• Journal of the Korean Society of Combustion
• /
• v.6 no.2
• /
• pp.43-49
• /
• 2001

Instantaneous, three-dimensional scalar dissipation rates of the reaction progress variable are measured in turbulent premixed Bunsen flames of lean hydrocarbon/air mixtures with the two-sheet, two-dimensional Rayleigh scattering technique. The flames investigated are located in the turbulent flame-front regime on a newly proposed combustion diagram for premixed flames. The conditionally-averaged mean scalar dissipation rates, $N_{\zeta}$ are found to be lower than the calculated laminar values, indicating a locally broadened flame front. In agreement with previous measurements, the maximum of $N_{\zeta}$, decreases strongly with increasing Karlovitz numbers. The conditional probability density functions are close to a log-normal distribution for scalar dissipation rates conditioned at the progress variable value where the scalar dissipation is maximum in unstretched laminar flame calculations. The time scale for the Favre-averaged mean scalar dissipation rate decreases in general across the turbulent flame brush from the unburnt to burnt side.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.609-612
• /
• 2007

The co-combustion of coal and RPF(Refuse Plastic Fuel) mixture has been experimented in a commercially operating CFB coal boiler and the emissions such as SOx, NOx, TSP and dioxine were measured at the stack. The experimented RPF was supplied by domestic RPF company that is commercially producing RPF pellet from the wasted plastics. Up to 15% of total coal was substituted to RPF and no trouble was happened during normal boiler operation. SOx and NOx concentration was reduced about $15{\sim}20$% and TSP(Total Suspended Particle) was drastically reduced about 30% during co-combustion. Dioxine concentration at mixing ratio of 7.5% was $0.0487ng{\sim}TEQ/Sm^3$ ($O_2$, 12%) that satisfied governmental emission regulation.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.159-165
• /
• 2003

This paper describes numerical efforts to characterize the flame-holding and air-fuel mixing process of model SCRamjet engine combustor, where a hydrogen jet injected into a supersonic cross flow and in a cavity. Combustion phenomena in a model SCRamjet engine, which has been experimentally studied at University of Queensland and Australian National University using a free-piston shock tunnel, was observed around separation region of upstream of the normal injector and inside of cavity. The results show that the separation region and cavity generates several recirculation zones, which increase the fuel-air mixing. Self ignition occurs in the separation-freestream and cavity-freestream interface.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.193-207
• /
• 2002

The present study is mainly motivated to investigate the vaporization, autoignition, and combustion of liquid fuel spray injected into high pressure environment. In order to represent these phenomena realistically, discrete droplet model (DDM) which simulates the spray using finite number of representative droplets was adopted for detailed consideration of the finite rate of uansport between liquid and gas phases. The Eulerian-Lagrangian formulation was used to analyze the two-phase interactions. The high pressure vaporization model was applied using the thermodynamic and phase equilibrium at droplet surface. The high pressure effect as well as high temperature effect was considered in the calculation of liquid and gas properties. The characteristics of spray in high pressure environment were explained by comparison with normal pressure case.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.9
• /
• pp.1273-1281
• /
• 2003

The present study is mainly motivated to investigate the vaporization, auto-ignition, and combustion of liquid fuel spray injected into high pressure environment. The unsteady, multi-dimensional models were used for realistic simulation of spray as well as prediction of accurate ignition delay time. The Separated Flow (SF) model which considers the finite rate of transport between liquid and gas phases was employed to represent the interactions between spray and gas field. Among the SF models, the Discrete Droplet Model (DDM) which simulates the spray using finite number of representative samples of discrete droplets was adopted. The Eulerian-Lagrangian formulation was used to analyze the two-phase interactions. In order to predict an evaporation rate of droplet in high pressure environment, the high pressure vaporization model was applied using thermodynamic equilibrium and phase equilibrium at droplet surface. The high pressure effect as well as high temperature effect was considered in the calculation of liquid and gas properties. In case of vaporization, an interaction between droplets was studied through the simulation of spray. The interaction is shown up differently whether the ambient gas field is at normal pressure or high pressure. Also, the characteristics of spray behavior in high pressure environment were investigated through the comparison with normal ambient pressure case. In both cases, the spray behaviors are simulated through the distributions of temperature and reaction rate in gas field.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.4
• /
• pp.493-500
• /
• 2002

The operational data of diesel generator engine is two kinds of data. One is interactive the other is non interactive. We can find the fault information from interactive data measured for every sampling time when the changing rate, direction and status of data are investigated in comparition with those of normal status to diagnose the fault of combustion system. The various data values of combustion system for diesel engine are not proportional to load condition. The criterion to decide the level of data value is not absolute but relative to relational data. This study proposes to compose malfunction diagnosis engine using neural networks to decide that level of data value is out of normal status with the data collected from generator engine of the ship using the commercial data mining tool. This paper investigates the real ship's operational data of diesel generator engine and confirms usefulness of fault detecting through simulations for fault detecting.

• Journal of the Korean Society of Combustion
• /
• v.4 no.2
• /
• pp.75-83
• /
• 1999

The effect of temperature distributions on soot volume fraction in double-concentric diffusion flames have been investigated experimentally. Using fine thermocouple wires and a rapid insertion mechanism, we have measured temperature without the effect of soot particles attached to the thermocouple junction, which can lower the temperature signal about 100 K by increasing the heat loss from the junction by radiation. The temperature at the flame axis is higher in the double-concentric diffusion flames than in normal co-flow diffusion flames because of the inverse diffusion flame. However, it is almost the same as that at the periphery of normal flames, on which the inverse flame does not have an effect. Thus, the lower soot concentration found in the double-concentric diffusion flame can be explained by the effect of nitrogen diffusion from the central air jet.

• Fire Science and Engineering
• /
• v.19 no.4 s.60
• /
• pp.26-31
• /
• 2005

In order to evaluate the fire and explosion involved and to ensure the safe and optimized operation of chemical processes, it is necessary to know combustion properties. Explosion limit is one of the major combustion properties used to determine the fire and explosion hazards of the flammable substances. In this study, the explosion limits of alcohols were predicted by using the normal boiling points and the flash points based on a solution theory. The values calculated by the proposed equations agreed with literature data within a few percent. From the given results, using the proposed methodology; it is Possible to Predict the explosion limits of the other flammable substances.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.344-349
• /
• 2003

The purpose of this study is to ascertain the ability of New type cutter using Hybrid Rocket Propulsion System to cut normal carbon steel and also compound metal like stainless steel which cannot be cut by regular oxygen-acetylene cutter. To compare cutting performance, Two different types of experiment with oxygen-acetylene and Hybrid Combustion cutters were performed. As a result, Hybrid Combustion cutter is used to cut both carbon steel and stainless steel with cutting speed of 400mm/min(carbon steel) and 250mm/min(stainless steel). Otherwise, oxygen-acetylene cutter can be used to cut only carbon steel with cutting speed of 500 $^{\sim}$ 700mm/min. The possibility of Hybrid Combustion cutter as a cutting machine was confirmed.

• Journal of the Korean Society of Combustion
• /
• v.21 no.3
• /
• pp.7-15
• /
• 2016

The fuel in conventional liquid fuel combustor is atomized by spray method for high efficiency and low emissions. To improve the overall fuel efficiency and lower pollutant emissions in liquid fuel combustion systems, the effective spatial and temporal separation of droplet evaporation from normal spray process is needed. In this paper, the recuperation of high temperature burnt gas for fuel evaporation was proposed to develop a cylindrical premixed combustor. The recuperation process using U shaped tube is effective to evaporate the liquid fuel. The results show that the flame mode is changed into red radiation flame, blue flame and lift off flame with decreasing equivalence ratio as gas fuel combustion mode. In particular, the blue flame is found to be very stable at heating load 9.2 kW and equivalence ratio 0.731. NOx was measured blow 105 ppm ($O_2$ zero base) from equivalence ratio 0.705 to 0.835. CO which is a very important emission index in liquid fuel combustor was observed below 5 ppm ($O_2$ zero base) under the same equivalence region.