• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.1038-1046
• /
• 2014

Lithium-ion batteries are widely used in hybrid and pure electric vehicles. State-of-charge (SOC) estimation is a fundamental issue in vehicle power train control and battery management systems. This study proposes a novel model-based SOC estimation method that applies closed-loop state observer theory and a comprehensive battery model. The state-space model of lithium-ion battery is developed based on a three-order resistor-capacitor equivalent circuit model. The least square algorithm is used to identify model parameters. A multi-state closed-loop state observer is designed to predict the open-circuit voltage (OCV) of a battery based on the battery state-space model. Battery SOC can then be estimated based on the corresponding relationship between battery OCV and SOC. Finally, practical driving tests that use two types of typical driving cycle are performed to verify the proposed SOC estimation method. Test results prove that the proposed estimation method is reasonably accurate and exhibits accuracy in estimating SOC within 2% under different driving cycles.

• Journal of Hydrogen and New Energy
• /
• v.27 no.2
• /
• pp.144-154
• /
• 2016

HT-PEMFC (high temperature polymer electrolyte membrane fuel cell) using PA (phosphoric acid) doped PBI (polybenzimidazole) membrane has been researched for extending the lifetime. However, the existing work on durability of HT-PEMFC focuses on identifying degradation causes of lab scale. The short life time of HT-PEMFC is still the problem for its commercialization. In this paper, an operating method to maximize life time of 5kW HT-PEMFC stack are proposed. The proposed method includes major steps such as minimization of OCV (Open Circuit Voltage) exposure, control of the proper stack temperature, and N2 purging for the stack. This long life operating method was based on the fragmentary results of degradation from previous research works. Experimentally, the 5 kW homemade HT-PEMFC stack was operated for a long time based on the proposed method and the stack successfully can operate within the desired degradation rate for the target life time.

• Journal of Hydrogen and New Energy
• /
• v.21 no.5
• /
• pp.419-424
• /
• 2010

The 125kW external reforming (ER) type molten carbonate fuel cell (MCFC) system for developing a commercial prototype has been operated at Boryeong thermal power plant site since the end of 2009. The system consists of 125kW stack with $10,000 cm^2$ effective area, mechanical balance of plant (MBOP) with anode recycle system, and electrical balance of plant (EBOP). The 125kW MCFC stack installed in December, 2009 has been operated from January, 2010 after 20 days pre-treatment. The stack open circuit voltage (OCV) was 214V at initial load operation, which approaches the thermodynamically theoretical voltage. The stack voltage remained stable range from 160V to 180V at the maximum generating power of 120 kW DC. The stack has been operated for 3,270 hours and operated at rated power for 1,200 hours.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.27-37
• /
• 2016

In this paper, a mixed algorithm is proposed to overcome the limitations of the conventional algorithms, which cannot be applied in various driving patterns of drivers. The proposed algorithm based on the coulomb counting method is mixed with reset algorithms that consist of the enhanced OCV reset method and the DCIR iterative calculation method. It has many advantages, such as a simple model structure, low computational overload in various profiles, and a low accumulated SOC error through the frequent SOC reset. In addition, the enhanced parameter based on a mathematical analysis of the second-order RC ladder model is calculated and is then applied to all of the methods. The proposed algorithm is verified by experimental results based on a 27-Ah LiPB. It is observed that the SOC RMSE of the proposed algorithm decreases by about 9.16% compared to the coulomb counting method.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.333-336
• /
• 2013

Experimental investigation to estimate the feasibility of fast selective catalytic reduction (SCR) or oxidation catalyst combined ammonia SCR system to abate NOx in low temperature condition ($150{\sim}250^{\circ}C$) is reported. Because the conversion of NO to $NO_2$ is pre-requisite of the fast SCR process, the effect of the amount of oxidation catalyst to NO conversion to $NO_2$ was tested. 37, 45 and 51% of conversion rates were obtained for the OCV of 563000, 375000 and 281000 h, respectively. $De-NO_x$ performance in the case of $NO_2/NO_x$ ratio of 45% showed the best result in all tested temperature conditions. Comparison of the fast SCR and standard SCR with the condition of $NO_2/NO_x$ ratio of 45%, $200{\sim}250^{\circ}C$ and space velocity of 10000~30000 h showed that the fast SCR does not show much difference according to the variance of space velocity. Also it was shown that using the fast SCR, the volume of SCR catalyst can be reduced less than half of the standard SCR condition by increasing space velocity without the loss of $De-NO_x$ performance.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.313-314
• /
• 2016

본 논문에서는 리튬이온(Li-Ion) 배터리 셀(Cell)의 Shock test와 Vibration test 기반 18650 원통형 셀 내부 전기적 특성 변화를 분석하였다. 전류적산법을 기반으로 방전 용량을 측정하였고, OCV(Open Circuit Voltage) 측정 및 HPPC(Hybrid Pulse Power Characterization) test를 기반으로 내부 저항을 측정하고 진동 및 충격 시험 전 후의 파라미터를 비교 분석하였다.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.375-376
• /
• 2016

본 논문에서는 Li-air 배터리의 동작원리를 설명하고, 모델링을 위해 Li-air 배터리의 내부와 충전 및 방전 원리를 보여주고 SOC(State Of Charge) 추정을 위한 OCV(Open-circuit Voltage) 그래프의 분석과 회로도에 대해 설명 하였다. 더불어, 전류적산법의 원리를 적용하여 SOC 추정의 기준이 되는 값을 추출하였다.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.198-199
• /
• 2013

본 논문에서는 리튬공기(Li-Air) 배터리를 소개하고 전기화학적 특성분석을 간단히 진행하였다. 우선, 리튬공기 배터리의 동작원리를 소개하고 기존 리튬이온(Li-Ion) 배터리와의 차이점을 제시하였다. 각 만방전압에 따른 배터리의 전기화학적 특성분석을 위해 방전용량 및 임피던스 특성커브를 분석하였다. 더불어, 향후 State-of-charge(SOC) 추정을 위한 데이터를 위해 Open-circuit voltage(OCV) 및 실제 충방전 전류 프로파일에 따른 충방전 전압을 분석하였다.

• Journal of the Korean Chemical Society
• /
• v.41 no.9
• /
• pp.488-494
• /
• 1997

Lithium and sodium ions have been intercalated into two dimensional structure of $FeMoO_4Cl$. The electronic localization and the large difference in unit cell parameter between the pristine material and the intercalates lead to the existence of large biphased domains. In the case of the lithium system, a narrow range of $Li_xFeMoO_4Cl$ ($0.95{\leq}x{\leq}1.06$) solid solution has been found around the $LiFeMoO_4Cl$ composition. The OCV curve fitting has been performed using Armand's model. The occurrence of several parts in the charge-discharge curve is related to the electronic and structural modifications of the material during the intercalation process.

• Korean Chemical Engineering Research
• /
• v.58 no.4
• /
• pp.524-529
• /
• 2020

To increase the mechanical durability of the proton exchange membrane fuel cells, a reinforced membrane in which a support is placed in the polymer membrane is used. The support mainly uses e-PTFE, which is hydrophobic and does not transfer ions, which may cause performance degradation. In this study, we investigated the effect of e-PTFE support on PEMFC performance and electrochemical durability. In this study, the reinforced membrane with the support was compared with the single membrane (non-reinforced membrane). Due to the hydrophobicity of the support, the water diffusion coefficient of the reinforced membrane was lower than that of the single membrane. The reinforced membrane had a lower water diffusion coefficient, resulting in higher HFR, which is the membrane migration resistance of ions, than that of a single membrane. Due to the low hydrogen permeability of the support, the OCV of the reinforced membrane was higher than that of the single membrane. The support was shown to reduce the hydrogen permeability, thereby reducing the rate of radical generation, thereby improving the electrochemical durability of the reinforced membrane.