• 대한기계학회논문집B
• /
• 제20권2호
• /
• pp.697-709
• /
• 1996

Supersonic axisymmetric jets issuing from various kinds of nozzles with a throat diameter of a few millimeters were experimentally investigated. The exit Mach number and Reynolds number based on the throat diameter of nozzle were in the range of 1.0 ~ 5.9 and 8.4$\times$ $10^4$ ~ 2.9$\times$$10^6$, respectively. The nozzle pressure ratio was varied from 5 to 85. Present paper aims to offer fundamental information of the supersonic free-jets, with an emphasis to give data with which the shape of the free-jets can be depicted under a specified condition. Experimental data are summarized to enable an estimation of the shape of the supersonic free-jets. The result shows that the shape of free-jets is dependent on only the nozzle pressure ratio.

• 한국분무공학회지
• /
• 제24권3호
• /
• pp.105-113
• /
• 2019

In this paper, a study of Urea-SCR System for Dosing Injector for responding to enhanced environmental regulations has been conducted. There is a limit to the experimental approach due to the structural characteristics of the injector. In order to overcome this problem, The analysis was performed assuming unsteady turbulent flow through computational fluid analysis and the internal flow characteristics of the injector were analyzed. By changing the nozzle shape of the injector, the performance factors of the swirl injector by shape were selected and compared. The design parameters were modified by changing the diameter of the nozzle at a constant ratio compared to the base model. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. The Conv. model to which the taper was applied showed the dominance in mass flow rate, discharge coefficient and swirl because of the smooth fluid flow by shape. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. As a result of the comparison coefficient derivation with those performance parameters for comparing the performance of the model-specific injector, the Conv-140 model with the nozzle diameter expanded by 140% showed the best value of the comparison coefficient.

• 한국추진공학회지
• /
• 제12권2호
• /
• pp.8-14
• /
• 2008

고체 추진기관은 높은 비추력, 운용 안전성, 설계/제작하기가 쉽다는 장점이 있으나 추력 크기를 조절할 수 없다. 본 논문에서는 고체 추진기관의 추력을 조절할 수 있는 핀틀 노즐성능에 대한 연구로 Needle형 핀틀을 사용하여 수행한 공압 시험결과와 수치해석 결과를 수록하였다. 연구의 결과, 핀틀 노즐의 추력성능과 추력변화 범위는 핀틀 팁의 형상과 노즐의 Contour형상에 크게 의존하기 때문에 핀틀 팁의 형상과 노즐의 Contour형상은 중요한 설계 변수임을 알 수 있었고 특히, 시험에 적용된 Needle형 핀틀 노즐의 성능은 기존 노즐 대비 약 13%의 추력상승이 예측됨을 알 수 있었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 춘계 학술대회논문집
• /
• pp.168-173
• /
• 1998

A numerical analysis of axisymetric backward facing step main nozzle flow in air jet loom has been accomplished. To obtain basic design data for an optimum main nozzle for an air-jet loom and to predict the transonic/supersonic flow, a characteristic based upwind flux difference splitting compressible Navier-Stokes method has been used. The wall static pressure of the main nozzle and the flow velocity changes in the nozzle tube were analyzed by changing air tank pressures and acceleration tube lengths. The flow inside the nozzle experiences double choking one at the needle tip and the other at the acceleration tube exit at tank pressures over $4kg_f/cm^2$. The tank pressure $P_t$ leading to the critical condition depends on the acceleration tube length; i.e, $P_t$ is higher for longer acceleration tubes. The $P_t$ value required to bring the acceleration tube exit to the critical condition is nearly constant regardless of acceleration tube length. The round needle tip shape might lead to less total pressure loss when compared with step shape.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.289-294
• /
• 2007

고체 추진기관은 높은 비추력, 운용 안전성, 설계/제작하기가 쉽다는 장점이 있으나 추력 크기를 조절할 수 없다. 본 논문에서는 고체 추진기관의 추력을 조절할 수 있는 핀틀 노즐성능에 대한 연구로 Needle형 핀틀을 사용하여 수행한 공압 시험결과와 수치해석 결과를 수록하였다. 연구의 결과, 핀틀 노즐의 추력성능과 추력변화 범위는 핀틀 팁의 형상과 노즐의 Contour형상에 크게 의존하기 때문에 핀틀 팁의 형상과 노즐의 Contour형상은 중요한 설계 변수임을 알 수 있었고 특히, 시험에 적용된 Needle형 핀틀 노즐의 성능은 기존 노즐 대비 약 13%의 추력상승이 예측됨을 알 수 있었다.

• Nuclear Engineering and Technology
• /
• 제52권11호
• /
• pp.2638-2651
• /
• 2020

Nozzle corner cracks present at the intersection of reactor pressure vessels (RPVs) and inlet or outlet nozzles have been a persistent problem for a number of years. The fracture analysis of such nozzle corner cracks is very important and critical for the efficient design and assessment of the structural integrity of RPVs. This paper aims to perform an engineering critical assessment of RPVs with nozzle corner cracks subjected to several transients accompanied by pressurized thermal shocks. The critical crack size of the RPV model with nozzle corner cracks under transient loading is evaluated on failure assessment curve. In particular, the influence of cladding on the crack initiation of nozzle corner crack under thermal transients is studied. The influence of primary internal pressure and secondary thermal stress on the stress field at nozzle corner and SIF at crack front is analyzed. Finally, the influence of different crack size and crack shape on the final critical crack size is analyzed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.297-305
• /
• 2006

본 논문에서는 터빈의 형상 변수에 따른 부분흡입형 초음속 터빈 손실 특성을 분석하기 위하여 초음속 노즐 형상, 축방향 간극 길이, 로터 앞전의 모서리각에 따른 초음속 터빈내 유동 해석을 실시하였다. 먼저 축방향 간극을 진행하면서 발생하는 유동의 익렬 팁방향의 휘어짐은 초음속 노즐 형상에 크게 영향을 받는다. 다음으로 모서리각은 익렬 앞전에서 발생하는 충격파등의 강도를 결정한다. 마지막으로 축방향 간극에서 발생하는 유동의 확산 및 혼합은 축방향 간극 길이에 크게 영향을 받았다. 따라서 터빈내에서 발생하는 손실 중 유체역학적 손실은 노즐 형상과 로터 앞전의 모서리각에 의해 결정되었으며, 부분 흡입 손실은 노즐 형상 및 축방향 간극 길이에 영향을 받았다.

• 한국분무공학회지
• /
• 제26권1호
• /
• pp.33-39
• /
• 2021

Y-jet nozzle has a wide fuel flow rate range and turn-down ratio, thus, it is used in industrial boilers, furnace and agricultural atomizer. However, it has asymmetrical spray characteristics due to the nozzle design factors. Therefore, in this study, asymmetric spraying characteristics of the elliptical Y-jet nozzle was studied by using the lab-scale spray apparatus. As a result, the elliptical Y-jet nozzle had lower gas mass flow rate than circular Y-jet nozzle at same gas pressure, because of bigger shear stress due to the wider inner surface at the elliptical Y-jet nozzle. Larger SMD was measured on the elliptical Y-jet nozzle than the circular Y-jet nozzle. When SMD was measured in the X_Axis direction at the same gas mass flow rate, the elliptical Y-jet nozzle with an aspect ratio of 2:1 showed greater asymmetry than the others.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.221-230
• /
• 2011

The cold spray process is an emerging technology that utilizes high velocity metallic particles for surface coating. Metallic powder particles are injected into a converging-diverging de Laval nozzle and accelerated to a high velocity by a supersonic gas flow. The cold spray process normally uses a circular nozzle that has a rather narrow spraying range. To overcome this fault, a slit nozzle was considered in this study. The slit nozzle is anticipated to reduce the coating process time because it has a wider coating width than the circular nozzle. However, the slit nozzle can reduce the coating efficiency because it does not allow as much gas and particle velocity as the circular nozzle. To improve the coating efficiency of a slit nozzle, the shape of the slit nozzle was modified. And the results of gas flow and particle behaviour according to the nozzlers shape were compared by the a numerical analysis. As a results, as Expansion Ratio(ER) of 7.5 was found to be the most optimal condition for enhancing the spraying efficiency when the ER was changed by the variation of nozzle neck and exit size.

• Advances in aircraft and spacecraft science
• /
• 제7권3호
• /
• pp.187-202
• /
• 2020

The exhaust nozzle serves back pressure of Pulse detonation combustor, so combustion chamber gets sufficient pressure for propulsion. In this context recent researches are focused on influence of nozzle effect on single cycle detonation wave propagation and propulsion performance of PDE. The effects of various nozzles like convergent-divergent nozzle, convergent nozzle, divergent nozzle and without nozzle at exit section of detonation tubes were computationally investigated to seek the desired propulsion performance. Further the effect of divergent nozzle length and half angle on detonation wave structure was analyzed. The simulations have been done using Ansys 14 Fluent platform. The LES turbulence model was used to simulate the combustion wave reacting flows in combustor with standard wall function. From these numerical simulations among four acquaint nozzles the highest thrust augmentation could be attained in divergent nozzle geometry and detonation wave propagation velocity eventually reaches to 1830 m/s, which is near about C-J velocity. Smaller the divergent nozzle half angle has a significant effect on faster detonation wave propagation.