• Advances in concrete construction
• /
• 제9권4호
• /
• pp.413-421
• /
• 2020

For steel-concrete girders made composite using shear studs, initial damage on studs induced by weld defect, unexpected overloading, fatigue and others might degrade the service performance and even threaten the structural safety. This paper conducted a numerical study to investigate the static behavior of damaged stud shear connectors that were embedded in ultra high performance concrete (UHPC). Parameters included damage degree and damage location. The material nonlinear behavior was characterized by multi-linear stress-strain relationship and damage plasticity model. The results indicated that the shear strength was not sensitive to the damage degree when the damage occurred at 2/3d (d is the stud diameter) from the stud root. An increased stud area would be engaged in resisting shear force as the distance of damage location from stud root increased and the failure section becomes inclined, resulting in a less reduction in the shear strength and shear stiffness. The reduction factor was proposed to consider the degradation of the shear strength of the damaged stud. The reduction factor can be calculated using two approaches: a linear relationship and a square relationship with the damage degree corresponding to the shear strength dominated by the section area and the nominal diameter of the damaged stud. It was found that the proposed method is preferred to predict the shear strength of a stud with initial damage.

• 콘크리트학회지
• /
• 제11권1호
• /
• pp.231-242
• /
• 1999

면외 바닥하중과 토압과 수압에 의한 면내 압축력을 받는, 깊은 지하구조에 사용되는 플랫플레이트 슬래브에 대한 수치해석연구를 실시하였다. 비선형 유한요서해석을 위하여 재료와 기하학적 비선형효과를 고려한 수치해석프로그램을 개발하였으며, 이 수치해석방법은 4 변이 단순지지된 플레이트에 대한 실험결과와 비교에 의하여 검증되었다. 해석모델로서 국내 콘크리트계산규준의 직접설계법에 의하여 설계된 플랫플레이트 슬래브가 사용되었다. 하중조합과 하중순서에 대한 연구를 통하여 플랫플레이트 슬래브의 강도를 지배하는 하중조건을 연구하였으며, 이 지배하중을 받는 슬래브에 대한 변수연구를 통하여 철근비, 형상비, 콘크리트강도, 세장비에 따를 슬래브의 강도변화를 연구하였다. 이 연구결과를 바탕으로 바닥하중증대법을 제시하였다.

• 비파괴검사학회지
• /
• 제30권1호
• /
• pp.46-53
• /
• 2010

항공기용 복합재료 내부 여러 층에서 발생하는 박리를 정량적으로 평가하기 위한 X-ray 후방산란 검사장치를 개발하였다. 복합재료 두께방향으로의 역산란 밀도변화로부터 층간 박리를 검사하는 슬릿 방식의 카메라와 컴퓨터로 제어되는 X-ray 선원, 그리고 센서로 구성되는 X-ray 후방산란장치를 제작하여 그 성능을 충격하중에 의해 만들어진 인공결함시편을 이용해 검증하였다. 결함평가를 위해 복합재료내 산란장의 크기를 이론적으로 계산하는 수학적 해석 모델을 볼츠만 방정식을 이용하여 제안하였으며 적응필터 알고리즘을 사용하여 산란 노이즈를 최소화 하였다. 다중 박리 결함을 X-ray 후방산란장치를 통해 효과적으로 검출하였으며, 박리 위치와 박리 상태를 모두 정확하게 검사할 수 있음을 실험을 통해 확인하였다.

• 한국전산구조공학회논문집
• /
• 제15권4호
• /
• pp.567-578
• /
• 2002

본 논문은 8절점 고체요소를 이용하여 항공기 충돌에 의한 원전 격납건물의 동적 거동을 분석하고 그 결과를 기술하였다. 콘크리트의 재료적 특성을 표현하기 위하여 Drucker-Prager항복기준을 바탕으로 항복면과 파괴면을 형성하였다. 이때 항복면과 파괴면은 콘크리트의 소성변형이 누적되면 가변하는 것으로 가정하였다. 철근의 재료특성은 변형도에 의존적인 탄성/점소성모델을 이용하여 표현하였다. 표준고체요소의 성능저하를 방지하기 위하여 Hughes가 제시한 B bar법을 바탕으로 변형도-변위관계 행렬을 형성하였다. 동적 시간이력해석을 수행하기 위하여 안정적인 수렴성을 가지는 암시적인 Newmark법을 도입하였다. 마지막으로 시간이력해석을 통하여 콘크리트 균열변형도의 수준과 충돌하는 항공기의 종류에 따른 격납건물의 동적거동변화를 조사하고 이를 정량적으로 기술하였다.

• 한국농공학회지
• /
• 제39권3호
• /
• pp.72-82
• /
• 1997

In all inelastic deformations time rate effects are always present to some degree. Whether or not their exclusion has a significant influence on the prediction of the material behaviour depends upon several factors. In the study of structural components under static loading conditions at normal temperature it is accepted that time rate effects are generally not important. However metals, especially under high temperatures, exhibit simultaneously the phenomena of creep and viscoplasticity. In this study, elastoplastic and elasto-viscoplastic models include nonlinear geometrical effects were developed and several numerical examples are also included to verify the computer programming work developed here in this work. Comparisons of the calculated results, for the elasto-viscoplastic analysis of an internally pressurised thick cylinder under plane strain condition, have shown that the model yields excellent results. The results obtained from the numerical examples for an elasto-viscoplastic analysis of the Nuclear Reinforced Concrete Containment Structure(NRCCS) subjected to an incrementally applied internal pressure were summarized as follows : 1. The steady state hoop stress distribution along the shell layer of dome and dome wall junction part of NRCCS were linearly behave and the stress in interior surfaces was larger than that in exterior. 2.However in the upper part of the wall of NRCCS the steady state hoop stress in creased linearly from its inner to outer surfaces, being the exact reverse to the previous case of dome/dome-wall junction part. 3.At the lower part of wall of NRCCS, the linear change of steady state hoop stress along its wall layer began to disturb above a certain level of load increase.

• 한국도로학회논문집
• /
• 제15권5호
• /
• pp.47-55
• /
• 2013

PURPOSES : The purpose of this study is to investigate the optimal joint positions which can minimize distresses of concrete pavement containing box culvert with horizontally skewed angles. METHODS : The concrete pavement containing the box culvert with different skewed angles and soil cover depths was modeled by 3 dimensional finite element method. The contact boundary condition was used between concrete and soil structures in addition to the nonlinear material property of soil in the finite element model. A dynamic analysis was performed by applying the self weight of pavement, negative temperature gradient of slab, and moving vehicle load simultaneously. RESULTS : In case of zero skewed angle ($0^{\circ}$), the maximum tensile stress of slab was the lowest when the joint was positioned directly over side of box culvert. In case there was a skewed angle, the maximum tensile stress of slab was the lowest when the joint passed the intersection between side of the box culvert and longitudinal centerline of slab. The magnitude of the maximum tensile stress converged to a constant value regardless the joint position from 3m of soil cover depth at all of the horizontally skewed angles. CONCLUSIONS : More reasonable and accurate design of the concrete pavement containing the box culvert can be possible based on the research results.

• 비파괴검사학회지
• /
• 제20권6호
• /
• pp.545-554
• /
• 2000

충격에 의해 복합 재료 내에 발생하는 층간 박리를 정량적으로 평가하기 위한 비파괴 방법중에서 Compton X-ray 역산란 기술은 초음파에 비해 비접촉식이며 박리 층간의 상호간섭이 없어 복합재료 판면의 박리 층의 위치와 크기를 검사하는데 효과적인 방법으로 사용되어 왔다. 그러나 X-ray역산란 기술에 있어서 복합재료의 박리 층과 같은 미세한 결함의 측정을 위해 측정 정도를 높이면 역산란 양의 감소로 인해 신호 대 잡음 비(SNR)가 급격히 감소하여 결함검출 가능성이 크게 저하된다. 본 논문에서는 복합재료의 특성을 고려한 X-ray 역산란 모델을 기초로 적응필터를 사용하여 결함신호를 비선형 감쇄, 빔 경화(X-ray hardening), 비균질 특성과 같은 잡음 신호로부터 분리, 추출하는 방법을 제시하였다. 이렇게 분리된 결함신호로부터 정량적인 결함(박리)의 위치와 크기를 수학적 산란 모델과의 비교를 통해 최소 자승법을 이용하여 결정하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.282-286
• /
• 2000

In this paper, magneto-rheological(MR) damper is studied for vibration control of large infra structures under earthquake. Generally, active control devices need a large control force and a high power supply system to reduce the vibration effectively. Large and miss tuned control force may induce the dangerous situation such that the generated large control force acts to amplify the structural vibration. Recently, to overcome the weaknesses of the active control, the semi-active control method is suggested by many researchers. Semi-active control uses the passive control device of which the characteristics can be modified. Control force of the semi-active device is not generated from the actuator with power supply. It is generated as a dynamic reaction force of the device same as in the passive control case, so the control system is inherently stable and robust. Unlike the case of passive control, control force of semi-active control is adjusted depending on the measured response of the structure, so the vibration can be reduced more effectively against various unknown environmental loads. Magneto-rheological(MR) damper is one of the semi-active devices. Dynamic characteristics of the MR material can be changed by applying the magnetic fields. So the control of MR damper needs only small power. Response time of MR to the input voltage is very short, so the high performance control is possible. MR damper has a high force capacity so it is adequate to the vibration control of large infra structure. Because MR damper has a nonlinear property, normal control method used in active control may not be effective. Clipped optimal control, modified bang-bang control etc. have been suggested to MR damper by many researchers. In this study, sliding mode fuzzy control(SMFC) is applied to MR damper. Genetic algorithm is used for the controller tuning. To verify the applicability of MR damper and suggested algorithm, numerical simulation on the aseismic control is carried out. Simulation model is three-story building structure, which was used in the paper of Dyke, et al. The control performance is compared with clipped optimal control. The present results indicate that the SMFC algorithm can reduce the earthquake-induced vibration very effectively.

• Computers and Concrete
• /
• 제29권1호
• /
• pp.15-29
• /
• 2022

Concrete-filled steel tubes (CFSTs) are increasingly used as composite sections in structures owing to their excellent load bearing capacity. Therefore, predicting the mechanical behavior of CFST sections under axial compression loading is vital for design purposes. This paper presents the first study on the nonlinear analysis of heated CFSTs with high-strength concrete core containing steel fiber and waste tire rubber under axial compression loading. CFSTs had steel fibers with 0, 1, and 1.5% volume fractions and 0, 5, and 10% rubber particles as sand alternative material. They were subjected to 20, 250, 500, and 750℃ temperatures. Using flow rule and analytical analysis, a model is developed to predict the load bearing capacity of steel tube, and hoop strain-axial strain relationship, and axial stress-volumetric strain relationship of CFSTs. An elastic-plastic analysis method is applied to determine the axial and hoop stresses of the steel tube, considering elastic, yield, and strain hardening stages of steel in its stress-strain curve. The axial stress in the concrete core is determined as the difference between the total experimental axial stress and the axial stress of steel tube obtained from modeling. The results show that steel tube in CFSTs under 750℃ exhibits a higher load bearing contribution compared to those under 20, 250, and 500℃. It is also found that the ratio of load bearing capacity of steel tube at peak point to the load bearing capacity of CFST at peak load is noticeable such that this ratio is in the ranges of 0.21-0.33 and 0.31-0.38 for the CFST specimens with a steel tube thickness of 2 and 3.5 mm, respectively. In addition, after the steel tube yielding, the load bearing capacity of the tube decreases due to the reduction of its axial stiffness and the increase of hoop strain rate, which is in the range of about 20 to 40%.

• Design & Manufacturing
• /
• 제16권1호
• /
• pp.27-35
• /
• 2022

Thermoforming is a plastic manufacturing process that applies a force to stretch a film of heated thermoplastic material over an engineered mold to create a 3-dimensional shape. After forming, the shaped part can then be trimmed and finished to specification to meet an end-user's requirements. The process and thermoplastic materials are extremely versatile and can be utilized to manufacture parts for a very wide range of applications. In this study, based on K-BKZ nonlinear viscoelastic model, thermoforming process analysis was performed for an interior room-lamp. The predicted thickness was minimum at the corner of a molded film, and maximum at the center of the bottom. By using the Taguchi method of design of experiments, the effects of process conditions on residual stresses were investigated. The dominant factors were the liner thickness and the film heating time. As the thickness of the liner increased, the residual stress decreased. And it was found that the residual stress decreased significantly when the film heating temperature was higher than the glass transition temperature. A thermoforming mold and a trimming mold were manufactured, and the spring back was investigated through experiments. The dominant factors were film heating time, liner thickness, and lower mold temperature. As the film heating time and liner thickness increased, the spring back decreased. In addition, it was found that the spring back decreased as the lower mold temperature increased.