• 한국산학기술학회논문지
• /
• 제7권5호
• /
• pp.759-765
• /
• 2006

유기발광다이오드(OLED)증착을 위한 서큘러소스의 열전달 해석을 통하여 온도분포를 연구하였다. 대면적의 OLED용 평판의 유기물증착을 위해 서큘러소스가 사용되는데, 소스내의 유기물이 가열되고, 승화되어 증착된다. 유기물의 수율을 높이기 위해 히터설계를 개선하고, 이에 대한 열전달해석을 수행하였다. 그리고, 효율을 높이기 위한 새로운 제조공정인 OVPD공정의 개념과 유도 및 열전달특성에 관한 기본적인 연구결과를 제시하였다.

• 한국정밀공학회지
• /
• 제27권6호
• /
• pp.55-63
• /
• 2010

Feedwater heaters of many nuclear power plants have recently experienced severe wall thinning damage, which will increase as operating time progresses. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle inside feedwater heater installed downstream of the turbine extraction stream line. At that point, the extract steam from the turbine is two phase fluid at high temperature, high pressure, and high speed. Since it flows to reverse direction after impinging the impingement baffle, the shell wall of feedwater heaters may be affected by flow-accelerated corrosion. In this paper, to compare degree of shell wall thinning mitigation rate to squared type with mitigation rate of other type baffle plate, three different types of impingement baffle plate-squared, curved and mitigating type-applied inside the shell. With these comparison data, this paper describes operation of experiments and numerical analysis which is composed similar condition with real feed water heater. And flow visualization is operated for verification of experiments and numerical analysis. In conclusion, this study shows that mitigating type baffle plate is more effective than other baffle plate about prevention of pressure concentration and pressure value decrease.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.86-93
• /
• 1996

The lubrication characteristics of high-speed ball bearings has been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flowrates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 303 kgf axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.786-789
• /
• 2005

The proper parameters in a twin roll strip casting are important to obtain the stabilization of the Mg sheet. What is examined in this paper is the quantitative relationships of the important control parameters such as the roll speed, height of pool region, outlet size of nozzle, solidification profile and the final point of solidification in a twin roll strip casting Unsteady conservation equations were used for transport phenomena in the pool region of a twin roll strip casting in order to predict a velocity, temperature distributions of fields and a solidification process of molten magnesium. The energy equation of cooling roll Is solved simultaneously with the conservation equations of molten magnesium In order to consider the heat transfer through the cooling roil. The finite difference method (2-D) and the finite element method (2-D) are used in the analysis of pool region and cooling roil to reduce computing time and to improve the accuracy of calculation respectively.

• 대한기계학회논문집B
• /
• 제22권2호
• /
• pp.193-204
• /
• 1998

Numerical analysis was performed with multicomponent transport properties and detailed reaction mechanisms for axisymmetric 2-D CH$_{4}$ jet diffusion flame. Calculations were carried out twice with the $C_{2}$-Thermal Mechanism including $C_{2}$ and thermal NO reactions and the $C_{2}$-Full Mechanism including prompt NO reactions in addition to the above $C_{2}$-Thermal NO mechanism. The results show that the flame structures such as flame temperature, major and minor species concentration are indifferent to respective mechanisms. The production path of Thermal NO is dominant comparing with that of Prompt NO in total NO production of pure CH$_{4}$ jet diffusion flame. This is because thermal NO mechanism mainly contributes to positive formation of NO in the whole flame region, but Prompt NO mechanism contributes to negative formation in the fuel rich region. In addition, 0$_{2}$ penetration near the nozzle outlet affects the flame structures, especially N0$_{2}$ formation characteristics.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.36-40
• /
• 2008

마이크로 추진장치에서 노즐의 소형화는 많은 유동손실을 유발한다. 이러한 유동손실을 극복하기 위해 본 연구에서는 열적발산원리를 이용한 새로운 개념의 마이크로 추진장치에 대한 기초연구를 진행하였다. 움직이는 부품 없이 오직 온도구배만으로 추진제를 낮은 온도에서 높은 온도로 자체 펌핑이 가능한 열적발산장치를 설계, 제작 하였으며, 진공환경에서 누센수에 따른 멤브레인 압력구배효율을 분석하였다. 또한 기존 누센펌프의 멤브레인인 폴리이미드와 종이재질의 전통 한지를 사용하여 질유량 특성을 비교하였다.

• 설비공학논문집
• /
• 제20권1호
• /
• pp.75-80
• /
• 2008

The objective of this research was to investigate the enhancement of heat transfer by mesh in water/air direct contact air conditioning system. Mesh is inserted as a turbulent promoter in front of the water injection nozzle. The heat transfer characteristics with and without mesh and the effect of the number of inserted mesh and mesh porosity size have been studied experimentally. Inserted mesh improves heat transfer efficiency compared to non~inserted mesh system and heat transfer efficiency increased as the number of mesh is increased. Meanwhile, heat transfer efficiency decreased as the porosity of the mesh is increased. With inserted mesh, inlet and outlet temperature difference of air increased more than 50%. Heat exchange time of water/air to reach the 100% humidity decreased less than 30%. This result shows inserted mesh can enhance the performance of the water/air direct contact air conditioning system.

• 사물인터넷융복합논문지
• /
• 제7권3호
• /
• pp.75-80
• /
• 2021

NOx의 배출저감 방법으로 선박용 디젤엔진의 최적화만으로는 배기가스의 NOx 배출량 제한을 만족시킬 수 없기 때문에 반드시 배기가스를 후처리하여 NOx를 저감할 수 있는 방안이 요구된다. 본 연구에서는 현재 개발 중에 있는 선박용 SCR 촉매 유닛 일체형 덕트용 오일 버너 시스템에서 요소수를 NH3로 효과적으로 변환하기 위한 이류체 노즐과 믹싱 챔버 덕트에 관한 설계 타당성 여부를 속도분포 및 온도분포에 대한 전산열유동 해석을 통해 검토하고자 한다.

• 한국추진공학회지
• /
• 제24권6호
• /
• pp.45-52
• /
• 2020

초소형 스마트탄의 개발을 위해 초소형 추진기관을 설계하고 그레인은 내부 형상의 제작 용이성을 고려하여 열가소성 추진제로 제작하였다. 추진기관의 성능분석을 위해 지상연소시험과 내탄도 해석이 수행되었다. 그리고 사수와 추진기관 간 안전거리 설계에 대한 기초자료를 획득하기 위하여 수치해석을 수행하였으며, 배기가스의 온도분포는 수치해석과 IR 카메라의 측정결과를 비교하여 분석되었다.

• International Journal of Advanced Culture Technology
• /
• 제10권3호
• /
• pp.295-306
• /
• 2022

The NOx removal performance of the SCR process depends on various factors such as catalytic factors (catalyst composition, shape, space velocity, etc.), temperature and flow rate distribution of the exhaust gas. Among them, the uniformity of the flow flowing into the catalyst bed plays the most important role. In this study, the flow characteristics in the SCR reactor in the design stage were simulated using a three-dimensional numerical analysis technique to confirm the uniformity of the airflow. Due to the limitation of the installation space, the shape of the inlet duct was compared with the two types of inlet duct shape because there were many curved sections of the inlet duct and the duct size margin was not large. The effect of inlet duct shape, guide vane or mixer installation, and venturi shape change on SCR reactor internal flow, airflow uniformity, and space utilization rate of ammonia concentration were studied. It was found that the uniformity of the airflow reaching the catalyst layer was greatly improved when an inlet duct with a shape that could suppress drift was applied and guide vanes were installed in the curved part of the inlet duct to properly distribute the process gas. In addition, the space utilization rate was greatly improved when the duct at the rear of the nozzle was applied as a venturi type rather than a mixer for uniform distribution of ammonia gas.