• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.99-104
• /
• 2006

There are several advantages to make use of a bridge pier for the tidal power generation. Current velocity increases near the pier, therefore the tidal power generation becomes more efficient because the power is proportional to the cubic of the current velocity. The pier is convenient for access and maintenance of the hydraulic turbine and the power unit. The project is now underway at the Ikitsuki Bridge in Tatsuno-Seto Strait of Nasasaki Prefecture, where the tidal current was measured by the bottom mount ADCP for almost one year. Model experiments for a Darrieus water turbine with two and three straight blades were carried out in the circulating water channel, in which the power coefficients of the turbine were obtained as a function of blade section and the attaching angle of a blade to the rotor. Those experimental results are discussed to obtain an optimum Darrieus turbine for tidal power generation.

• Ocean and Polar Research
• /
• 제30권2호
• /
• pp.207-213
• /
• 2008

An interest in deep-sea measurements has been gradually increased in association with global warming and the need for deep-sea resources development. Long-term mooring of current meters has been recently conducted primarily for these purposes. In general, current meters equipped on a mooring line are deployed and recovered for a planned period in the sea. This paper describes all the preparations for deep-sea mooring. It also reviews the possible causes of the failures of recovery, which occasionally happens in the sea.

• 수산해양기술연구
• /
• 제16권1호
• /
• pp.43-47
• /
• 1980

The author designed and tested the high sensitive three-phase power factor meter and relay circuit, and dealt with the circuit to detect the phase of the current and the voltage. An operational amplifier comparator circuit and two single-phase transformers are used to control and detect the phase angle between the current and the voltage. The results obtained are as follows: 1. Converting the sine wave input current into the constant amplitude rectangular wave form by using a transistor chopper circuit, the power factor can be measured precisely over the load current of 0.08 A. 2. Using the moving coil type current meter, the power factor meter can be read in uniform . scale all over the range. 3. Using the three-phase power factor meter, the power factor relay which works at any power factor can be made.

• 수산해양기술연구
• /
• 제12권1호
• /
• pp.19-24
• /
• 1976

A series of physical oceanographic investigations of the circulation in the Kwang Bay' were carried out seven times from May 1974 to May 1975 every other month. The average water transports through the southern entrance of the' Kwang Yang Bay were approximately $1,014{\times}I0^6m^3$/half-tide in ebb current and $278{\times}10^6m^3$$405.6{\times}I0^6m^34/half-tide in ebb current, and $282{\times}10^6m^3 $/half-tide in flood current, at the maximum current intensity. The water from Seomjin River flows into the bay at an annual average rate of $84{\times}I0^6m^3$/half-tide, the rate being fluctuated from month to month from $6.0\times}10^6m^3 $to $11. 5{\times}I0^6m^3 $per half-tide.

• 한국해양공학회지
• /
• 제30권4호
• /
• pp.320-326
• /
• 2016

Rip current forecasts, based on intensity, are marked in four levels—notice, watch, warning, and danger. However, numerical results are represented by current vectors, whose magnitudes are then converted into predictive levels. In the present study, the rose diagram is adapted as a determinative forecasting index and examined for the case of an ideal rip channel consisting of surface, bottom, and averaged currents. Further, it is employed in the sensitivity analysis of wave-induced currents generated by wave conditions at the Haeundae Beach. The simulation of surface onshore and bottom undertow currents is accomplished by including a mass flux term in the wave-averaged continuity equation.

• 한국표면공학회지
• /
• 제49권2호
• /
• pp.166-171
• /
• 2016

Cathodic protection is widely recognized as the most cost effective and technically appropriate corrosion prevention methodology for the port, offshore structures, ships. When applying the cathodic protection method to metal facilities in seawater, on the surface of the metal facilities a compound of calcium carbonate($CaCO_3$) or magnesium hydroxide($Mg(OH)_2$) films are formed by $Ca^{2+}$ and $Mg^{2+}$ ions among the many ionic components dissolving in the seawater. And calcareous deposit films such as $CaCO_3$ and $Mg(OH)_2$ etc. are formed by the surface of the steel product. These calcareous deposit film functions as a barrier against the corrosive environment, leading to a decrease in current demand. On the other hand, the general calcareous deposit film is a compound like ceramics. Therefore, there may be some problems such as weaker adhesive power and the longer time of film formation uniting with the base metal. In this study, we tried to determine and control the optimal condition through applying the principle of cathodic current process to form calcareous deposit film of uniform and compact on steel plate. The quantity of precipitates was analyzed, and both the morphology, component and crystal structure were analyzed as well through SEM, EDS and XRD. And based on the previous analysis, it was elucidated mechanism of calcareous deposit film formed in the sacrificial anode type (Al, Zn) and current density (1, 3, $5A/m^2$) conditions. In addition, the taping test was performed to evaluate the adhesion.

• 수산해양기술연구
• /
• 제22권4호
• /
• pp.32-40
• /
• 1986

A model experiment of purse seine by the circulating water tank was carried out on the changes of net shape and the tension of purseline under operation in two layer current. In the circular tank, the two layer current was made by cutting off the current of upper layer and producing the bottom current by the equipment shown in Fig. 1. The model experiment of purse sein was made on a reduced scale 1 :400, and the experiment was carried out according to the Tauti's model law. When the bottom current of O. 5 knot flows to lower part of three-eighths of net, following results are derived. The depth of sinkerline reached only about 80% of that of no current set. The horizontal shift of sinker line caused by the bottom current is maximized in tight set. The enclosed area by the floatIine immediately after the completion of set net is 61. 5% in tight set, 50. 0 % in loose set and 54. 1 % in lateral set of those in the case of no current. In the first half period of pursing, the tension of the purseline is enhenced by the bottom current and the pattern of increasing is irregular in the tension curves.

• 해양환경안전학회지
• /
• 제12권4호
• /
• pp.285-291
• /
• 2006

소리도와 욕지도 사이 해역의 유동 분포를 파악하기 위하여 2004년 5월, 6월, 10월 및 11월에 ADCP를 이용하여 정선관측 및 정점관측을 실시하였다. 25시간 정선관측에 따른 평균류의 연직분포는 욕지도 남서해역에서 북동류의 흐름이 우세하게 나타났다. 또한 25시간 정점관측 결과를 보면 상층과 하층의 경계수심이 $15\sim20m$에 존재함을 알 수 있었고, 상 하층으로의 유동분포가 다르고 상층과 하층의 변화폭이 작게 나타났다. 동서 성분 및 남북 성분에 대판 해수 수송량의 계산결과는 남서방향으로의 수송량보다 북동방향으로의 수송량이 더 크게 나타났다.

• Ocean Systems Engineering
• /
• 제12권1호
• /
• pp.87-142
• /
• 2022

An analysis for the computation of Fatigue Damage Index (FDI) under the effects of the various combination of the ocean loads like random waves, current, platform motion and VIV (Vortex Induced Vibration) for a certain design water depth is a critically important part of the analysis and design of the marine riser platform integrated system. Herein, a 'Computer Simulation Model (CSM)' is developed to combine the advantages of the frequency domain and time domain. A case study considering a steel catenary riser operating in 1000 m water depth has been conducted with semi-submersible. The riser is subjected to extreme environmental conditions and static and dynamic response analyses are performed and the Response Amplitude Operators (RAOs) of the offshore platform are computed with the frequency domain solution. Later the frequency domain results are integrated with time domain analysis system for the dynamic analysis in time domain. After that an extensive post processing is done to compute the FDI of the marine riser. In the present paper importance is given to the nature of the current profile and the VIV. At the end we have reported the detail results of the FDI comparison with VIV and without VIV under the linear current velocity and the FDI comparison with linear and power law current velocity with and without VIV. We have also reported the design recommendations for the marine riser in the regions where the higher fatigue damage is observed and the proposed CSM is implemented in industrially used standard soft solution systems (i.e., OrcaFlex^*TM and Ansys AQWA^**TM), Ms-Excel^***TM, and C++ programming language using its object oriented features.

• 한국CDE학회논문집
• /
• 제17권1호
• /
• pp.45-53
• /
• 2012

In this paper, oil spreading simulation model is proposed for analyzing the oil spreading phenomenon rapidly when the ocean is polluted by the oil from a stranded ship. The space occupied by the ocean is converted into the latticed cell, and the each cell contains the information, such as the quantity of the oil, the temperature of the ocean, and the direction of current and wind. Two states, such as "clean" and "polluted" are defined in the each cell, and the oil in the cell spreads to the neighbor cells by the spreading rules. There are three spreading rules. First, the oil in the certain cell only spreads to the neighbor cells that contain larger oil than the certain cell. Second, the oil evaporates in proportion to the temperature of the ocean at the every time step. Third, the oil spreading property is affected by the direction and the speed of the current and the wind. The oil spreading simulation model of the each cell is defined by using the combined discrete event and discrete time simulation model architecture with the information and the spreading rules in the cell. The oil spreading simulation is performed when the oil of 10,000 kL is polluted in the ocean environment of 300 m by 300 m with various current and wind.