• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.1
• /
• pp.12-17
• /
• 1998

The heteroepitaxial growth of InP and GaInAs on GaAs substrates has been studied by using a new combination of source materials: ethyldimethylindium (EDMIn) and trimethylgallium (TMGa) as group III sources, and tertiarybutylarsine (TBAs) and tertiarybutylphosphine (TBP) as group V sources. Device quality InP heteroepitaxial layers were obtained by using a two-step growth process under atmospheric pressure, involving a growth of an initial nucleation layer at low temperature followed by high temperature annealing and the deposition of epitaxial layer at a growth temperature. The continuity and thickness of nucleation layer were important parameters. The InP layers deposited at 500$^{\circ}$- 55$0^{\circ}C$ are all n-type, and the electron concentration decreases with decreasing TBP/EDMIn molar ratio. The excellent optical quality was revealed by the 4.4 K photoluminescence (PL) measurement with the full width at half maximum (FWHM) of 4.94 meV. Epitaxial Ga\ulcorner\ulcorner\ulcornerIn\ulcorner\ulcorner\ulcornerAs layers have been deposited on GaAs substrates at 500$^{\circ}$ - 55$0^{\circ}C$ by using InP buffer layers. The composition of GaInAs was determined by optical absorption measurements.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.16 no.1
• /
• pp.22-29
• /
• 2008

A sequence of visually experimental observations was conducted to investigate the flow boiling and two-phase flow in a coiled tube. Different boiling modes and bubble dynamical evolutions were identified for better recognizing the phenomena and understanding the two-phase flow evolution and heat transfer mechanisms. The dissolved gases and remained vapor would serve as foreign nucleation sites, and together with the effect of buoyancy, centrifugal force and liquid flow, these also induce very different flow boiling nucleation, boiling modes, bubble dynamical behavior, and further the boiling heat transfer performance. Bubbly flow, plug flow, slug flow, stratified/wavy flow and annular flow were observed during the boiling process in the coiled tube. Particularly the effects of flow reconstructing and thermal non-equilibrium release in the bends were noted and discussed with the physical understanding. Coupled with the effects of the buoyancy, centrifugal force and inertia or momentum ratio of the two fluids, the flow reconstructing and thermal non-equilibrium release effects have critical importance for flow pattern in the bends and flow evolution in next straight sections.

• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.462-468
• /
• 2010

Carbon Nanotubes (CNTs) have recently emerged as a material with outstanding properties. It has shown promising potential for applications in many engineering fields as electronic devices, thermal conductors, and light-weight composites. Researchers have investigated their use as reinforcements in themetal matrix composites of CNTs. In the present work, we decorated CNTs with Ni particles by electroless plating. The CNTs were wet-ball milled for various milling times with a nickel sulfate solution. The precipitated Ni particles were observed mainly by FESEM. In this study, the dispersion of the CNTs and Ni particles was improved with the addition of the surfactant. Also, as the CNTs were shortened and widened by an increased ball milling time, the size of the precipitated Ni particles increased. It was estimated that the CNTs were deformed and caused some defects on their surface during the ball milling process. Those defects were assumed to be heterogeneous nucleation sites for the Ni particles.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.412-414
• /
• 2004

We have developed nucleation control methods applicable to a zone-melting recrystallization excimer laser annealing process for poly-Si films. Ribbon-shaped Si grains of 2 ${\mu}m$-width were successfully aligned side by side by means of a comb-shaped beam, and we have successfully fabricated TFTs with channels formed in those grains. Electron mobility in the TFTs is as high as 677-$cm^2$/Vs.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1492-1494
• /
• 1996

We have studied the generation, growth and behavior of chemical species and particles in silane PCVD. We included the plasma chemistry of silane, particle nucleation by homogeneous formation, acrosol dynamics and transport phenomena of chemical species and particles. The concentration profile of chemical species and particles were shown as a function of reactor length. The effects of process variables such as reactor pressure, total gas flow rate and electrical field strength on the behavior of chemical species and particles were analyzed.

• Resources Recycling
• /
• v.24 no.4
• /
• pp.22-31
• /
• 2015

From results obtained by adjusting experimental variables based on the kinetic, the nucleation rate for formation of precipitated calcium carbonate (PCC) was investigated. Formation behavior of PCC was investigated for various concentrations of NaOH solution and $Na_2CO_3$ addition methods in the $Ca(OH)_2$ slurry. The range of nucleation rate was investigated for dissolution rates of major ion concentrations, $Ca^{2+}$ and $CO{_3}^{2-}$. In case of high concentration of major ions, vaterite and calcite were synthesized. The high nucleation rate was achieved for lower either $Ca^{2+}$ or $CO{_3}^{2-}$ ion concentration, calcite was mainly synthesized and when concentration of major ions was low, aragonite was synthesized. Furthermore, the formation of calcite was decreased with increasing concentration of NaOH. homogeneous aragonite could be obtained by addition 5 M NaOH. Therefore, in this study, specific shape of polymorphs could be prepared through controlling supersaturation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.4
• /
• pp.160-164
• /
• 2007

Carbon nanofibers were deposited on silicon oxide substrate by thermal chemical vapor deposition method. For the enhancement of the characteristics of carbon nanofibers, the source gases ($C_2H_2,\;H_2$) flows were intentionally manipulated as the cyclic on/off modulation of $C_2H_2$ flow. By the cyclic modulation process during the initial deposition stage, the formation density of carbon nanofibers on the substrate could be much more enhanced. The diameter of as-grown carbon nanofibers was also reduced by the cyclic modulation process. The cause for the variation in the characteristics of carbon nanofibers by the cyclic modulation process was discussed in association with the hydrogen gas etching ability.

• Korean Journal of Crystallography
• /
• v.3 no.1
• /
• pp.53-66
• /
• 1992

Extensive research has been perform성 on the property-microstructure-process condition relations of thin films. The various proposed models are mainly based on physical vapor deposition processes. Especially the study on the surface condition of substrates in Zone 1 with low surface mobility has not been sufficient. In this study, therefore, we discussed the mochological changes of TiN films deposited by plusma enhanced chemical vapor deposition process with substrates of different composition and micro-rorghness, and compared it with the Structure Zone Model. We could find out that the growth rate of films increased and micro-grain size decreased with the increase in micro-roughness, but it does not improve the mechanical properties because of many imperfections like voids, micro-cracks, stacking faults, etc. This means that, in these deposition conditions, the increase in shadowing diffect is more effective than the increase in nucleation sites on the growth of films due to the increase in substrate roughness.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.127-134
• /
• 2002

Microporous polypropylene hollow fiber membrane was fabricated from isotactic polypropylene-soybean oil system by melt spinning process. Addition of nucleating agent accelerated the crystallization rate and elevated the crystallization temperature. Nucleating agent increased the number of nuclei and spherulites, which offered more inter-spherulitic amorphous sites for stretching. Benzoic acid, adipic acid, and dibenzylidene sorbitol were selected as nucleating agents, and their characteristics and effects were investigated by thermal and optical analyses. Spherulite growth and micropore formation characteristics were correlated with the kind of nucleating agent. Benzoic acid and adipic acid showed the remarkable nucleating effect, while dibenzylidene sorbitol was less effective than those. Nucleating agents also helped the sample have uniform microporous structure. Increase of nucleating agent composition enhanced the nucleation effect to some extent. Nucleating agents played very important roles in enhancing the membrane porosity and water flux.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.104-109
• /
• 2011

Bulk metallic glasses (BMG) have been greatly improved by the advance of synthesis process during last three decades. It was also found that the Glass Forming Ability (GFA) strongly depends on the glass transition temperature. When the temperature approaches to a critical value, the crystals nucleation from the supercooled liquid can be suppressed so that bulk glass formation possible. Egami and others found that the local glass transition temperature depends on the volumetric strain of each atom and suggested the critical transition temperature. In this paper, we explore the strain dependency of local glass transition temperature using the atomic strain defined by the deformation tensor for the Voronoi polyhedra.