• Magazine of the Korea Concrete Institute
• /
• v.7 no.2
• /
• pp.126-135
• /
• 1995

Thermal cracks are occured when thermal stress due to the hydration of cement exceeds the tens~le strength of concrete. Since crackmg causes poor durability of concrete, the effect of ther ma1 cracking should be includod for the design and construction of massive concrete structures. In this study, an experiment is performed for the investigation of time dependent thermal stress history. In order to evaluate thermal stress. two methods are employed. One 1s the evaluation method of thermal stress based on the measurement from embedment stram gauge with non-stress strain gauge and the other 1s based on the measurement from concrete stress gauge. As a result of this study, the value corrected by the former shows good agreement with the latter. The validity of the proposed method for the evaluation of thermal stress 1s explored.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.2
• /
• pp.101-109
• /
• 2016

PURPOSE. To investigate the void parameters within the resin cements used for fiber post cementation by micro-CT (${\mu}CT$) and regional push-out bonding strength. MATERIALS AND METHODS. Twenty-one, single and round shaped roots were enlarged with a low-speed drill following by endodontic treatment. The roots were divided into three groups (n=7) and fiber posts were cemented with Maxcem Elite, Multilink N and Superbond C&B resin cements. Specimens were scanned using ${\mu}CT$ scanner at resolution of $13.7{\mu}m$. The number, area, and volume of voids between dentin and post were evaluated. A method of analysis based on the post segmentation was used, and coronal, middle and apical thirds considered separately. After the ${\mu}CT$ analysis, roots were embedded in epoxy resin and sectioned into 2 mm thick slices (63 sections in total). Push-out testing was performed with universal testing device at 0.5 mm/min cross-head speed. Data were analyzed with Kruskal-Wallis and Mann-Whitney U tests (${\alpha}=.05$). RESULTS. Overall, significant differences between the resin cements and the post level were observed in the void number, area, and volume (P<.05). Super-Bond C&B showed the most void formation ($44.86{\pm}22.71$). Multilink N showed the least void surface ($3.51{\pm}2.24mm^2$) and volume ($0.01{\pm}0.01mm^3$). Regional push-out bond strength of the cements was not different (P>.05). CONCLUSION. ${\mu}CT$ proved to be a powerful non-destructive 3D analysis tool for visualizing the void parameters. Multilink N had the lowest void parameters. When efficiency of all cements was evaluated, direct relationship between the post region and push-out bonding strength was not observed.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.62 no.2
• /
• pp.31-38
• /
• 2020

Controlled Low Strength Material (CLSM) has high fluidity and self-compaction characteristics. CLSM is mainly used for backfilling the excavated road. Early-age properties of CLSM should be characterized for fast restoration of the road. In this study, shear wave monitoring and Vicat needle test are performed to investigate the early-age properties of CLSM depending on the setting time. CLSM consists of CSA cement, fly ash, silt and sand, accelerator, and water. Five fly ashes with different chemical properties are used for CLSM samples. The penetration of CLSM along setting time is obtained through the Vicat needle test. A pair of bender elements are placed in a mold for shear wave measurement, and the change in shear waves with the setting time is monitored. The experimental results show that, regardless of the type of fly ash, the penetration depth decreases and the shear wave velocity increases with the setting time. Depending on the type of fly ash, initial and final times and shear wave velocity change. After testing, the correlation between penetration and shear wave velocity is obtained with high coefficient of determination. The shear wave measurement technique using the bender element can be used to identify early-age properties.

• Korean Journal of Head & Neck Oncology
• /
• v.26 no.2
• /
• pp.243-246
• /
• 2010

Purpose : Eosinophilic granuloma is a rare benign tumor that is characterized histologically by the presence of destructive granulomas containing numerous Langerhans, cells. The most common presentation of eosinophilic granuloma is a painful, immobile scalp mass in the frontal and parietal bones occurring predominantly in children and adolescents or young adults. We report a representative case of eosinophilic granuloma. Methods : A 16-year-old woman complained of an enlarging fixed scalp mass without pain and tenderness which measured $3{\times}4.5cm$ at the frontal area, which had been found incidentally 2 months before. Plain skull x-ray showed a punched-out bone lesion. Computed tomography and magnetic resonance imaging showed a non-enhancing osteolytic lesion. The tumor and surrounding bony edges were completely removed via a bicoronal approach. The bony defect was reconstructed with bone cement. Results : The tumor was involved frontal bone and dura mater. We confirmed the tumor by the documentation of Birbeck's granules by electron microscopy. There is no evidence of local recurrence during postoperative 1.5 years. Conclusion : The present case shows the characteristic feature of frontal bone involvment of the eosinophilic granuloma. The prognosis of eosinophilic granuloma depend on age at diagnosis and number of bones involved. We consider that best choice of treatment for eosinophilic granuloma is surgical excision.

• Asian-Australasian Journal of Animal Sciences
• /
• v.8 no.2
• /
• pp.113-118
• /
• 1995

Eighteen Holstein Friesian ${\times}$ Native heifers with an average live weight of $175.4{\pm}27.8kg$ were allotted to 3 dietary groups. All animals were kept individually in a stanchion barn with free access to water and urea-treated rice straw (UTS). The supplemented feeds were as follows: Group (Gr) 1 - concentrate mixture (15% CP) at 1% body weight (BW), Gr 2 - concentrate mixture at 0.7% BW + free licking of multinutrient block (MNB), Gr 3 - as Gr 2 + 0.3% BW ground com. Multinutrient block composed of 20% mineral mixture, 10% urea, 18% molasses, 20% soybean meal, 22% sesame meal, 10% cement, 0.15 million IU and 50 IU/kg MNB of vitamin A and E. The experimental period lasted 12 weeks. The result revealed that MNB enhanced intake of UTS and total dry matter intake. Animals in Gr 3 consumed a higher amount of feed than the other 2 groups, thus resulting in the highest live weight gain and tended to possess the best feed conversion ratio. Heifers in Gr 2 also performed better than Gr 1 although the difference was not significant. Average MNB intake found to be 0.65 kg/day. Feed cost per kg gain was not significantly different amon groups. However if the cost of MNB could be lower, it would benefit the production cost of animals. The advantage of MNB is the safety of using a high level of urea. Although it was supplemented to UTS which also contained non-protein nitrogen (NPN), no toxic sign was shown. The results indicated that MNB could be partially substituted to concentrate mixture and it was even better when used incombination with soluble carbohydrate feed.

• Resources Recycling
• /
• v.23 no.2
• /
• pp.81-89
• /
• 2014

Approximately 8.5 million tons of fly ash and 740,000 tons of briquette ash were produced in 2010. Inefficient recycling of coal ash has been a heavy economic and environmental burden and economical coal ash utilization technologies are required to turn coal ash into valuable resources. In this study the patents and literature were analyzed to understand the present situation of coal ash recycling technologies and to promote utilization of coal ash for producing a non-sintering green cement, geopolymer. The survey was based on the open patents of USA, European Union, Japan and Korea, and the papers in SCI - indexed journals published between 1979 and 2013. Technical key words were used for data collection and noise filtering. Trends of recycling technologies in utilization of coal ash for producing geopolymers were discussed in terms of time periods, countries, companies and various forms of technologies.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.2
• /
• pp.177-194
• /
• 1991

The purpose of this study was to analyze the magnitude and distribution of stress using a photoelastic model from a distal extension removable partial dentures with three kinds of mandibular major connectors, that is, lingual bar, linguoplate, and swing-lock attachment. A photoelastic model was made of the epoxy resin(PC-1) and hardener(PCH-1) and coated with plastic cement-1 (PC-1) at the lingual surface of the epoxy model and set with three kinds of chrome-cobalt removable partial dentures. A bilateral vertical load of 15kg to the middle portion of the metal bar crossing both the first molars of the right and the left, and a unilateral vertical load of 12.5kg to the right first molar were applied with the use of specially designed loading device and the reflective circular polariscope was used to analyze the photoelastic model under each condition. The following results were obtained : 1. When the bilateral vertical load was applied, the magnitude and distribution of the stress concentration of the edentulous area and the terminal abutment or adjacent teeth was in the order of lingual bar, linguoplate, swing-lock attachment. 2. When the unilateral vertical load was applied, the magnitude and distribution of the stress concentration of the edentulous area and the terminal abutment or adjacent teeth was in the order of lingual bar, linguoplate, swing-lock attachment. 3. When the unilateral vertical load was applied, the magnitude and distribution of the stress concentration of the termial abutment or adjacent teeth on the non-loaded side showed the least stress distribution in case of swing-lock attachment. 4. When the bilateral vertical load and the unilateral vertical load were applied the swing-lock attachment showed the mildest uniform stress distribution on the edentulous area and the alveolar bone around the abutment teeth.

• Asian Journal of Atmospheric Environment
• /
• v.12 no.1
• /
• pp.37-46
• /
• 2018

The Minamata Convention on Mercury entered into force on August 16, 2017. It requires Parties to the Convention to control and, where feasible, reduce mercury emissions from the listed sources. To implement the Convention, Japan amended the Air Pollution Control Law and added clauses that force operators to control their mercury emissions below emission limit values (ELVs). The ELVs have been established separately for new and existing sources, targeting the source categories listed in the Convention: coal-fired boilers, smelting and roasting processes used in the production of non-ferrous metals (lead, zinc, copper and industrial gold), waste incineration facilities and cement clinker production facilities. The factors used to establish the ELVs include the present state of mercury emissions from the targeted categories as well as the mercury content in fuels and materials, best available techniques (BATs) and best environmental practices (BEPs) to control and reduce mercury emissions and ELVs or equivalent standards to control mercury emissions in other countries. In this regard, extensive data on mercury emissions from flue gas and the mercury content of fuels and materials were collected and analyzed. The established ELVs range from $8{\mu}g/Nm^3$ for new coal-fired boilers to $400{\mu}g/Nm^3$ for existing secondary smelting processes used in the production of copper, lead and zinc. This paper illustrates the ELVs for the targeted source categories, explaining the rationales and approaches used to set the values. The amended Law is to be enforced on April 1, 2018. From future perspectives, checks of the material flow of mercury, following up on the state of compliance, review of the ELVs and of the measurement and monitoring methods have been noted as important issues.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.8
• /
• pp.1135-1140
• /
• 2005

Dogs are a very good indicator of the pollution load on the environment. They share people's environment and are exposed to the action of the same pollutants. This study was to estimate the heavy metal contents in dog hairs in domestic districts, and to assess effects of age, sex, feed habits, living area, breeding environment and smoking habit of owner. The mean concentrations of heavy metals in 204 samples were 0.09${\pm}$0.10 ${\mu}g$/g, 0.21${\pm}$0.09 ${\mu}g$/g, 0.82${\pm}$0.09 ${\mu}g$/g and 0.48${\pm}$0.07 ${\mu}g$/g (Cadmium (Cd), Mercury (Hg), Lead (Pb) and Chromium (Cr)) in dog hairs, respectively. Concentrations of Pb, Cd, Hg and Cr in dog hairs in Yeongnam including Ulsan and Seoul, were higher than in Chungchong and Honam, and concentrations of Pb were significantly different (p<0.01). Concentrations of Cd, Hg, Pb and Cr in dog hairs increased with age (p<0.05). Only dogs fed commercial pet foods had significantly higher Cd and Cr concentrations in hairs than dogs fed dog feed and human diet (p<0.01 in Cd and p<0.05 in Cr). Cr concentrations of dog hairsfrom dogs kept on cement floors were the highest of the other environments (p<0.01). Heavy metal concentrations of dogs owned by smokers, were higher than dogs of non-smokers, but there were no significant differences.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.5
• /
• pp.389-395
• /
• 2016

The evolution of electro-mechanical impedance (EMI) of the piezoelectricity (PZT) sensor was investigated to determine the setting times of cementitious materials in this study. The PZT sensor coated with non-conductive acrylic resin was embedded in cement paste before casting and the EMI signatures were continuously measured. Vicat needle test and semi-adiabatic calorimetry test were also conducted to justify the validity of EMI senssing technique in setting monitoring of cementitious materials. The results show that significant changes in EMI resonant peak magnitude and frequency during setting process were observed, and that the setting times determined by EMI sensing technique were relevant to the setting times measured by Vicat needle test and semi-adiabatic calorimetry test.