control of sidewall space etch profile for the exact definition of hard mask layer. In this paper, we propose etch end point detection (EPD) in spacer etching to precisely control sidewall profile in SADP. Conventional etch EPD notify the end point after or on-set of a layer being etched is removed, but the EPD in spacer etch should land-off exactly after surface removal while the spacer is still remained. Precise control of real-time in-situ EPD may help to control the size of spacer to realize desired pattern geometry. To demonstrate the capability of spacer-etch EPD, we fabricated metal line structure on silicon dioxide layer and spacer deposition layer with silicon nitride. While blanket etch of the spacer layer takes place in inductively coupled plasma-reactive ion etching (ICP-RIE), in-situ monitoring of plasma chemistry is performed using optical emission spectroscopy (OES), and the acquired data is stored in a local computer. Through offline analysis of the acquired OES data with respect to etch gas and by-product chemistry, a representative EPD time traces signal is derived. We found that the SE-EPD is useful for precise control of spacer etching in DPT, and we are continuously developing real-time SE-EPD methodology employing cumulative sum (CUSUM) control chart [2].