• Journal of the Korean Home Economics Association
• /
• v.18 no.3
• /
• pp.5-11
• /
• 1980

The study carried out to clarify the effects of lard and corn oil on serum total cholesterol content and liver thiobarbituric acid (TBA) value in ethanol (Et-OH) fed mice. Results obtained from the present study were a follows: 1. serum total cholesterol content was considerably increased by 25% Et-OH administration in mice. In case of 25% Et-OH plus Lard group and Lard group both group were also increased significantly to compare with normal value of mice but 25% Et-OH plus lard group was shown very higher value rather than that of Lard group and Lard group was found similar tendency to compare with the 25% Et-OH plus saline group except to after the 1 day. 2. serum total cholestrol content of 25% Et-OH plus Corn oil group and corn oil group were also increased significantly to compare with normal value, but the 25% Et-Oh plus Corn oil group slightly higher level than that of Corn oil group except to after the 3 days. 3. Lard group was also very similar tendency to compare with the corn oil group except to the 3 days. 4. liver TBA value was increased by 25% Et-OH fed mice. 25% Et-OH plus Lard group and Lard group were also increased significantly to compare with liver TBA value in normal mice, but 25% Et-OH plus Lard group was found higher value rather than that of lard group and 25% Et-OH group (Control). Lard group was similar to that of Control group except to after the 1 day. And 25% Et-OH plus Corn oil group was considerably increased rather than that of Control group, and liver TBA value of the above group was similar to that of 25% Et-OH plus Lard group except to after the 3 days. Corn oil group was shown lower value than that of lard group, but it was no significant.

• Journal of the Korean Institute of Gas
• /
• v.5 no.4 s.16
• /
• pp.79-84
• /
• 2001

In this study, the effect of polyol structure(OH-value, functionality) on the reactivity, mechanical property and cell morphology of polyurethane foam and the possibility of replacing HFC-36smfc was examined by evaluating how each blowing agent(CFC-11, HCFC-l4lb, HFC-36smfc) affects the reactivity, mechanical property and cell morphology. Results of the experiment showed that as the functionality and OH-value of polyol increased, there was an increase in the temperature profile, reaction rate, density and compressive strength. However. as the functionality and OH-value increased. the ceil size became smaller The use of different kinds of blowing agents did not appear to have and significant influence on the temperature profile, reaction rate, density and compressive strength. The foam using HFC-365mfc produced more uniform cells compared to the foam using HCFC-l4lb.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.115-123
• /
• 2003

Simultaneous measurements of velocity and OH distribution were made using particle image velocimetry(PIV) and planar laser-induced fluorescence(PLIF) of OH radical in turbulent hydrogen nonpremixed flames with coaxial air. The OH radical was used as an approximate indicator of chemical reaction zone. The OH layer was correlated well with the stoichiometric velocity, $U_s$, instantaneously and on average. In addition, high strain-rate regions almost coincide with the OH distribution. The residence time in flame surface, calculated from the root-mean-square value of the radial velocity, is proportional to $(x/d_F)^{0.7}$. It is found that the mean value of principal strain rate on the OH layer can be scaled with $(x/d_F)^{-0.7}$ and therefore, the product of the residence time and the mean strain rate remains constant over all axial positions.

• Textile Coloration and Finishing
• /
• v.9 no.3
• /
• pp.18-26
• /
• 1997

Polyester microfiber fabrics were decomposed at 100, 110, and 12$0^{\circ}C$ in saturated CaO/ethylene glycol solutions(CaO/EG), and the characteristics of decomposition kinetics were discussed in comparison to those by hot aqueous hydroxide solution(NaOH). The Arrhenius pre-exponential factor(A) was 9.17x $10^{14}$/M $sec^{-1}$and the activation energy($E_{a}$) was 8.19kcal/mol. While the A value was 1.947x $10^{14}$/M $sec^{-1}$ and the ($E_{a}$ value was about 15~19kcal/mol in NaOH-PET decomposition reaction. The much higher A value of the CaO/EG-PET decomposition reaction means that CaO/EG-PET decomposition reaction will occur in a less selective fashion in comparison to the NaOH-PET decomposition reaction. On the other hand, the lower ($E_{a}$) value of the CaO/EG-PET decomposition reaction than that of the NaOH-PET decomposition reaction means that CaO/EG-PET decomposition reaction is less sensitive on the variation of temperature than NaOH-PET decomposition reaction.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.189-189
• /
• 1982

This study was carried out to determine the possibility of making fiberboard through the dry forming process, utilizing the tannin-like material of the Asplund pulp from the silk worm oak as a binder. The fiberboard was made through paraformaldehyde treatment, spray of NaOH solution and adjustment of mat moisture content, by hot-pressing at $220^{\circ}C$, and 50-6-50kg/$cm^2$ pressure with 6-min. (0.6-1.8-3.6) three-stage pressing cycle. The results are summarized as follows: 1. The modulus of rupture value of fiberboard treated with NaOH solution was greater than that of untreated. The value was increased in proportion to the paraformaldehyde content from I to 5%, but there was no increasing between 5 and 7% paraformaldehyde content. The value became higher along with the increase of mat moisture content from 15% to 25%. 2. The water adsorption of fiberboard treated with NaOH solution was lower than that of untreated. The value was de"creased in proportion to the paraformaldehyde content from 1 to 5%, but there was no decreasing between 5 and 7% paraformaldehyde content.. 3. A good quality fiberboard (modulus of rupture value of about 250kg/$cm^2$) was made through 5% paraformaidehyde treatment and 3% treatment of 10% NaOH solution, when the mat moisture content was 25%. was 25%.

• Korean Journal of Materials Research
• /
• v.26 no.10
• /
• pp.513-520
• /
• 2016

The effect of NaOH concentration on the properties of electrolytic plasma processing (EPP) coating formed on AZ61A Mg alloy is studied. Various types of EPP were employed on magnesium alloy AZ61A in a silicate bath with different concentrations of NaOH additive. Analysis of the composition and structure of the coating layers was carried out using an X-ray diffractometer (XRD) and a scanning electron microscope (SEM). The results showed that the oxide coating layer mainly consisted of MgO and $Mg_2SiO_4$; its porosity and thickness were highly dependent on the NaOH concentration. The Vickers hardness was over 900 HV for all the coatings. The oxide layer with 3 g/l of NaOH concentration exhibited the highest hardness value (1220 HV) and the lowest wear rate. Potentiodynamic testing of the 3 g/l NaOH concentration showed that this concentration had the highest corrosion resistance value of $2.04{\times}10^5{\Omega}cm^2$; however, the corrosion current density value of $5.80{\times}10^{-7}A/cm^2$ was the lowest such value.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.20 no.3
• /
• pp.155-160
• /
• 2000

This syudy was conducted to increase the utility of forage rye which are suitable to be cultivated at high altitude Taekwllyong area. For that purpose two cultivars of rye (winter-more, kool-glazer) were cultivated for 3years using a randomized block design with 3 replications. The dry matter digestibility (DMD) was evaluated with the pelleted rye hay produced by adding sodium hydroxide and then the TDN value was calculated by the DMD. By adding NaOH, DMD and TDN value of rye pellets (Y=46.92+ 1.8X, ~ 0 . 9 7 )w ere increased significantly (p<0.05) and NDF (neutral detergent fiber) decrease significantly. However, ADF (acid detergent fiber) and lignin did not significantly decrease (p<0.05). Rye could be cultivated as a second crop after com at high altitude area in the same year and pelleted with NaOH in order to increase the nutritive values (p< 0.05). (Key words : Dry matter digestibility (DMD), Forage rye, NDF, ADF, Sodium hydroxide)

• Journal of Environmental Science International
• /
• v.13 no.1
• /
• pp.79-87
• /
• 2004

Esterification of soybean oil with methanol was investigated. First of all, liquid-liquid equilibriums for systems of soybean oil and methanol were measured at temperatures ranging from 40 to 65$^{\circ}C$. Profiles of conversion of soybean oil with time were determined from the glycerine content in reaction mixtures for the different kinds of catalysts, such as NaOH, CaO, Ca(OH)$_2$, MgO, Mg(OH)$_2$, and Ba(OH)$_2$. The effects of dose of catalyst, cosolvent and reaction temperature on final conversion were examined. Esterification of waste vegetable oil with methanol was investigated and compared to the case of soybean oil. Solubility of methanol in soybean oil was substantially greater than that of soybean oil in methanol. When the esterification reaction of soybean oil was catalyzed by solid catalyst, final conversion was strongly dependent on the alkalinity of the solid catalyst, and increased with the alkalinity of the metal. Hydroxides from the alkali metals were more effective than oxides. When Ca(OH)$_2$ was used for the esterification catalyst, maximum value of final conversion was measured at dose of 4％. When CHCl$_3$ as a cosolvent, was added into the reaction mixture of soybean oil which catalyzed by Ba(OH)$_2$, maximum value of final conversion was appeared at dose of 3％. When waste vegetable oil was catalyzed by NaOH and solid catalysts, high final conversion, over 90％, and fast reaction rate were obtained.

• Journal of Radiation Protection and Research
• /
• v.1 no.1
• /
• pp.15-21
• /
• 1976

The present investigation was intended to study the state of Pm-147 in solution and its adsorbed state on membrane filters by varying the concentrations of Pm-147 solution and its pH. Also, the study on the coprecipitation of Pm-147 with $Fe(OH)_3$ was carried out by varying, amounts of $Fe(OH)_3$ and pH of the solution. The carrier-free Pm-147 exists in an ionic state of $Pm^{3+}$ in solution, and is adsorbed on membrane filter in filtration process. The adsorbed state of Pm-147 on the membrane filter shows various ionic state at a constant ionic strength of 0.1M NaCl, that is, $Pm^{3+}$ state exists until pH value of 5.0, then gradually $Pm(OH)^{2+}$ state appears between pH value of 5.0 to 6.0, and the state of $Pm(OH)_2^+$ and $Pm(OH)_3$ would be expected at the higher pH value of 6.0. Coprecipitation of Pm-147 on $Fe(OH)_3$ is an adsorption penomenon in an ionic state of $Pm^{3+}$ in acidic condition. At higher pH and larger amount of Fe carrier, the adsorbed state of Pm-147 shows $Pm(OH)^{2+}$ and $Pm(OH)_2^+$ state. As a results of the present studies, it is seen that the characteristic of carrier free radioisotopes is not due to the radioactivity, but due to the adsorption of ultramicroquantity of radioisopes. Therefore, the knowledge on the ultramicroquantity of radioisotopes could help for the solution of decontamination in handing and chemical procedure with radioisotopes.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.8
• /
• pp.428-434
• /
• 2016

This study evaluated the efficacy of Ti-based coagulants on phosphorus (P) removal from municipal wastewater and compared them with Al-based coagulants. Jar test experiments were performed at various chemical doses and OH/Ti molar ratio (B value). The higher the intial phosphate ($PO_4-P$) concentration, the lower the [Ti]/[P] to reach a residual concentration below 0.2 mg P/L. Removal efficiencies of total phosphorus increased with an increased coagulant dose but decreased after the efficiencies reached their maximum value regardless of coagulant or B value. On the other hand, $PO_4-P$ removal showed an increasing trend with an increased coagulant dose, reaching the plateau value under large coagulant dose conditions for both Ti- and Al-based coagulants regardless of B value. The chemical dose of Ti-based coagulants was approximately twice higher than that of Al-based coagulants with the same P-removal efficiency. The coagulation efficiency was influenced by different B values.