• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.111-114
• /
• 2005

The isolation performance of the S-band single-pole single-throw (SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide (GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9dB is obtained with the coplanar wire-bond interconnection (CWBI) at 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion (IMD3) are less than 2.43 dB over 2.5 CHz $\sim$ 4 GHz and greater than 64 dBc.

• Journal of Mechanical Science and Technology
• /
• v.18 no.8
• /
• pp.1327-1337
• /
• 2004

An efficient multi-objective optimization method is presented making use of neural network and a systematic satisficing trade-off method (STOM), in order to simultaneously improve both maneuverability and durability of tire. Objective functions are defined as follows: the sidewall-carcass tension distribution for the former performance while the belt-edge strain energy density for the latter. A back-propagation neural network model approximates the objective functions to reduce the total CPU time required for the sensitivity analysis using finite difference scheme. The satisficing trade-off process between the objective functions showing the remarkably conflicting trends each other is systematically carried out according to our aspiration-level adjustment procedure. The optimization procedure presented is illustrated through the optimum design simulation of a representative automobile tire. The assessment of its numerical merit as well as the optimization results is also presented.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.863_864
• /
• 2009

Design and drive characteristics of SR drive for hydraulic pump system using passive converter is presented in this paper. In oder to get the high performance, a simple passive circuit is added in the front-end of a conventional asymmetric converter, which consists of three diodes and one capacitor. This passive converter has the high demagnetization voltage, to reduce the demagnetization time. Futhermore optimal turn-off angle for the proposed passive converter is proposed. According to motor speed and current, an optimal turn-off angle can be achieved by look-up table to reduce torque ripple. The characteristic of proposed hydraulic pump system using passive converter is verified by simulation and experimental results.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.11
• /
• pp.73-79
• /
• 1997

This paepr is concerned with the design of linear parameter varying filter that ensures H$^{2}$/$H^{\infty}$ performance for a class of linear parameter varying(LPV) plants. The state space matrices of plant are assumed to be dependent affinely on a vector of time varying parameter, and each parameter is assumed to be measured in real time. Using the linear matrix inequalities(LMIs), we can solve the synthesis problem and the solution of LMIs is carried out off-line. The designed filter is parameter varying and automatically scheduled along parameter trajectories. Because the solution of LMIs is carried out off-line, computation time of filter gain is reduced. The validity of the proposed algorithm is verifed through computer simulation..

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.986-996
• /
• 1994

Insulation system of LNG carrier has made important roles such as maintaining a proper Boil off Ratio(BOR) for the cargo and avoiding the excessive low temperature of the adjacent inner hull beyond the permissible limit. At the same time, safety and economy of the LNG transportation by the ship are connected with the performance of the insulation system. Also, thermal insulation system of LNG carrier is one of the most advanced technique with the structure analysis of tank, welding and assembling. In this study a computer program is developed to calculate the hull temperature distribution and BOR, which are important factors in thermal design for the Moss Rosenberg Verft spherical tank type LNG carrier. Detailed results for hhull temperature distribution close to LNG tank, BOR and the thickness effect of insulation material are reported in this paper in the range of standare design sea condition.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2006.09a
• /
• pp.15-22
• /
• 2006

Global strength check for TLP tendon body can be estimated based on maximum tendon tensions and bending moments, which are resulted in TLP global performance analysis. Final tendon length, especially thread length on Length Adjustment Joint, is easily calculated with water depth at TLP in-place location, TLP lock-off draft and unlocking length of tendon bottom section. And LAJ thread length, which is locked with TLP top tendon connector, should be carefully determined with tendon design and installation tolerances.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.10
• /
• pp.1296-1309
• /
• 1999

A three dimensional compressible Navier-Stokes code is developed to analyze flowfields and performance of a vaned diffuser in a centrifugal compressor. It employs scalar implicit approximate factorization, finite volume formulation, second order upwind differencing and a two-equation $q-{\omega}$ turbulence model based on the integration to the wall. Pressure recovery and loss coefficients of a vaned diffuser are evaluated using a developed computer code. The simulated three dimensional flows show how through flow structure affects pressure recovery performance and loss coefficients of a vane for design and off-design inlet flow angles. Development of complex three dimensional flow over the inlet region and leading edge are very influential to the overall flow and performance.

• Tribology and Lubricants
• /
• v.28 no.5
• /
• pp.197-202
• /
• 2012

In this study, with the purpose of fundamentally improving the unbalance response vibration of a large PRT motor-generator rotor by design, a performance improvement design analysis is carried-out by retrofitting tilting pad bearings, replacing the plain partial journal bearings that were originally applied for operation at a rated speed of 1,800 rpm. In this process, a goal of the design analysis is to obtain a design solution for maximizing the direct stiffness of the bearings while satisfying the key basic lubrication performance requirements such as the minimum lift-off speed and maximum oil-film temperature. The results show that with a careful design application of tilting pad journal bearings for operation at such a relatively low speed of 1,800 rpm, direct stiffness increment of the bearings by about two times can be effectively achieved. Prevention of pad unloading is also considered in the analysis. Moreover, the designs of elliptical and offset half journal bearings are also analyzed and reviewed.

• Archives of design research
• /
• v.16 no.4
• /
• pp.443-452
• /
• 2003

This study is to find out the possibility of applying the Blended Learning which combines the advantage of face-to-face classroom instruction and e-Learning to design education. This Blended Loaming Model has five steps such as 'prepare, teach, show, interact, and collaborate'. It is designed by the learning decision points (performance outcomes, content stability and structure, audience size, and so on) and the characteristics of delivery methods(asynchronous, synchronous). This research is based on the learners' satisfaction data of each step. The number of the participants is 27 and a questionnaire with 21 items is administered. Ten items of them are designed with 5-point Likert scales and the rest of them ask learners describe the reason of their selection. The result show that learners are satisfied with the blended learning than the off-line classroom. It is expected that the blended learning can be a substitute of the off-line classroom for the effectiveness of design education.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.1
• /
• pp.1211-1217
• /
• 2001

This paper presnts a controller for the heat capacity of thermal storage systems using off-peak electricity which is composed of an identifier using neural networks and a storage time adjuster in order to store exactly the required thermal energy without loss. Since thermal storage systems have nonlinear characteristics and large time constant, even if we predict the heating load accurately, it is very difficult to store exactly the required thermal energy. Thus, in the neural network for the identifier, the adaptive learning rate for high learning speed and bit inputs based on state changes of thermal storage power source are used. Also a hardware for the controller using a microprocessor is developed. The performance of the proposed controller is shown by experiment.