• Structural Engineering and Mechanics
• /
• 제50권3호
• /
• pp.287-304
• /
• 2014

A computer based iterative numerical procedure has been developed to analyse reinforced high strength concrete columns subjected to horizontal wave loads and eccentric vertical load by taking the material, geometrical and wave load non-linearity into account. The behaviour of the column has been assumed, to be represented by Moment-Thrust-Curvature relationship of the column cross-section. The formulated computer program predicts horizontal load versus deflection behaviour of a column up to failure. The developed numerical model has been applied to analyse several column specimens of various slenderness, structural properties and axial load ratios, tested by other researchers. The predicted values are having a better agreement with experimental results. A simplified user friendly hydrodynamic load model has been developed based on Morison equation supplemented with a wave slap term to predict the high frequency non-linear impulsive hydrodynamic loads arising from steep waves, known as ringing loads. A computer program has been formulated based on the model to obtain the wave loads and non-dimensional wave load coefficients for all discretised nodes, along the length of column from instantaneous free water surface to bottom of the column at mud level. The columns of same size and material properties but having different slenderness ratio are analysed by the developed numerical procedure for the simulated wave loads under various vertical thrust. This paper discusses the results obtained in detail and effect of slenderness in resisting wave loads under various vertical thrust.

• International Journal of Fluid Machinery and Systems
• /
• 제1권1호
• /
• pp.10-23
• /
• 2008

The development of pre-set wavelength G$\ddot{o}$rtler vortices are studied in the boundary-layer flows on concave surfaces of 1.0 and 2.0 m radius of curvature. The wavelengths of the vortices were pre-set by thin wires of 0.2 mm diameter placed 10 mm upstream and perpendicular to the concave surface leading edge. Velocity contours were obtained from velocity measurements using a single hot-wire anemometer probe. The most amplified or dominant wavelength is found to be 15 mm for free-stream velocity of 2.1 m/s and 3.0 m/s on the concave surface of R = 1 m and 2 m, respectively. The velocity contours in the cross-sectional planes at several streamwise locations show the growth and breakdown of the vortices. Three different regions can be identified based on the growth rate of the vortices. The occurrence of a secondary instability mode is also shown in the form of mushroom-like structures as a consequence of the non-linear growth of the G$\ddot{o}$rtler vortices. By pre-setting the vortex wavelength to be much larger and much smaller than the most amplified one, the splitting and merging of G$\ddot{o}$rtler vortices can be respectively observed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.121-122
• /
• 2008

Lithium Niobate (LN:LiNbO3) is a compound of niobium, lithium and oxygen. The characteristics of LN are piezoelectricity, ferroelectricity and photoelectricity, and which is widely used in surface acoustic wave (SAW). To manufacture LN device, the LN surface should be a smooth surface and defect-free because of optical property, but the LN material is processed difficult by traditional processes such as grinding and mechanical polishing (MP) because of its brittleness. To decrease defects, chemical mechanical polishing (CMP) was applied to the LN wafer. In this study, the suitable parameters scuh as pressure and relative velocity, were investigated for the LN CMP process. To improve roughness, the LN CMP was performed using the parameters that were the highest removal rate among process parameters. And, evaluation of optical property was performed by the optical reflectance and non-linear characteristic.

• 한국해양공학회지
• /
• 제29권1호
• /
• pp.1-8
• /
• 2015

An analytical model of liquid sloshing is developed to consider the energy-loss effect through a partially submerged porous baffle in a horizontally oscillating rectangular tank. The nonlinear boundary condition at the porous baffle is derived to accurately capture both the added inertia effects and the energy-loss effects from an equivalent non-linear drag law. Using the eigenfunction expansion method, the horizontal hydrodynamic force (added mass, damping coefficient) on both the wall and baffle induced by the fluid motion is assessed for various combinations of porosity, submergence depth, and the tank's motion amplitude. It is found that a negative value for the added mass and a sharp peak in the damping curve occur near the resonant frequencies. In particular, the hydrodynamic force and free surface amplitude can be largely reduced by installing the proper porous baffle in a tank. The optimal porosity of a porous baffle is near P=0.1.

• 한국해양공학회지
• /
• 제22권1호
• /
• pp.1-5
• /
• 2008

A 2-D Fluent-based numerical wave tank(FBNWT) capable of simulating wave propagating and overtopping is presented. The FBNWT model is based on the Reynolds averaged Naiver-Stokes equations and VOF free surface tracking method. The piston wave maker system is realized by dynamic mesh technology(DMT) and user defined function(UDF). The non-iteration time advancement(NITA) PISO algorithm is employed for the velocity and pressure coupling. The FBNWT numerical solutions of linear wave propagation have been validated by analytical solutions. Several overtopping problems are simulated and the prediction results show good agreements with the experimental data, which demonstrates that the present model can be utilized in the corresponding analysis.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권3호
• /
• pp.478-489
• /
• 2015

In the present study, a hydrodynamic hull-form optimization algorithm for a container ship was presented in terms of the minimum wave-making resistance. Bell-shaped modification functions were developed to modify the original hull-form and a sequential quadratic programming algorithm was used as an optimizer. The wave-making resistance as an objective function was obtained by the Rankine source panel method in which non-linear free surface conditions and the trim and sinkage of the ship were fully taken into account. Numerical computation was performed to investigate the validity and effectiveness of the proposed hull-form modification algorithm for the container carrier. The computational results were validated by comparing them with the experimental data.

• 대한조선학회논문집
• /
• 제47권2호
• /
• pp.188-195
• /
• 2010

Green water load is an important parameter to be considered in designing a modern ship or offshore structures like FPSO and FSRU. In this research, a numerical simulation method for green water phenomenon is introduced. The Navier-Stokes equations and the continuity equation are used as governing equations. The equations are calculated using Finite Difference Method(FDM) in rectangular staggered grid system. To increase the numerical accuracy near the body, the Cartesian cut cell method is employed. The nonlinear free-surface during green water incident is defined by Marker-density method. The green waters on a box in regular waves are simulated. The simulation results are compared with other experimental and computational results for verification. To check the applicability to moving ship, the green water of the ship which is towed by uniform force in regular wave, is simulated. The ship is set free to heave and to surge.

• Structural Engineering and Mechanics
• /
• 제77권4호
• /
• pp.473-479
• /
• 2021

The propagation of plane waves in a linear, homogeneous and isotropic nonlocal generalized thermoelastic solid medium is considered in the framework of Lord and Shulman generalization. The governing field equations are formulated and specialized in a plane. Plane wave solutions of governing equations show that there exists three plane waves, namely, P, thermal and SV waves which propagate with distinct speeds. Reflection of P and SV waves from thermally insulated or isothermal boundary of a half-space is considered. The relevant boundary conditions are applied at stress free boundary and a non-homogeneous system of three equations in reflection coefficients is obtained. For incidence of both P and SV waves, the expressions for energy ratios of reflected P, thermal and SV waves are also obtained. The speeds and energy ratios of reflected waves are computed for relevant physical constants of a thermoelastic material. The speeds of plane waves are plotted against nonlocal parameter and frequency. The energy ratios of reflected waves are also plotted against the angle of incidence of P wave at a thermally insulated stress-free surface. The effect of nonlocal parameter is shown graphically on the speeds and energy ratios of reflected waves.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2002년도 추계학술발표회
• /
• pp.283-286
• /
• 2002

Solubilization and partitioning of naphthalene was investigated in an aqueous system containing soils and surfactants. The environmental behavior of polycyclic aromatic hydrocarbons(PAHs) was mainly governed by their solubility and partitioning properties on soil media in a subsurface system. In surfactant-enhanced remediation systems, surfactants might be an additional variable. a natural soil ,silica and kaolinite were tested as soil media. two nonionic surfactants, Triton X-100 and Hydropropy1-$\beta$-cyclodextrin (HPCD) were employed for naphthalene solubilization. Naphthalene showed linear on natural soil while non-linear sorption on silica and kaolinite. Soils have higher sorption capacity for Triton X-100 than HPCD indicating Triton X-100 formed ad-micelle on the soil surface. Desorption study showed a hysterysis and reversible desorption. The partitioning coefficient(K$_{D}$) of naphthalene was increased as the concentration of surfactant was increased. (below CMC), however, the coefficient was decreased above CMC. This indicates that naphthalene is partitioned into the micelles and the partition occurs competitively on both ad-micelle and free micelles as surfactant concentration increases. Therefore, the target compounds to be dissolved into aqueous phase in a surfactant enhanced remediation system might be highly partitioned on to the ad-micelle resulting in an adverse effect rather increased solubilization would be achieved.d.

• Fibers and Polymers
• /
• 제6권1호
• /
• pp.1-5
• /
• 2005

In this study, we attempted to evaluate a novel use of sericin-fixed silk fiber (SFx) as an immobilization support of enzyme. Sericin was fixed on the silk fiber using glutaraldehyde as a fixation reagent. After 6 hours of fixation, the degree of fixation increases linearly with linear decrease of the amount of bound $\alpha$-chymotrypsin (CT). This suggests that the increase of the degree of fixation is due to the further crosslinking of free aldehyde groups on the surface of sericin-fixed silk fiber (SFx). Even though perfect fixation was not achieved, sericin did not dissolve seriously and could be removed by further washing. The specific activity did not differ significantly after 6 hours of fixation. The activity of immobilized CT on SFx decreased to its half after 6 hours of incubation at 50$^{\circ}C$. However, it retained $78\%$ of initial activity even after 1 hour of treat­ment with $100\%$ ethanol. As a result, the SFx could be used as an immobilization support of enzyme in non-aqueous media at ambient temperature.