• 한국터널지하공간학회 논문집
• /
• 제25권4호
• /
• pp.305-330
• /
• 2023

쉴드TBM 터널은 NATM 터널과 달리 라이닝이 세그먼트로 분절되어 있다. 따라서 라이닝에 동일 하중이 발생되어도 NATM 터널 라이닝과 쉴드TBM 터널 라이닝의 응력 분포가 다르게 발생된다. 쉴드TBM 터널에서 라이닝에 발생되는 응력을 분석하는 대표적 방법은 연결부를 고려하지 않는 강성일체법과 링간 이음 및 세그먼트 연결을 고려하는 2링 빔스프링 모델이 있다. 본 연구는 라이닝 분절 Segmentaion을 고려한 Break-joint Mode 해석 방법이지만 세그먼트 라이닝 연결부의 구조적 역할을 고려하지 않고 마찰력 성분인 수직강성과 전단강성 만 도입된 쉘 인터페이스 요소를 이용한 모델링을 적용하여 진동하중 발생 시 라이닝의 응력 및 변위에 대한 응답결과를 분석했다. 토압 등 정적 하중에 대해 천 정부에서 가장 큰 응력이 발생되는 강성일체법과 달리 본 연구의 해석방법에 의해 발생된 세그먼트 라이닝 응력 분포는 세그먼트 연결부가 집중된 천정부 Key 세그먼트에서 가장 작은 응력이 발생하였고 연결부를 경계로 응력의 분포가 뚜렷이 구분되었다. 그리고 정적 해석 결과는 강성일체법에 발생된 라이닝 응력이 본 연구 방법에 의해 발생된 세그먼트 라이닝의 응력에 비해 최대 7배의 큰 응력이 발생되었다. 이러한 결과는 세그먼트 연결부를 고려한 기존의 2링 빔-스프링 모델의 응력분포 양상과 일치하는 결과다. 그러나 열차 진동하중에 대한 응력값은 Break-joint Mode로 해석한 본 연구방법의 응력이 강성일체법에 비해 더 큰 응력을 발생되었다. 이는 짧은 부재들의 조합으로 이루어진 세그먼트 Ring이 원주방향으로 일체로 되어 부재의 길이가 상대적으로 더 긴 강성일체법 결과에 비해 더 작은 응력이 발생되는 정역학적 개념과 상이한 결과다. 진동하중에 대해 Break-joint Mode에서 세그먼트 라이닝에 응력이 더 크게 발생된 원인은 부재의 고유주기, 감쇠비 등 동역학적 요인의 차이보다는 열차 진동하중에 대해 라이닝에 발생되는 변위의 차이에 기인하는 것으로 판단되지만 이에 대한 증명은 추후의 과제로 남겨두었다. 본 연구 방법의 Break-joint Mode를 이용하면 정지상태의 열차 하중에 의해 발생되는 라이닝의 응력과 변위값을 비교하여 쉴드TBM 터널의 충격계수(DIF)를 비교적 간단하게 추정할 수 있다. 본 연구는 쉴드TBM 터널의 Segmentaion을 고려한 3차원 모델링으로 추후 지진파 등 다양한 하중조건의 검토를 통해 기존 해석방법 결과와 비교하여 모델링의 추가적 신뢰성을 확보할 필요가 있다.

• Geomechanics and Engineering
• /
• 제28권2호
• /
• pp.117-133
• /
• 2022

Determination of the mechanical behaviour of jointed rock masses has been a challenge for rock engineers for decades. This problem is more pronounced for non-persistent jointed rock masses due to complicated interaction of rock bridges on the overall behaviour. This paper aims to study the effect of a non-persistent joint set configuration on the mechanical behaviour of rock materials under both uniaxial and biaxial compression tests using a discrete element code. The numerical simulation of biaxial compressive strength of rock masses has been challenging in the past due to shortcomings of bonded particle models in reproducing the failure envelope of rock materials. This problem was resolved in this study by employing the flat-joint contact model. The validity of the numerical model was investigated through a comprehensive comparative study against physical uniaxial and biaxial compression experiments. Good agreement was found between numerical and experimental tests in terms of the recorded peak strength and the failure mode in both loading conditions. Studies on the effect of joint orientation on the failure mode showed that four zones of intact, transition to block rotation, block rotation and transition to intact failure occurs when the joint dip angle varies from 0° to 90°. It was found that the applied confining stress can significantly alter the range of these zones. It was observed that the minimum strength occurs at the joint dip angle of around 45 degrees under different confining stresses. It was also found that the joint orientation can alter the post peak behaviour and the lowest brittleness was observed at the block rotation zone.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권3호
• /
• pp.23-27
• /
• 2012

This paper aims to evaluate the feasibility of using no-insulation High Temperature Superconducting (HTS) coil in persistent current mode system. A HTS coil in persistent current mode system usually includes one or more non-superconducting joints in its circuit. And the current decaying rate of the coil is affected by the resistance of joint in persistent current circuit. If the resistance of joint is large, decaying rate of the current drastically increases. Therefore, reducing the joint resistance of the HTS coil is very important in persistent current mode system. In this paper, the no-insulation HTS coil is suggested as a way to reduce the joint resistance with the embedded parallel contact resistance naturally made by no-insulation winding method. Two small coils are fabricated with insulation and no-insulation winding method, and persistent current mode system experiment of each coil is preformed and analyzed.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제10권11호
• /
• pp.5209-5228
• /
• 2016

Device-to-device (D2D) communication underlaying cellular networks can bring significate benefits for improving the performance of mobile services. However, it hinges on elaborate resource sharing scheme to coordinate interference between cellular users and D2D pairs. We formulate a joint mode selection, link allocation and power control optimization problem for D2D communication sharing uplink resources in a multi-user cellular network and consider the efficiency and the fairness simultaneously. Due to the non-convex difficulty, we propose a three-step scheme: firstly, we conduct mode selection for D2D pairs based on a minimum distance metric after an admission control and obtain some cellular candidates for them. And then, a cellular candidate will be paired to each D2D pair based on fairness. Finally, we use Lagrangian Algorithm to formulate a joint power control strategy for D2D pairs and their reused cellular users and a closed-form of solution is derived. Simulation results demonstrate that our proposed algorithms converge in a short time. Moreover, both the sum rate of D2D pairs and the energy efficiency of cellular users are improved.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.481-486
• /
• 1998

In this paper, elastic and inelastic behavior of exterior joint of moment-resisting R.C frame with non-seismic detail subjected to reversed cyclic lateral load such as earthquake excitations was investigated. 1/2-scals subassemblage exterior beam-column joint including slab was manufactured based on similitude law. Then, pseudo static test under the displacement control was performed. The results of 1)crack pattern and failure mode, 2)degradation stiffness and strength, energy dissipation capacity from load-displacement hysteresis curve, 3)strain of steel were analysed.

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.29-42
• /
• 2018

This paper presents the results of an empirical study in which square rock-like blocks containing two parallel pre-existing rough non-persistent joints were subjected to uniaxial compression load. The main purpose of this study was to investigate uniaxial compressive strength and deformation modulus of jointed specimens. Response Surface Method (RSM) was utilized to design experiments and investigate the effect of four joint parameters, namely joint roughness coefficient (JRC), bridge length (L), bridge angle (${\gamma}$), and joint inclination (${\theta}$). The interaction of these parameters on the uniaxial compressive strength (UCS) and deformation modulus of the blocks was investigated as well. The results indicated that an increase in joint roughness coefficient, bridge length and bridge angle increased compressive strength and deformation modulus. Moreover, increasing joint inclination decreased the two mechanical properties. The concept of 'interlocking cracks' which are mixed mode (shear-tensile cracks) was introduced. This type of cracks can happen in higher level of JRC. Initiation and propagation of this type of cracks reduces mechanical properties of sample before reaching its peak strength. The results of the Response Surface Methodology showed that the mutual interaction of the joint parameters had a significant influence on the compressive strength and deformation modulus.

• Geomechanics and Engineering
• /
• 제13권3호
• /
• pp.431-446
• /
• 2017

Rock bridges in rock masses would increase the bearing capacity of Non-persistent discontinuities. In this paper the effect of ratio of rock bridge surface to joint surface, rock bridge shape and normal load on failure behaviour of intermittent rock joint were investigated. A total of 42 various models with dimensions of $15cm{\times}15cm{\times}15cm$ of plaster specimens were fabricated simulating the open joints possessing rock bridge. The introduced rock bridges have various continuities in shear surface. The area of the rock bridge was $45cm^2$ and $90cm^2$ out of the total fixed area of $225cm^2$ respectively. The fabricated specimens were subjected to shear tests under normal loads of 0.5 MPa, 2 MPa and 4 MPa in order to investigate the shear mechanism of rock bridge. The results indicated that the failure pattern and the failure mechanism were affected by two parameters; i.e., the ratio of joint surface to rock bridge surface and normal load. So that increasing in joint area in front of the rock bridge changes the shear failure mode to tensile failure mode. Also the tensile failure change to shear failure by increasing the normal load.

• Earthquakes and Structures
• /
• 제18권1호
• /
• pp.113-127
• /
• 2020

In this study, the behavior of external beam-column joints reinforced by plain and deformed bars with non-seismic reinforcement details is investigated and compared. The beam-column joints represented in this study include a benchmark specimen by seismic details in accordance with ACI 318M-11 requirements and four other deficient specimens. The main defects of the non-seismic beam-column joints included use of plain bar, absence of transverse steel hoops, and the anchorage condition of longitudinal reinforcements. The experimental results indicate that using of plain bars in non-seismic beam-column joints has significantly affected the failure modes. The main failure mode of the non-seismic beam-column joints reinforced by deformed bars was the accumulation of shear cracks in the joint region, while the failure mode of the non-seismic beam-column joints reinforced by plain bars was deep cracks at the joint face and intersection of beam and column and there was only miner diagonal shear cracking at the joint region. In the other way, use of plain bars for reinforcing concrete can cause the behavior of the substructure to be controlled by slip of the beam longitudinal bars. The experimental results show that the ductility of non-seismic beam-column joints reinforced by plain bars has not decreased compared to the beam-column joints reinforced by deformed bars due to lack of mechanical interlock between plain bars and concrete. Also it can be seen a little increase in ductility of substructure due to existence of hooks at the end of the development length of the bars.

• Composites Research
• /
• 제34권5호
• /
• pp.323-329
• /
• 2021

본 논문에서는 불균일한 접착 상태를 가지는 복합재 접착 체결 시편에 대하여 모드 I 하중에서의 파괴 특성을 분석하였다. 이를 위하여 Double Cantilever Beam(DCB) 시험을 수행하였으며 모드 I 파괴 인성을 도출하였다. 불균일한 접착 상태를 갖는 시편의 경우 안정한 균열 성장 구간과 불안정한 균열 성장 구간이 나타남을 확인하였다. DCB 시험에서 구한 하중-변위 선도와 시편의 파손 단면을 통해 각 구간의 파괴 특성을 관찰하였다. 시험에서 측정된 균열 길이를 기준으로 세분화된 구간과 각 구간의 모드 I 파괴 인성을 이용하여 유한요소해석을 수행하였다. DCB 시험 결과와 유한요소해석 결과를 통해 불균일한 접착 상태를 가지는 시편의 파괴 거동을 모사할 수 있음을 확인하였다.

• Computers and Concrete
• /
• 제34권1호
• /
• pp.15-31
• /
• 2024

This study explores the failure mechanisms of 'I' shaped non-persistent cracks under uniaxial loads through a combination of experimental tests and numerical simulations. Concrete specimens measuring 200 mm×200 mm×50 mm were manufactured, featuring 'I' shaped non-persistent joints. The number of these joints varied from one to three, with angles set at 0, 30, 60, and 90 degrees. Twelve configurations, differing in the placement of pre-existing joints, were considered, where larger joints measured 80 mm in length and smaller cracks persisted for 20 mm with a 1 mm crack opening. Numerical models were developed for the 12 specimens, and loading in Y-axis direction was 0.05 mm/min, considering a concrete tensile strength of 5 MPa. Results reveal that crack starting was primarily influenced by the slope of joint that lacks persistence in relation to the loading direction and the number of joints. The compressive strength of the samples exhibited variations based on joint layout and failure mode. The study reveals a correlation between the failure behavior of joints and the number of induced tensile fracture, which increased with higher joint angles. Specimen strength increased with decreasing joint angles and numbers. The strength and failure processes exhibited similarities in both laboratory testing and numerical modeling methods.