• Journal of Environmental Health Sciences
• /
• v.27 no.2
• /
• pp.51-59
• /
• 2001

Song stream is located in the upstream of the Namhan River. Normal times, the stream flows down to the east sea through the drainage pipe but at rainy season, it flows to the Namhan River. There are large stock farm, leisure town and cultivated land in this basin. The pollutants from these contamination source cause eutrophication at lake Doam and deterioration of water quality in namdai stream. In this case, this study was carried out to evaluate water quality and environmental capacity as well as economical efficiency of each industry. The basin shape factor of subject stream was 0.315, slope is higher than usual basin. The BOD, T-N and T-P productive contamination loading from each contamination source was 2,690, 974 and 194 kg/day, respectively, and major contamination source was stock farm and cultivated land. Annual BOD, T-N, T-P distribution(median value) of Song stream showed 1.0~2.2 mg/L, 3.16~5.85 mg/L and 0.024~0.197 mg/L Doam lake showed 1.1~1.9, 2.51~3.89 and 0.042~0.114 mg/L, respectively. Being compared of water quality at main stream between past and present, it showed that the water quality has improved since last five years. BOD improvement rate was 8~50%. Run off loading of BOD, T-N, T-P was 366, 1129, 17.2 kg/day, and run off rate was 13.6%, 86.2%, 11.3% respectively. Finally, the result of productivity survey of each industry, leisure town, cultivated land and large stock farm was 118, 46, 50 billion won, per T-P 1kg productive, and productivity portion was 100, 39, 42% respectively, and the highest economical efficiency industry was leisure facilities.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.6
• /
• pp.565-571
• /
• 2016

This paper investigates macro- and microscopic fractography performed on fracture specimens from low cycle fatigue (LCF) testings through an Alloy 617 base metal and weldments. The weldment specimens were taken from gas tungsten arc welding (GTAW) pad of Alloy 617. The aim of the present study is to investigate the macro- and microscopic aspects of the low cycle fatigue fracture mode and mechanism of Alloy 617 base metal and GTAWed weldment specimens. Fully axial total strain controlled fatigue tests were conducted at room temperature with total strain ranges of 0.6, 0.9, 1.2 and 1.5%. Macroscopic fracture surfaces of Alloy 617 base metal specimens showed a flat type normal to the fatigue loading direction, whereas the GTAWed weldment specimens were of a shear/star type. The fracture surfaces of both the base metal and weldment specimens revealed obvious fatigue striations at the crack propagation regime. In addition, the fatigue crack mechanism of the base metal showed a transgranular normal to fatigue loading direction; however, the GTAWed weldment specimens showed a transgranular at approximately $45^{\circ}$ to the fatigue loading direction.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.4
• /
• pp.484-514
• /
• 1994

Cantilever bridge is widely used by mny clinicians, but its worst mechanical character, so called Class I lever system, makes dentists hesitate to restore the missing tooth with it. Therefore it is important to study stress of the cantilever bridge. In this study, two models of cantilever bridges that restores the missing mandibular second molar with two abutment teeth were constructed. One model was a type of cantilever bridge supported by a normal alveolar bone, the other one was supported by an alveolar bone resorbed to its 1/3 of root length. Maximum bite force(550N) and funtional maximum bite force(300N) were vertically applied to the distal end of the pontic, distal 1/3, and distal half of the pontic. And each force was also applied to centric occlusal contacts as a distributed force. Total 16 loading cases were compared and analyzed with 3-dimensional finite element method. The results were as follows: 1. The stress was concentrated on the joint of the pontic and the retainer, grooves, and distal cervical margin of the posterior retainer. 2. In case of maximum bite force(550N) at the end of the pontic, the risk of fracture at the joint of the pontic and the retainer was high. 3. In case of distributed force in centric occlusion and functional maximum bite force(300N), the stresses were less than the yield strength of the type VI gold for any loading cases. 4. In case of alveolar bone resorption, the occlusal force to the cantilever pontic caused more stress on the root apex and less stress on the alveolar crest region of the distal surface of the posterior abutment. 5. In case of alveolar bone resorption, the displacement was larger than that of normal alveolar bone in all loading cases.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.137-146
• /
• 2002

Geomembrane, compacted clay liner, and geosynthetic clay liner (GCL) are widely used to prevent leachate from leaking to adjacent geo-environment at a municipal solid waste (MSW) landfill. Interface shear strength between GCL and geomembrane installed at a landfill side slope is important properties for the safe design of side liner or final cover systems. The interface shear strength between two geosynthetics was estimated by a large direct shear test in this study. The shear strength was evaluated by the Mohr-Coulomb failure criterion. The effects of normal stress, hydration or dry condition, and a hydration method were investigated. The test results show that the interface shear strength and shear behavior varied depending up on the level of normal stress, the type of geosynthetic combinations, and a hydration method. When GCLs were sheared after being hydrated under 6kPa loading, the results were consistent with those published by other researchers. Summaries of friction angles, normal stress and hydration condition is presented. These friction angles could be used as a reference value at a site where similar geosynthetics are installed.

• Progress in Medical Physics
• /
• v.4 no.2
• /
• pp.19-25
• /
• 1993

Treatment planning of lung cancer with density corrected Computed tomography. Eighty-seven patients with lung cnacer who had radiation therapy in Yeungnam University Medical Center between, April 1 1990 and Aug. 30 1993 were retrospectively evaluated total tumor dose, dose distribution, field correction, and loading change, compared with contour or CT image planning and density corrected CT planning. In dose distribution, higher dose was calculated in compare with density corrected CT planning less than 5% difference were found in 45 patient(52%), 5-10% in 25 patients (29%), 10-15% in 15 patients (17%) and over 15% in 2 patients (2%). Correction of treatment field was performed in 18 patients (21%) and changing of dose loading was given in 15 patients (17%). In conclusion, we emphasize that density corrected CT planning is the very important factor which contribute to increase therapeutic gain by exact selection of target volume, target dose, normal tissue dose and dose of critical organ.

• International Journal of Highway Engineering
• /
• v.4 no.4 s.14
• /
• pp.23-39
• /
• 2002

This study dealt with developing a new approach for finding properties which might represent rut resistance characteristics of asphalt mixture under static loading. Two aggregates, a normal asphalt (pen 60-80) and 5 polymer-modified asphalts were used in preparation of 12 dense-graded mixtures. Marshall mix design was used in determination of OAC and each mixture at the OAC was prepared for a newly-developed Kim test on Marshall specimen (S=10cm) and gyratory specimen (S=15cm), and for wheel tracking test. Kim test used Marshall loading frame and specimens were conditioned for 30min at $60^{\circ}C$ before loading through Kim tester an apparatus consisting of a loading column and a specimen and column holder Diameter (D) of column was 3cm and 4cm with each column having different radius (r) of round cut at the bottom. The static load was applied at 50mm/min in axial direction of the specimen, not in diametral direction. The maximum load ($P_{max}$) and vertical deformation (y) at $P_{max}$ point were obtained from the test. A strength value was calculated based on the $P_{max}$ r, D and y by using the equation $K_D = 4P_{max}/{\pi}(D-2(r-\sqrt{2ry-y^2}))^2$ and is defined as the deformation strength ($kgf/cm^2$). The values of $P_{max}$/y and $K_I=K_D/y$ were also calculated. In general the leading column diameter and radius of round cut were significant factors affecting $K_D$ and $P_{max}$ values while specimen diameter was not. The statistical analyses showed the $K_D$ had the best correlation with rut depth and dynamic stability. The next best correlation was found from $P_{max}$ which was followed by $P_{max}$/y and $K_I$ in order.

• Korean Journal of Biological Psychiatry
• /
• v.11 no.2
• /
• pp.94-103
• /
• 2004

Objective:There have been a kind of transmethylation theory that high homocysteine serum concentration affects schizophrenia by neurotoxic mechanism and clinical reports that some schizophrenic patients with high homocysteine were improved by high folate ingestion. This study was done to confirm previous research results and find the clinical characteristics of schizophrenia showing high serum homocysteine and low folate. Method:We compared the serum levels of homocysteine, folate and vitamin B12 level between 234 schizophrenic patients(male 99, female 135) group and 234 normal controls(male 99, female 135) group. The subjects of two groups were age and sex matched. The evaluated clinical characteristics items were sex, age, onset of disease, hereditary loading, disease course, hallucination and subtype of schizophrenia. Results:1) Homocysteine level of the schizophrenia group was significantly higher than the normal control group and folate level of the schizophrenia group was significantly lower than the normal control group. Homocysteine level was more negatively correlated with folate level in the schizophrenia group than the normal control group. 2) The percentage of high homocysteine(above 12.46umol/L;90 percentile of normal control) was 33.8% of schizophrenia patients and 51.5% of male schizophrenia. The percentage of low folate(below 3.8nM/L;bottom tertile of normal control) was 66.2% of schizophrenia. 3) In low folate group and not-low folate group, schizophrenia showed significantly higher homocysteine level than normal control. Especially, low folate schizophrenia group showed significantly higher homocysteine level than low folate normal control group. Conclusions:Some schizophrenia patients with high serum homocysteine may be genetic defector and having low folate serum level. In that case, folate ingestion could be a good management for clinical improvement.

• Geotechnical Engineering
• /
• v.12 no.3
• /
• pp.35-48
• /
• 1996

Reinforced soil structures may experience large local movements between soil and reinforcement. The failure modes of a reinforced structure depend on several factors which are governed by deformation and slipping of the reinforcement. In some cases, pulling out of the reinforcement may occur instead of rupturing, The growing use of geosynthetic liner system for storage of solid and liquid wastes has led to a number of slope instability problems where the synthetic liner may undergo a large amount of stretching and slipping as a result of the loading. The conventional finite element model for the soil-reinforcement interface uses a zero thickness joint element with normal and shear stiffnesses and can only accommodate a small amount of deformation. When a large slippage occurs, the model provides an i ncorrect mechanism for deformation. This paper presents a new interface finite element model which is able to simulate a large amount of slippage between soil and reinforcement. The formulation of the model is presented and the capability of the model is demonstrated using illustrative examples.

• Smart Structures and Systems
• /
• v.16 no.5
• /
• pp.781-806
• /
• 2015

A unified formulation of finite layer methods (FLMs), based on the Reissner mixed variational theorem (RMVT), is developed for the three-dimensional (3D) coupled electro-elastic analysis of simply-supported, functionally graded piezoelectric material (FGPM) plates with open- and closed-circuit surface conditions and under electro-mechanical loads. In this formulation, the material properties of the plate are assumed to obey an exponent-law varying exponentially through the thickness coordinate, and the plate is divided into a number of finite rectangular layers, in which the trigonometric functions and Lagrange polynomials are used to interpolate the in- and out-of-plane variations of the primary field variables of each individual layer, respectively, such as the elastic displacement, transverse shear and normal stress, electric potential, and normal electric displacement components. The relevant orders used for expanding these variables in the thickness coordinate can be freely chosen as the linear, quadratic and cubic orders. Four different mechanical/electrical loading conditions applied on the top and bottom surfaces of the plate are considered, and the corresponding coupled electro-elastic analysis of the loaded FGPM plates is undertaken. The accuracy and convergence rate of the RMVT-based FLMs are assessed by comparing their solutions with the exact 3D piezoelectricity ones available in the literature.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.165-169
• /
• 2005

The fire damage of building wouid effect on the safety of structure. When the reinforced concrete structure is heated by high temperature due to the fire, the structural resisting-force will be decreased. In a way, it is a requirement to use high strength concrete for high rise building. Particularly, fire resistance properties of high-strength concrete is more important than normal strength concretes. The fire outbreak of a high strength concrete by sudden temperature rise is a main problem, and causes crack by thermal stress, loading to the deterioration of the durability. In this study, normal and high strength mortar were exposed to a high temperature environment. And than fundamental data for the character change of concrete heated highly were presented by measuring compressive strength of concrete with polypropylene and vinylon fiber, before and after heating. As the results, it is proven that high strength mortar with polypropylene and vinylon fiber for prevents deterioration of durability by fiber.