• 대한기계학회논문집B
• /
• 제33권4호
• /
• pp.215-224
• /
• 2009

Analysis for various driven nozzle position changes. The analysis was done for different Reynolds number in entrance region of jet-pump and for several diameter ratios of driven nozzle. (1) The largest absorption energy was found at the point s=1 in condition of diameter ratio 1:3.21 and point s=0.5 in condition of diameter ratio 1:2.25. (2) The absorption energy was not related to the change of entrance velocity and the driven nozzle position having the largest absorption energy was function for cross section ratio. (3) As the position of driven nozzle moves to the downstream, the absorption energy gets weaker. Because the energy from swirl was lost at the cross section gets smaller. (4) As the position of driven nozzle moves to the downstream, the injection energy leans to the upper direction wall and as the Reynolds number increase, the lean phenomenon is more distinct. (5) The flow quantity of driven nozzle, the diameter ratio 1:3.21, was 32% higher than that of 1 : 2.25 and as the inlet velocity gets faster the efficiency decreased. And as the cross section of the driven nozzle increases.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.25-25
• /
• 2009

종래의 위보기 자세에서 용접은 중력이 모재의 표면으로 향하고 있어 용융금속이 중력에 의해 표면방향으로 흘러내리게 되어 용접 실시가 불가능하였다. 이에 Shield Gas Force, Trailing Gas Force 그리고 Ahead Gas Force를 적절히 적용하여 Position Welding에서 중력으로 인해 Molten Metal이 처지는 문제를 극복하여 생산성 향상으로 연결할 수 있음을 선행 실험을 통해 확인하였으나 기존의 C(Convergent)형, CP(Convergent Divergent)형 및 P(Parrallel)형 가스 노즐은 용접조건에 따라 실드 가스의 소모량이 많고, 토출되는 실드가스력이 부족하여 용접시 볼록한 이면 비드 형성을 위한 용융 풀을 효과적으로 제어 할 수 없다. 따라서 본 연구에서는 동일량의 실드 가스 공급시 가스 노즐을 통해 토출되는 실드가스의 소모를 줄이고 실드가스력을 극대화하여 저가의 고생산성을 가진 친 환경 용접기술(Green welding)에 부합하는 CDP(Convergent Divergent Parrallel)형 가스 노즐을 제작하여 기존의 CP형 가스 노즐과 비교 분석하였다. 또한 Overhead Position에서의 비드형상제어와 Flat Position에서 방풍효과를 비교해 보았다. 그 결과 CDP Nozzle은 CP Nozzle보다 동일한 유량에서 풍속은 3.5배, 냉각능력은 1.5배, 가스압력은 6.25배로 우수한 성능을 확인할 수 있었고, Overhead Position에서 가스 유량을 동일하게 하여 용접하였을 때 CP Nozzle의 경우 오목한 이면비드가 나타났지만 CDP Nozzle의 경우 볼록하게 양호한 이면비드 형상이 나타났고, Flat Position에서의 방풍효과 비교실험에서 CDP Nozzle에서는 깊고 균일한 용입을 CP Nozzle에서는 불안정한 용입이 나타났는데 이는 CDP Nozzle의 경우 풍속에 의한 Arc Blow가 적게 발생하여 상대적으로 더 나은 용입을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권4호
• /
• pp.550-556
• /
• 2008

The aim of this research is to analyze the influence of motive pressure, driving nozzle position and nozzle throat ratio on the performance of ejector. The experiment was conducted in the variation of motive pressure of 0.196, 0.294, 0.392 and 0.490MPa respectively. The position of driving nozzle was varied in difference locations according to mixing tube diameter(0.5d, 1d, 2d, 3d, 4.15d, 5d and 6d). The experimental results show when the nozzle outlet is located at 3d, the flow characteristics change abruptly. It is shown that the suction flow rate and pressure lift ratio of ejector is influenced by the driving nozzle position. At nozzle position location of the Id of mixing tube diameter the performance of ejector gives the best performance.

• 대한인간공학회지
• /
• 제30권5호
• /
• pp.629-636
• /
• 2011

Objective: The aim of this study is developing an elderly automatic showering system by optimizing nozzle position and angle of water injection on ergonomics approach. Background: The elderly living in nursing home or hospital were increased by an aging population. Helping the elderly on showering is so hard. In addition, the existing showering/bathing systems are not effective because shower pattern of the elderly and washed range of nozzle were not considered. Method: Firstly, basic specification were determined by anthropometric approach. Secondly, position of nozzle and angle of water injection were determined through observation of elderly behavior on showering. And, finally, they were optimized by washing test and showering simulation. Results: On showering importance of body parts were able to analysis through observation of elderly behavior. The position of nozzle and angle of water injection was able to optimize by showering simulation. The automatic showering system was developed by considering their results. Conclusion: The most important technology of developing a showering system is the determining position of nozzle and angle of water injection, number of nozzle. It was developed by applying its results through user centered-research. Application: The user centered-research of developing products was able to apply directly to develop automatic bath, showering products etc. Further more it was available to apply senior friendly products.

• 대한환경공학회지
• /
• 제33권5호
• /
• pp.325-331
• /
• 2011

연소과정 중에 발생하는 질소산화물을 저감하는 기술인 MILD 연소에 대하여 연료노즐과 공기노즐의 위치와 공기유량을 변화하면서 나타나는 연소특성을 수치해석을 통하여 연구하였다. 본 연구의 MILD 연소로는 연료노즐과 공기 노즐 사이에 연소배기가스의 배출구가 있는 연소로를 이용하였다. 공기노즐은 8개, 연료노즐은 4개를 사용하였다. 연료노즐이 연소로 중앙 부근에 위치한 연소로의 경우에 공기유량이 적을 때는 연소반응대가 연료노즐에서부터 연소로 벽면으로 치우치게 되지만 공기유량이 커지면 연소반응대가 연료노즐 측에서 시작하여 연료노즐 상부로 형성된다. 공기노즐이 연소로 중앙부분에 위치한 경우에 공기유량이 적을 때는 연소반응대가 공기노즐 부근에서 시작하여 연소로 벽면으로 치우치지만 공기유량이 증가하면 연소반응대가 연료노즐 측으로 옮겨가게 된다. 두 가지 경우 모두 공기유량이 증가하면 연소반응대에서 최대온도가 증가하고 따라서 배기가스에서의 NOx 농도가 증가한다. 두 가지 노즐 위치에서의 NOx 생성을 비교해 보면 공기노즐이 연소로 중앙에 위치한 경우가 연료노즐이 연소로 중앙에 위치한 경우보다 NOx 농도가 현저히 적음을 알 수 있었다. 본 연구의 결과로부터 NOx 저감과 연료의 미연가스 배출을 감안할 때 공기노즐이 연소로 중앙에 위치하고 이론공기량에 해당하는 공기량을 분출할 때 NOx 생성에 가장 효과적임을 알 수 있었다.

• 산업기술연구
• /
• 제20권B호
• /
• pp.45-53
• /
• 2000

A numerical study is done on the thrust vector control using gaseous secondary injection in the rocket nozzle. A commercial code, PHOENICS, is used to simulate the rocket nozzle flow. A $45^{\circ}-15^{\circ}$ conical nozzle is adopted to do numerical experiments. The flow in a rocket nozzle is assumed a steady, compressible, viscous flow. The exhaust gas of the rocket motor is used as an injectant to control the thrust vector of rocket at the constant rate of secondary injection flow. The injection location which is on the wall of rocket is chosen as a primary numerical variable. Computational results say that if the injection position is too close to nozzle throat, the reflected shock occurs. On the other hand, the more mass flow rate of injection is needed to get enough side thrust when the injection position is moved too far from the throat.

• 한국가스학회지
• /
• 제23권3호
• /
• pp.1-6
• /
• 2019

본 연구는 폐기물 소각로에서 질소산화물 저감을 위해 고온의 배기가스를 연소로에서 재순환하여 연소용 공기와 혼합하여 배기가스 재순환을 이용한 방법에서 고온의 배기가스를 별도의 동력 팬이 없이 코안다 노즐을 이용한 배기가스 재순환 장치에 관한 연구이다. 코안다 노즐에서 공기 공급 노즐 간극의 변화와 공기 공급 노즐의 위치에 따른 배기가스 재순환 유량 특성과 혼합 가스의 출구에서 평균온도 변화를 살펴보았다. 공기 공급 노즐의 간극이 3.22, 4.03, 4.84 mm로 변할 때 가장 좁은 3.22 mm일 때가 배기가스 재순환 유량과 공기 공급 유량의 비인 배기가스 재순환 유량비가 2.227로 가장 재순환 유량이 크게 나타났고 혼합가스 평균 온도는 $594.8^{\circ}C$로 나타났다. 공기 공급 노즐의 위치가 코안다 노즐 목의 전방 위치, 목 위치, 확관 위치로 변할 때를 살펴보았으며 전방 위치와 목 위치일 때는 재순환 유량비가 1.843으로 거의 같은 값이고 확관 위치에서는 1.696으로 나타났으며 평균 온도는 $559.8^{\circ}C$와 $544.3^{\circ}C$로 나타났다.

• 대한인간공학회지
• /
• 제31권2호
• /
• pp.389-396
• /
• 2012

Objective: The aim of this study is to design an auto showering system regarding bed type for old people or bedridden patients. Background: The rapid growth concerning the aging population leads to an increase in elderly bedridden patients living in senior care centers and hospitals where care givers have difficulty bathing older people with limited mobility. Method: In this study, a showering equipment for experiment was based on anthropometric and researching existing products. The nozzle position was optimized by showering tests and simulations using showering equipment. Results: The problems regarding the existing products were analyzed and the nozzle position was optimized through showering tests. The number, position, and spraying angle of the nozzle were optimized through showering simulations. The automatic showering system concerning bed type was designed by considering their results. Conclusion: When designing an automatic showering system, the most important design element involves determining the position of nozzle and angle of water injection and the number of nozzles. The system was developed by applying the results through user centered-research. Application: The user centered-research for developing products was applied directly in order to develop automatic baths, showering products etc. Furthermore, it was also available to be applied towards senior friendly products.

• 자원리싸이클링
• /
• 제11권3호
• /
• pp.17-24
• /
• 2002

There has been an increasing demand over the years for steels with lower[s] content. For the purpose of improving the efficiency of desulphrization in the powder injection process of ladle, experimental studies were carried out by using cold model to optimize the lance configuration, gas flow rate, immersion depth of lance nozzle, position of lance nozzle relative to the ladle and the effect with slag, etc. As the results of this study, it was made clear that 2-hole nozzle lance (C, E type) placed in an asymmetric position gives the shortest mixing times.

• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.41-48
• /
• 2014

Direct writing(DW) is a method of patterning materials to a substrate directly, without a mask. It can use a variety of materials and be applied to various fields. Among DW systems, the flow-based type, using a syringe pump and nozzle, is simpler than other types. Furthermore, the range of materials is exceptionally wide. In additive processes, a three dimensional structure is made of stacking layer. Each layer is made of several lines. In this regard, good surface roughness of fabricated layers is essential to three dimensional fabrication. The surface roughness of any fabricated layer tends to change with the dispensing pattern. When multiple layers fabricated by a nozzle dispensing system are stacked, control of the nozzle position from the substrate is important in order to avoid interference between the nozzle and the fabricated layer. In this study, a fluid direct writing system for three dimensional structure fabrication was developed. Experimentsto control the position of the nozzle from substrate were conducted in order to examine the characteristics of the material used in this system.