• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.3
• /
• pp.41-47
• /
• 2013

This study was carried out to improve the design of fuel injection nozzle for marine medium speed diesel engine. For this purpose, fuel injection nozzle was modeled and simulated using CATIA V5R19 and FLUENT & MSC Nastran. Analyses of flow and heat transfer, respectively, were performed to find the optimal design of fuel injection nozzle. As the results, big pressure drop, which may lead to cavitation damage, was occurred at inlet of fuel injection hole with diameter 0.3mm. Furthermore, it was confirmed that the increase of mean temperature of fuel injection nozzle was almost a half in comparison with that of fuel injection nozzle tip.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.1
• /
• pp.73-79
• /
• 2011

Inkjet printhead may have a lot of nozzles to increase productivity as a manufacturing tool. So, the uniformity of jetting performance among a lot of nozzles has been one of the key issues in inkjet technology In this study, we investigated the cross-talk effect which should be reduced for uniform jetting performance among a lot of nozzles. Due to the cross-talk, the jetting performance of a nozzle can be affected when neighboring nozzles are firing. For experimental study, we used commercial inkjet head SE-128 from Dimatix. To understand the cross-talk effect of SE-128 head, we measured the change in jetting speed of a nozzle when neighboring nozzles are jetting. The measured jetting speed was compared to the case of one nozzle jetting. Also, we used laser vibrometer to measure change in pressure wave due to cross-talk. As a result of the cross-talk, the jetting speed can become faster or sometimes slower depending on firing nozzle location. If the all nozzle are jetting, the jetting speed of a nozzle became slower because the pressure wave for jetting is reduced.

• Fashion & Textile Research Journal
• /
• v.1 no.2
• /
• pp.166-172
• /
• 1999

An experimental investigation has done for studying the changes of physical properties of the air-jet textured polyester yarn. Through the experiments of polyester 85/72 drawn yarn and 50/36 partially oriented yarn doubling' the following results are obtained. The tenacity of textured yarn decreased as the number of tension rings increased when the nozzle diameter was 1.2 mm. In the case when the tension ring was not used during the texturing process, the tenacity of textured yarn decreased as the nozzle diameter increased. But this tendency changed according to the number of tension rings used, the diameter of the nozzle, and yarn take-up speed. Breaking elongation decreased as the number of tension rings increased from one to four and the take-up speed increased at diameter 1.2 mm of the nozzle. The higher the diameter of the the nozzle the higher the breaking elongation until 1.4 mm. The number of interlacing went down as the diameter of the nozzle increased and the take-up speed of the yarn increased. The higher the number of tension rings, the lower the number of interlacing.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.37-44
• /
• 1993

Fuel injection system is an important tool in the exhaust emission and performance of a diesel engine. Effects of the fuel injection system in diesel combustion was investigated experimentally by measuring the performance and analyzing the combustion phenomena in a D.I. diesel engine. The selected injection parameters were nozzle opening pressure, nozzle projection length, and nozzle spray angle. From the measured results, it is shown that the fuel injection pipe diameter is an effective means to improve engine performance in a middle and high speed range and the 2 stage spring nozzle holder has the advantage of increasing the engine performance due to the initial injection pressure in a low speed range. It has been also shown that increasing nozzle opening pressure resulted in decrease in smoke, but increase in NO$_{x}$ from the engine.e.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.5
• /
• pp.262-269
• /
• 2022

In order to process materials such as engineering plastics, which are difficult to mold due to their high strength compared to conventional polymer materials, it is necessary to improve the hardness and strength of parts such as screws and barrels of injection equipment in extrusion system. High-velocity oxygen fuel (HVOF) process is well known for its contribution on enhancement of surface properties. Thus in this study, using the HVOF process, WC coating layers of different thicknesses were bonded to the surface of S30C substrate by controlling the movement speed of the spray nozzle and each property was evaluated to decide the optimization condition. Through the results, the thickness of WC coating layer increased from 0 to 200 ㎛ maximum, along with the decrement of nozzle movement speed and the surface hardness get increased. Especially, the coated layer with the thickness over 180 ㎛ under the nozzle speed 500 mm/s had high hardness than thinner layer. In addition, the amount of wear consumed per unit time was also significantly reduced due to the formation of the coating layer.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.5
• /
• pp.34-40
• /
• 2003

This paper presents the inertial force problem of ultrahigh-speed injection molding machine using linear motors, and presents its solutions. To make very thin products by injection molding, very high injection speed is required, and linear motors are used for this purpose. However, direct drive by linear motors may cause brief nozzle separation from the sprue bushing because of the inertia force which is as large as the total output thrust of the linear motors, and this momentary separation can cause molten plastic to leak. In this paper, two solutions are proposed for this inertia force problem. One is the mechanical cancellation of the inertia force, and the other is to increase the nozzle contact force. With the latter solution, the stationary platen bending worsens, so a new nozzle contact mechanism is also proposed, which can prevent the stationary platen bending.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.171-177
• /
• 2002

This paper presents the inertial force problem of ultrahigh-speed injection molding machine using linear motors, and presents its solutions. To make very thin products by injection molding, very high injection speed is required, and linear motors are used for this purpose. But direct drive by linear motors may cause brief nozzle separation from the sprue bushing because of the inertia force as large as the total output thrust of the linear motors, and this momentary separation can cause molten plastic leakage. In this paper, two solutions are proposed for this inertia force problem. One is the mechanical cancellation of the inertia force, and the other to increase the nozzle contact force. With the latter solution, the stationary platen bending worsens, so a new nozzle contact mechanism is also proposed, which can prevent the stationary platen bending.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.6
• /
• pp.662-668
• /
• 2006

The effects of fuel injection nozzle hole on the NOx emission and fuel oil consumption of medium speed diesel engine HYUNDAI HiMSEN 6H21/32 engine are investigated by engine performance simulation. The results of performance simulation are verified by experimental results of NOx omission fuel oil consumption, cylinder pressure, and heat release rate according to the variation of the number of fuel injection nozzle hole and engine load. The performance simulations are also carried out to optimize the fuel injection nozzle of 6H21/32 engine in respect to the NOx emission and fuel oil consumption. The engine performance measurements are performed to verify the results of performance simulation and to investigate the effects of fuel injection nozzle on engine performance. The results of measurement indicate that significant NOx reduction can be achieved with minimum deterioration in fuel oil consumption by optimizing the geometry of fuel injection nozzle on 6H21/32 engine.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.220-226
• /
• 2006

The effect of electric fields on the propagation speed of tribrachial flames has been investigated in a coflow jet by observing the transient flame propagation behavior after ignition. Without having electric fields, the propagation speed of tribrachial flame edges showed a typical behavior by having an inverse proportionality to the mixture fraction gradient at the flame edge. The behavior of flame propagation with the electric fields was investigated by applying high voltage to the central fuel nozzle and the enhancement of propagation speed has been observed by varying the applied voltage and frequency for AC electric fields. The propagation speed of tribrachial flame was also investigated by applying negative and positive DC voltages to the nozzle and similar improvements of the propagation speed were also observed. The propagation speeds of tribrachial flames in both the AC and DC electric fields were correlated well with the electric field intensity, defined by the electric voltage divided by the distance between the nozzle electrode and the edge of tribrachial flames.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.4 s.247
• /
• pp.306-313
• /
• 2006

Automated material handling system is being used as a method to reduce manufacturing cost in the semiconductor and flat panel displays (FPDs) manufacturing process. Those are considering switch-over from the traditional cassette system to single-substrate transfer system to reduce raw materials of stocks in the processing line. In the present study, the wafer transportation speed has been evaluated by numerical and experimental method for three propulsion nozzle array (face, front, rear) in an air levitation system. Test facility for 300 mm wafer was equipped with two control tracks and a transfer track of 1,500mm length. The diameter of propulsion nozzle is 0.8mm and air velocity of wafer propulsion is $50\sim150m/s$. We found that the experimental results of the wafer transportation speed were well agreed with the numerical ones. Namely, the predicted values of the maximum wafer transportation speed are higher than those values of experimental data by 16% and the numerical result of the mean wafer transportation speed is higher than the experimental result within 20%.